All products · 77 of 1440
Electronics, sensors, robotics kits, PC components, peripherals — everything Unik Systems carries, in one place.
Snap Circuit Kit
Circuit modules with snap connectors. Power: 2×AA / 3×AA / 9V (kit dependent). Components: switches, LEDs, buzzer, motor, resistors, capacitors. No soldering. Safe low-voltage learning.
Breadboard Kit
Breadboard: 400/830 tie-points. Jumpers: M-M, M-F. Common parts: resistors (¼W), LEDs, push buttons, potentiometer. Modules: LDR, buzzer, IR, PIR, relay. Power module: 3.3V/5V rails (optional).
Force Pressure Sensor
Force-sensitive resistor, square 1.75×1.5 inch sensing area.
LDR (Light Dependent Resistor)
Resistance varies with light: ~1–10kΩ bright, 100kΩ–1MΩ dark. Use in voltage divider with 10kΩ. Output: analog voltage to ADC.
Out of stock0.96 Inch Blue SPI OLED Display Module 7-Pin 128×64 – SSD1306
[LED/LCD Display] 0.96 Inch Blue SPI OLED Display Module 7-Pin 128×64 – SSD1306 The 0.96-inch Blue OLED Display Module is a compact graphical display based on the SSD1306 driver IC, featuring a 128×64 pixel resolution and blue monochrome display. This version has a 7-pin interface with a dedicated CS (Chip Select) pin, making it suitable for 4-wire SPI communication. The module is factory-configured for SPI and can also be modified for I2C/IIC communication on compatible board versions. With its compact size, wide viewing angle and low-power OLED technology, it is suitable for Arduino, ESP32, ESP8266, STM32, Raspberry Pi and other microcontroller projects. ⭐ Key Features 0.96-inch blue OLED display 128 × 64 pixel resolution SSD1306 driver IC 7-pin interface Dedicated CS (Chip Select) pin Factory configured for 4-wire SPI Supports SPI and I2C/IIC with appropriate configuration 3.3V/5V compatible on supported module versions No backlight required Low power consumption Wide viewing angle of more than 160° Compact PCB design Pre-soldered 7-pin male header Compatible with Arduino, ESP32, ESP8266, STM32 and Raspberry Pi projects 📋 Technical Specifications Display Type: OLED (Organic Light-Emitting Diode) Display Colour: Blue Display Size: 0.96 inch Driver IC: SSD1306 Resolution: 128 × 64 pixels Interface: SPI / I2C Default Interface: 4-wire SPI Input Voltage: 3.3V–5V Viewing Angle: >160° Module Dimensions: Approximately 27 × 27 × 4mm Operating Temperature: Approximately -30°C to +70°C Header: 7-pin male header, pre-soldered Display Type: Monochrome blue OLED 🔌 7-Pin Interface The 7-pin version provides the following connections: GND – Ground VCC – Power supply D0 / SCK / CLK – SPI clock D1 / MOSI / SDA – SPI data RES / RST – Display reset DC / A0 – Data/Command selection CS – Chip Select 🛠️ SPI Connection The module is normally supplied in 4-wire SPI configuration. For an Arduino Uno, a typical connection is: VCC → 5V GND → GND D0 → SCK / D13 D1 → MOSI / D11 RES → Digital I/O DC → Digital I/O CS → Digital I/O The dedicated CS pin allows the OLED to share the SPI bus with other devices such as SD cards or additional SPI peripherals. 🔄 I2C / IIC Configuration On compatible versions, the module can be converted from SPI to I2C by changing the appropriate resistor configuration on the PCB. The supplied board configuration may require: Moving the resistor from R3 to R1 Shorting R8 with solder Using D0 as SCL Using D1 as SDA Configuring DC for the I2C address The exact resistor positions can vary between board revisions, so check the markings on your particular PCB before modification. 🎯 Applications Arduino projects ESP32 projects ESP8266 projects STM32 development Raspberry Pi projects IoT devices Sensor displays Voltage/current meters Battery monitors Temperature displays Digital clocks Data loggers Portable electronic devices Robotics DIY measuring instruments Embedded systems Menu and status displays 💡 Advantages of OLED OLED technology is self-emissive, meaning the pixels produce their own light and do not require a conventional backlight. This provides high contrast, compact construction and a wide viewing angle while keeping power consumption relatively low. ⚠️ Important Notes This is the 7-pin SPI version, not the 6-pin version. The module is normally configured for SPI communication. Check the PCB labels before connecting the module. Do not exceed the specified supply voltage. Although many versions support 5V operation, the exact voltage tolerance can vary between board revisions. I2C operation may require hardware resistor modification. The actual PCB layout and component markings may vary slightly between production batches. Display colour: Blue. Libraries such as Adafruit SSD1306 and U8g2 can be used with compatible microcontrollers. 📦 Package Includes 1 × 0.96 Inch Blue SPI OLED Display Module
