All products · 6 of 1440
Electronics, sensors, robotics kits, PC components, peripherals — everything Unik Systems carries, in one place.
Arduino Uno R3 CH340G ATMega328P Development Board Compatible with Arduino
[Arduino Boards, Development Board] Product Description The Uno R3 CH340G ATmega328p Development Board is the low-cost version of the popular Uno R3 Arduino. It is assembled with the CH340 USB to Serial converter chip, instead of using an Atmega16U2 chip. We have used plenty of these low-cost Arduino boards with CH340 chips, and have found them to work perfectly. The only time the CH340 chip is used is during programming and when using the serial output of the USB port. During normal operation, this board is identical to the more expensive version without CH340 chip. Features The Arduino Uno R3 is a micro-controller board base on the ATmega328 . It has 14 digital input/output pins (of which 6 can be used as PWM outputs); 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything need to support the micro-controller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get start. The Arduino Uno R3 differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega16U2 (Atmega8U2 up to version R2) program as a USB-to-serial converter. Revision 2 of the Uno board has a resistor pulling the 8U2 HWB line to ground, making it easier to put into DFU mode. Note: The Arduino Uno R3 reference design can use an Atmega8, 168, or 328, Current models use an ATmega328, but an Atmega8 is shown in the schematic for reference. The pin configuration is identical on all three processors. Package Includes 1 x Arduino Uno R3 CH340G ATMega328P Development Board
Unsoldered Nano V3.0 ATmega328P 5V 16MHz CH340 Type-C
[Arduino Boards] This Arduino-compatible Nano V3.0 micro-controller is a small, complete, micro-controller board based on the ATmega328 MCU. It has more or less the same functionality as the Arduino Duemilanove, but in a smaller package. It lacks only a DC power jack, and uses the more compact Mini USB (Mini-B) connector instead of a standard USB connector. It is compatible with Arduino programs and the Arduino IDE. This version of the Nano uses the CH340G USB interface controller. It can be powered via the Mini-B USB connection, a 6-20V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source. Features: CH340G USB bus converter chip replaces FT232RL Operating Voltage（logic level): 5V 8 analog inputs ports: A0 – A7 14 Digital input / output ports: TX, RX, D2 – D13 6 PWM ports: D3, D5, D6, D9, D10, D11 1 pair of TTL level serial transceiver ports: RX / TX Uses Atmel Atmega328P-AU MCU with bootloader installed Support USB download and Power over Mini-B Mini USB connector Recommended input voltage: 7V – 12V DC on pin 30 or 5V on pin 27 Maximum input voltage limits: 6V – 20V Supports ISP download Supplied with connector pins (headers), not soldered to the board for user flexibility Package Includes: 1 X Nano V3.0 16MHz CH340
Nano CH340 Chip Board without USB cable compatible with Arduino (Soldered)
[Arduino Boards] 🔷 Nano V3 CH340 ATmega328P Development Board (Soldered Headers) Compatible with Arduino ATmega328P • CH340 USB Interface • Compact Design • Breadboard Friendly • Ready to Use The Nano V3 CH340 Development Board is a compact and powerful microcontroller board based on the ATmega328P-AU microcontroller. Fully compatible with the Arduino Nano platform, it offers the same functionality as the Arduino Uno in a much smaller, breadboard-friendly form factor, making it ideal for embedded systems, robotics, IoT, automation, and DIY electronics projects. This version features the CH340 USB-to-Serial converter, providing a cost-effective and reliable programming interface. The board comes with pre-soldered headers, allowing it to be plugged directly into a breadboard or PCB without additional soldering. Powered by the ATmega328P running at 16MHz, the Nano provides 14 digital I/O pins, 8 analog input pins, 6 PWM outputs, and supports communication protocols including UART, SPI, and I²C. The onboard bootloader allows programming directly through the Mini USB port using the Arduino IDE. The Nano can be powered through the Mini USB connector, an external 6–20V DC supply, or a regulated 5V input, with automatic power source selection for seamless operation. Note: Some computers may require the CH340 USB driver before the board is recognized. ⭐ Features Based on ATmega328P-AU microcontroller Compatible with Arduino Nano V3 CH340 USB-to-Serial interface Pre-installed Arduino bootloader Pre-soldered header pins Compact breadboard-friendly design 14 Digital I/O pins (6 PWM) 8 Analog input pins 16MHz crystal oscillator Mini USB interface for programming Automatic power source selection Manual reset button ICSP header for direct programming TX, RX, Power and L status LEDs Supports Arduino IDE 📋 Technical Specifications Product Type: Microcontroller Development Board Board Version: Nano V3 Microcontroller: ATmega328P-AU USB Interface: CH340G Operating Voltage: 5V Input Voltage (Recommended): 7V–12V DC Input Voltage Range: 6V–20V DC Digital I/O Pins: 14 PWM Channels: 6 Analog Input Pins: 8 Flash Memory: 32KB SRAM: 2KB EEPROM: 1KB Clock Speed: 16MHz USB Connector: Mini USB Communication Interfaces: UART, SPI, I²C Programming: Arduino IDE Bootloader: Pre-installed Board Dimensions: 43 × 18 mm Mounting: Breadboard Compatible 🔧 Applications Suitable for: Arduino Projects Robotics IoT Devices Home Automation Sensor Interfaces Embedded Systems Educational Projects Industrial Automation Data Logging LED Control Motor Control Smart Home Devices Wearable Electronics DIY Electronics Rapid Prototyping 📦 Package Includes 1 × Nano V3 CH340 ATmega328P Development Board (Soldered Headers) USB Cable Not Included ⚠️ Note Mini USB cable is not included. Some Windows computers may require the CH340 USB driver before programming the board. Compatible with the Arduino IDE after selecting Arduino Nano and the appropriate processor/bootloader settings. Product appearance, PCB color, and component layout may vary slightly depending on the manufacturing batch.
Out of stockATmel MCU ATMEGA16U2 MEGA 2560 R3 Improved Version CH340G Board
[Arduino Boards] The ATmel MCU ATMEGA16U2 MEGA 2560 R3 Improved Version CH340G Board is a micro-controller board base on the ATmega2560. It has a USB host interface to connect with Android based phones, base on the MAX3421e IC. It has 54 digital input/output pins (of which 15 can be used as PWM outputs); 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator; a USB connection, a power jack, an ICSP header, and a reset button. The MEGA ADK is base on the Mega 2560. Similar to the Mega 2560 and Uno, it features an ATmega8U2 program as a USB-to-serial converter. Revision 3 of the Mega ADK board has a resistor pulling the 8U2 HWB line to ground, making it easier to put into DFU(Device Firmware Upgrade) mode. The board has the following new features: 1.0 pin-out: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In the future, shields will be compatible both with the board that uses the AVR, which operate with 5V and with the Arduino Due which operates with 3.3V. The second one is a not connected pin, that is reserved for future purposes. Stronger RESET circuit. The Mega Arduino R3 Android Accessory Development Kit (ADK) can be powered via a USB connection or with an external power supply. The power source is selected automatically. External (non-USB) power can come either from an AC-to-DC adapter (wall-wart) or battery. The adapter can be connected by plugging a 2.1mm centre-positive plug into the board’s power jack. Leads from a battery can be inserted in the GND and Vin pin headers of the POWER connector. Because the Mega R3 Android Accessory Development Kit (ADK) is a USB Host, the phone will attempt to draw power from it when it needs to charge. When the ADK is powered over USB, 500mA total is available for the phone and board. Package Includes : 1 x Mega R3 Android Accessory Development Kit (ADK) board.