1K Ohm Rotary Potentiometer Round Shaft 3 Pin Elcon
[Potentiometer] 1KΩ Rotary Potentiometer Round Shaft Elcon The 1KΩ Rotary Potentiometer Round Shaft Elcon is a reliable 3-pin linear rotary potentiometer designed for adjusting electrical parameters such as voltage, current, brightness, motor speed, and other control functions in electronic circuits. By rotating the shaft, the resistance can be smoothly adjusted across its available range, making it suitable for a wide variety of DIY and electronic applications. With its compact 16mm body, 6mm round shaft, and through-hole mounting design, this potentiometer is easy to install on electronic PCBs and control panels. Its linear resistance characteristics make it suitable for applications such as LED brightness control, fan speed control, motor control, power supply adjustment, and general-purpose voltage control. ⭐ Key Features 1KΩ resistance value 3-pin rotary potentiometer Linear potentiometer Smooth rotary adjustment 6mm round shaft 10mm shaft length Compact 16mm body diameter Through-hole mounting Suitable for PCB and electronic circuits Ideal for voltage and resistance adjustment Suitable for DIY and electronic projects Elcon brand 📋 Technical Specifications Product Type: Rotary Potentiometer Brand: Elcon Resistance Value: 1KΩ Configuration: 3 Pin / Single Gang Tolerance: ±20% Shaft Type: Round Shaft Shaft Diameter: 6mm Shaft Length: 10mm Body Diameter / Width: 16mm Total Height: Approx. 25mm Mounting Type: Through Hole Operating Temperature: -40°C to +80°C Weight: Approx. 8g 🔧 Applications LED Brightness Control Fan Speed Control Motor Speed Control Voltage Adjustment Current Adjustment Power Supply Circuits Audio & Electronic Circuits Arduino Projects DIY Electronics Projects Electronic Prototyping 🛠️ How It Works A potentiometer is a variable resistor with three terminals. The two outer terminals are connected to the resistive track, while the center terminal acts as the wiper. Rotating the shaft changes the wiper position and therefore changes the resistance or output voltage in the circuit. 📦 Package Includes 1 × 1KΩ Rotary Potentiometer Round Shaft Elcon ⚠️ Note Product images are shown for illustrative purposes only and may differ slightly from the actual product. The 1KΩ value, tolerance, dimensions, and shaft length should be verified against the actual product batch before installation.
5K Ohms Rotary Potentiometer Round Shaft 3 Pin Elcon
[Potentiometer] 5KΩ Rotary Potentiometer Round Shaft Elcon The 5KΩ Rotary Potentiometer Round Shaft Elcon is a reliable 3-pin linear rotary potentiometer designed for adjusting electrical parameters such as voltage, current, brightness, motor speed, and other control functions in electronic circuits. By rotating the shaft, the resistance can be smoothly adjusted across its available range, making it suitable for a wide variety of DIY and electronic applications. With its compact 16mm body, 6mm round shaft, and through-hole mounting design, this potentiometer is easy to install on electronic PCBs and control panels. Its linear resistance characteristics make it suitable for applications such as LED brightness control, fan speed control, motor control, power supply adjustment, and general-purpose voltage control. ⭐ Key Features 5KΩ resistance value 3-pin rotary potentiometer Linear potentiometer Smooth rotary adjustment 6mm round shaft 13mm shaft length Compact 16mm body diameter Through-hole mounting Suitable for PCB and electronic circuits Ideal for voltage and resistance adjustment Suitable for DIY and electronic projects Elcon brand 📋 Technical Specifications Product Type: Rotary Potentiometer Brand: Elcon Resistance Value: 5KΩ Configuration: 3 Pin / Single Gang Tolerance: ±20% Shaft Type: Round Shaft Shaft Diameter: 6mm Shaft Length: 13mm Body Diameter / Width: 16mm Total Height: Approx. 28mm Mounting Type: Through Hole Operating Temperature: -40°C to +80°C Weight: Approx. 8g 🔧 Applications LED Brightness Control Fan Speed Control Motor Speed Control Voltage Adjustment Current Adjustment Power Supply Circuits Audio & Electronic Circuits Arduino Projects DIY Electronics Projects Electronic Prototyping 🛠️ How It Works A potentiometer is a variable resistor with three terminals. The two outer terminals are connected to the resistive track, while the center terminal acts as the wiper. Rotating the shaft changes the wiper position and therefore changes the resistance or output voltage in the circuit. 📦 Package Includes 1 × 5KΩ Rotary Potentiometer Round Shaft Elcon ⚠️ Note Product images are shown for illustrative purposes only and may differ slightly from the actual product. The 5KΩ value, tolerance, dimensions, and shaft length should be verified against the actual product batch