Out of stockUno+WiFi R3 AtMega328p+NodeMSU ESP8266 Compatible for Arduino UNO
[Arduino Boards] Arduino UNO WIFI ESP8266 CH340 Development Board Uno+WiFi R3 AtMega328p+NodeMSU ESP8266 8MB Memory USB-TTL CH340G Compatible for Arduino UNO is full integration on one board: Uno R3 ATmega 328 and WiFi ESP8266 with memory 8Mb (MegaByte). All of the modules can work together or separately. And everyone has their own pinout headers. The convenient solution for the development of new projects requiring Uno and WiFi. Via USB you can update sketches and firmware for ATmega328 and for ESP8266. For this onboard have the USB-serial converter CH340G. It is a modernized version of the classic Arduino UNO R3 board. Full integration of a microcontroller ATmega328 and a Wi-Fi chip ESP8266 with 8 MB memory on one board. All modules can work together or individually. Each of the microcontrollers has led to connecting peripheral sensors and modules. A convenient solution for developing new projects that require Wi-Fi. Through USB, you can update sketches and firmware for both ATmega328 and ESP8266. For this on board, there is a UART converter CH340G. The board has a DIP switch, which switches the modes of interaction of microcontrollers ATmegaa328 and esp8266. The operations of this board are very simple. The board has a DIP switch, to connect the modules. For example, USB and ATmega328, USB and ESP8266, ATmega328 and ESP8266. Table DIP- switch: Connection DIP 1 2 3 4 5 6 7 ATmega328<->ESP8266 ON ON OFF OFF OFF OFF OFF USB <->ATmega328 OFF OFF ON ON OFF OFF OFF USB<->ESP8266 (Update firmware or sketch) OFF OFF OFF OFF ON ON ON USB<->ESP8266 (communication) OFF OFF OFF OFF ON ON OFF All independent OFF OFF OFF OFF OFF OFF OFF Features: USB-TTL converter. USB5V (500mA max.)Power IN. Logic Level: 5V. Operating Supply Voltage: 5V. Digital I/O Pins: 14. Analog I/O Pins: 6. Interface Type: serial. Operating temperature: −40С°/+125С°. Specifications: Microcontroller ATmega328IC Wi-Fi Module ESP8266 Input supply voltage (V) 3.3 ~ 5 Current consumption (mA) 800 USB to serial converter CH340G VIN/DC Jack (V) 9 ~ 24 WiFi 802.11 b/g/n 2.4 GHz USB type Micro USB USB Clock Frequency (MHz) 16 Memory Size (MB) 8 Package Includes: 1 x Uno+WiFi R3 AtMega328p+NodeMSU ESP8266 Compatible for Arduino UNO
USB to UART/ESP8266 Adapter Programmer for ESP-01 Wi-Fi Modules with CH340G Chip
[Development Board, ESP Modules] ESP8266 Adapter Programmer / USB TO UART Converter for ESP8266 This USB to UART/ESP8266 Adapter Programmer for ESP-01 WiFi Modules with CH340G Chip converts the signal from a USB interface to a PC / laptop to match a serial module ESP8266. This converter module has a CH340 chip which is reliable and with high performance. It is compatible with most Windows systems. The adapter features integrated capacitors to maintain a current of 1000 μF. USB to ESP-01 adapter module has CH340G USB to TTL driver IC onboard, so you can easily use your computer to do ESP-01 functional debugging. ESP-01 serial wifi module can be directly plugged into the yellow pin header without any connecting wire. USB to UART/ESP8266 Programmer used for an ESP-01 module with the ESP8266 chip. It has CH340G USB to TTL driver IC onboard, so you can easily use your computer to do with ESP-01. Features : Using CH340 turns serial port chip for stable performance and compatibility. Supports all basic windows versions. The adapter plate integrated 1000μF solid capacitors to ensure the current supply The power supply will not be a problem to make the WIFI module crashes unresponsive. Using a 3225 SMD crystal oscillator, improves the stability of serial work, on a beautiful and tall. The interposer board is specifically designed for ESP8266 The USB Turn serial port. Package Includes : 1 x USB to UART/ESP8266 Adapter Programmer for ESP-01 Wi-Fi Modules with CH340G Chip ESP8266 Wifi Modules