DHT11 Digital Temperature and Humidity Sensor Module 3.3V-5V for Arduino & Raspberry Pi
[Temperature Sensor] The DHT11 Digital Temperature and Humidity Sensor Module is a reliable and cost-effective sensor designed to measure ambient temperature and relative humidity. It combines a capacitive humidity sensing element and a thermistor with a built-in digital signal processing unit, providing calibrated digital output directly to microcontrollers. In addition, the DHT11 offers stable performance and excellent long-term reliability, making it suitable for environmental monitoring and automation applications. As a result, it is widely used in weather stations, smart home systems, greenhouse monitoring, HVAC systems, and educational electronics projects. Because the module includes the required pull-up resistor, interfacing with microcontrollers becomes simple and straightforward. Furthermore, only three connections are required: VCC, GND, and Data Output. The sensor operates from a wide voltage range of 3.3V to 5.5V DC, ensuring compatibility with Arduino, Raspberry Pi, ESP32, STM32, NodeMCU, and other development boards. Moreover, readily available libraries and example codes allow quick integration into projects. The DHT11 utilizes advanced digital signal acquisition technology and dedicated temperature-humidity sensing techniques to ensure accurate and dependable measurements. 🔹 Key Features Measures temperature and humidity simultaneously Calibrated digital signal output Low power consumption High reliability and long-term stability Capacitive humidity sensing technology Built-in pull-up resistor on module Compatible with Arduino, ESP32, Raspberry Pi, and STM32 Simple 3-wire interface Easy integration into IoT projects Compact and lightweight design 🔹 Technical Specifications Sensor Model: DHT11 Operating Voltage: 3.3V – 5.5V DC Output Type: Digital Serial Output Humidity Measurement Range: 20%RH – 90%RH Humidity Accuracy: ±5%RH Humidity Resolution: 1%RH Temperature Measurement Range: 0°C – 50°C Temperature Accuracy: ±2°C Temperature Resolution: 1°C Sampling Rate: 1Hz (One Reading Per Second) Long-Term Stability: < ±1%RH/Year Interchangeability: Fully Interchangeable Sensor Technology: Capacitive Humidity Sensor + Thermistor 🔹 Pin Configuration Pin 1 (VCC): 3.3V – 5.5V DC Power Supply Pin 2 (DATA): Digital Serial Data Output Pin 3 (GND): Ground 🔹 Applications This sensor module is suitable for: Arduino projects Raspberry Pi projects ESP32 projects IoT systems Weather monitoring stations Smart home automation Greenhouse monitoring HVAC control systems Environmental monitoring Educational electronics projects 🔹 Package Includes 1 × DHT11 Digital Temperature and Humidity Sensor Module
TP4056 1A Li-Ion Lithium Battery Charging Module with Micro USB 3.7V Charger Board
[Li-ion Rechargeable Battery Charger, Lithium Battery Protection Board] The TP4056 1A Li-Ion Lithium Battery Charging Module – Micro USB is a compact and efficient charging board designed for charging single-cell 3.7V lithium-ion and lithium polymer batteries. It features an onboard Micro USB connector, allowing direct charging from USB power sources such as computers, adapters, and power banks. In addition, the module supports external power input through the IN+ and IN- pads, making it suitable for custom battery charging applications and DIY electronics projects. As a result, users can easily integrate the module into portable devices and battery-powered systems. Because of its compact size and lightweight design, the TP4056 module is ideal for space-limited applications. Furthermore, the onboard charging management IC provides stable charging performance with high accuracy and reliable battery protection. The charging current is set to 1A by default, but it can also be adjusted by changing the onboard programming resistor. Moreover, the module includes dual LED indicators for charging status and full-charge indication. This charging module is widely used in power banks, DIY battery chargers, portable electronics, IoT devices, robotics systems, and rechargeable battery projects. 🔹 Key Features TP4056 lithium battery charging IC Onboard Micro USB input interface Suitable for 3.7V Li-Ion and LiPo batteries Default 1A charging current Adjustable charging current support Dual LED charging status indicators Compact and lightweight design High charging accuracy and stable performance Easy integration into DIY projects 🔹 Technical Specifications Product Type: Lithium Battery Charging Module Charging IC: TP4056 Input Interface: Micro USB Input Voltage: 5V DC Battery Type: 3.7V Li-Ion / LiPo Battery Default Charging Current: 1A Adjustable Current Range: 100mA – 1000mA Charging Method: Constant Current / Constant Voltage Charging Indicators: Charging LED & Full Charge LED Mounting Type: PCB Module Body Material: FR4 PCB 🔹 Applications This TP4056 charging module is suitable for many electronic applications, including: DIY power banks Rechargeable battery projects Portable electronics Robotics systems IoT devices Battery charging circuits Arduino projects DIY electronics projects 🔹 Package Includes 1 × TP4056 1A Li-Ion Lithium Battery Charging Module – Micro USB
GL-12 840 Points Solderless Breadboard
[Breadboard and Zero PCBs] A GL-12 840 Points Solderless Breadboard is an invaluable tool for experimenting with circuit designs whether in the R&D or university lab. A breadboard is used to make up temporary circuits for testing or to try out an idea. No soldering is required so it is easy to change connections and replace components. Parts will not be damaged so they will be available for re-use afterward. 840 Tie points – 128 Groups of 5 connected terminals, 8 Bus of 25 connected terminals Reusable for fast build a prototype of an electronic circuit – will accept transistors, diodes, LEDs, resistors, capacitors and virtually all types of components – No soldering required – Can modify or revise the circuits easily Fit for jumper wire of 0.8mm diameter – Standard 2.54mm hole spacing Adhesive sheet on the back side of the board – Multiple breadboards can be spliced together too. Features: 100% brand new and high quality Practical and useful Solderless breadboard with 840 points Completely reusable and have a self-adhesive back Easy component placement Package Includes: 1 x GL-12 840 Points Solderless Breadboard
Out of stockZB2L3 18650 Li-ion Lithium Lead-acid Battery Capacity Meter Discharge Tester Analyzer
[Battery Capacity Tester] Description: Material: Electrical components Color: See pictures ZB2L3 battery capacity tester discharge type 1.2-12V external load capacity of the battery and other tests 18650 Tools, single-function, by controlling the load off and get real-time integrated discharge current capacity results Maximum support 15V 3A discharged through the discharge voltage and current, itself does not discharge Maximum capacity statistics support 9999Ah (9999000mAh) Automatically identifying and developing appropriate battery termination voltage can also be manually adjusted Specifications: Power supply voltage: DC4.5-6V (micro USB connector) Operating Current: less than 70mA Discharge voltage: 1.00V-15.00V 0.01V resolution Termination voltage range: 0.5-11.0V Supported by current: 3.000A 0.001A resolution Maximum voltage measurement error: 1% + 0.02V Maximum current measurement error: 1.5% + – 0.008A Maximum battery capacity range: 9999Ah (1Ah = 1000mAh) greater value by shifting the decimal point to switch, when the display is less than 10Ah X.XXX, as shown above to achieve 10Ah XX.XX, and so on. Board size: 50mmX37mm Finished Size: 50mmX37mmX17mm (length X width X height maximum position size, contains copper foot height) Instructions: 1. The first test should be a fully charged battery. 2. Connect the battery to be tested positive to positive input, a negative input to the negative, can not be reversed (with load reversal may damage the circuit)! Load connected to the output of the positive and negative output, to work through the tester micro USB power supply (not available desktop or laptop USB powered), then the battery voltage. 3. Direct start test need only one press of the “OK” button, the tester can automatically develop an appropriate termination voltage of the battery full charge voltage, and will start flashing after the test three times. Need to develop artificial termination voltage only when the battery voltage display state by pressing “+” or “-” buttons to modify the termination voltage display beginning with P, behind the representative voltage resolution 0.1V, set up after pressing the “OK “start testing. 4. After the start of the test the tester will control the load of the electronic switch is turned on, the test data shows that the process will release capacity (Ah), current discharge current (A) and battery voltage (V) between the wheel was. When the battery voltage reaches the set cut-off voltage, load control switches off the tester display data stays in capacity (Ah) and above and the corresponding indicator flashes quickly together, now displays the actual capacity of the battery is discharging capacity, about the press “OK” to terminate flashing allows stable data display, press again “OK” button to return to the power-on state can just replace the battery test the next section …… Error codes and their meanings: Err1: battery voltage is above 15V Err2: battery voltage is lower than the termination voltage Err3: Battery can not afford to load or discharge current line too much resistance Err4: overcurrent (current exceeds 3.1A) Err5:Improper use or incorrect wiring has caused the device to be burned out and cannot be used (current sampling or control switch MOS burned out). Note: Use the resistance of the discharge process, resistive load will seriously heat, please pay attention to safety! This circuit voltage in order to improve the measurement accuracy, specially designed DC bias, when the terminal displays nothing then a small voltage does not affect the actual measurement, if you are shorting the input terminals (absolute 0V) will show 0 No retail package Quantity:1Pc Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!! Package Content: 1Pc x battery capacity tester 2Pc x Load resistor Power Battery Capacity Tester LED Display Micro USB Li-ion Lithium 18650 External Load Battery Discharge Testing Analyzer
100K Rotary Potentiometer Round Shaft Elcon
[Potentiometer] 100KΩ Rotary Potentiometer Round Shaft Elcon The 100KΩ Rotary Potentiometer Round Shaft Elcon is a reliable 3-pin linear rotary potentiometer designed for adjusting electrical parameters such as voltage, current, brightness, motor speed, and other control functions in electronic circuits. By rotating the shaft, the resistance can be smoothly adjusted across its available range, making it suitable for a wide variety of DIY and electronic applications. With its compact 16mm body, 6mm round shaft, and through-hole mounting design, this potentiometer is easy to install on electronic PCBs and control panels. Its linear resistance characteristics make it suitable for applications such as LED brightness control, fan speed control, motor control, power supply adjustment, and general-purpose voltage control. ⭐ Key Features 100KΩ resistance value 3-pin rotary potentiometer Linear potentiometer Smooth rotary adjustment 6mm round shaft 13mm shaft length Compact 16mm body diameter Through-hole mounting Suitable for PCB and electronic circuits Ideal for voltage and resistance adjustment Suitable for DIY and electronic projects Elcon brand 📋 Technical Specifications Product Type: Rotary Potentiometer Brand: Elcon Resistance Value: 100KΩ Configuration: 3 Pin / Single Gang Tolerance: ±20% Shaft Type: Round Shaft Shaft Diameter: 6mm Shaft Length: 13mm Body Diameter / Width: 16mm Total Height: Approx. 28mm Mounting Type: Through Hole Operating Temperature: -40°C to +80°C Weight: Approx. 8g 🔧 Applications LED Brightness Control Fan Speed Control Motor Speed Control Voltage Adjustment Current Adjustment Power Supply Circuits Audio & Electronic Circuits Arduino Projects DIY Electronics Projects Electronic Prototyping 🛠️ How It Works A potentiometer is a variable resistor with three terminals. The two outer terminals are connected to the resistive track, while the center terminal acts as the wiper. Rotating the shaft changes the wiper position and therefore changes the resistance or output voltage in the circuit. 📦 Package Includes 1 × 100KΩ Rotary Potentiometer Round Shaft Elcon ⚠️ Note Product images are shown for illustrative purposes only and may differ slightly from the actual product. The 100KΩ value, tolerance, dimensions, and shaft length should be verified against the actual product batch before installation.
10K Rotary Potentiometer Round Shaft 3Pin Elcon
[Potentiometer] 10KΩ Rotary Potentiometer Round Shaft Elcon The 10KΩ Rotary Potentiometer Round Shaft Elcon is a reliable 3-pin variable resistor designed for adjusting electrical parameters such as voltage, current, brightness, motor speed, and other control functions in electronic circuits. By rotating the shaft, the resistance can be smoothly adjusted across its available range, making it suitable for a wide variety of DIY and electronic applications. With its compact 16mm body, 6mm round shaft, and through-hole mounting design, this potentiometer is easy to install on electronic PCBs and control panels. The linear resistance characteristics make it particularly suitable for applications such as LED brightness control, fan speed control, motor control, and general-purpose voltage adjustment. ⭐ Key Features 10KΩ resistance value 3-pin rotary potentiometer Linear potentiometer Smooth rotary adjustment 6mm round shaft Compact 16mm body diameter Through-hole mounting Suitable for PCB and electronic circuits Useful for voltage and current adjustment Suitable for LED, fan and motor control applications Elcon brand 📋 Technical Specifications Product Type: Rotary Potentiometer Brand: Elcon Resistance Value: 10KΩ Configuration: 3 Pin / Single Gang Tolerance: ±20% Shaft Type: Round Shaft Shaft Diameter: 6mm Shaft Length: 13mm Body Diameter / Width: 16mm Total Height: 30mm Mounting Type: Through Hole Operating Temperature: -40°C to +80°C Weight: Approx. 8g 🔧 Applications LED Brightness Control Fan Speed Control Motor Speed Control Voltage Adjustment Current Adjustment Power Supply Circuits Arduino Projects DIY Electronics Projects Audio & Electronic Circuits Electronic Prototyping 🛠️ How It Works A potentiometer is a variable resistor with three terminals. The two outer terminals are connected to the resistive track, while the center terminal acts as the wiper. Rotating the shaft changes the wiper position and therefore changes the resistance or output voltage in the circuit. 📦 Package Includes 1 × 10KΩ Rotary Potentiometer Round Shaft Elcon ⚠️ Note Product images are shown for illustrative purposes only and may differ slightly from the actual product. The 10KΩ value and ±20% tolerance are based on the supplied product specifications.
RC3563 Battery Internal Resistance Tester – Handheld Battery Analyzer
[Battery Capacity Tester] RC3563 Battery Internal Resistance Tester – High Precision Battery Resistance & Voltage Meter The RC3563 Battery Internal Resistance Tester is a professional handheld measuring instrument designed for accurate testing of battery internal resistance, battery voltage, and low-value resistance. Using the Kelvin 4-wire measurement method, it minimizes errors caused by lead and contact resistance, providing stable and precise readings. Featuring an LCD display, USB rechargeable operation, and a compact portable design, the RC3563 is suitable for testing Li-ion, LiFePO₄, NiMH, NiCd, Lead-Acid batteries, capacitors, resistors, and other low-resistance components. It is ideal for battery maintenance, EV battery inspection, manufacturing, laboratories, electronics repair, and DIY applications. ⭐ Key Features Simultaneous measurement of internal resistance and voltage High-precision Kelvin 4-wire testing technology Low-resistance measurement capability Clear LCD digital display Portable handheld design 5V USB rechargeable operation Stable and accurate measurement algorithm Suitable for lithium, nickel, and lead-acid batteries Suitable for capacitor and resistor low-resistance testing Ideal for laboratory, industrial, repair, and DIY applications 📋 Technical Specifications Product Type: Battery Internal Resistance Tester Model: RC3563 Measurement Type: Internal Resistance & Voltage Test Method: Kelvin 4-Wire Display: LCD Screen Charging Input: 5V DC Power Supply: Built-in Rechargeable Battery Supported Batteries: Lithium, LiFePO₄, Nickel, Lead-Acid Additional Function: Low Resistance Measurement Design: Handheld Portable Device 🔧 Applications 18650 Battery Testing 21700 Battery Testing Lithium Battery Testing LiFePO₄ Battery Testing Battery Pack Testing EV Battery Inspection UPS & Inverter Battery Testing Lead-Acid Battery Diagnostics Battery Manufacturing & Quality Control Electronics Repair & Servicing Laboratory Testing Capacitor Testing Low Resistance Measurement ⚠️ Precautions Ensure correct polarity when connecting the test probes. Do not short-circuit the test leads. Use only a 5V charging input. Handle the test clips carefully for accurate measurements. Keep the tester away from water and excessive humidity. Avoid extreme temperatures. 📦 Package Includes 1 × RC3563 Battery Internal Resistance Tester 1 × Kelvin 4-Wire Test Lead Set 1 × USB Charging Cable 1 × User Manual
6S 12A Lithium Battery 18650 Charger PCB BMS Protection Board
[Lithium Battery Protection Board] Description PCB BMS 6 Series 22V 18650 Lithium Battery Protection Board is a 6 string 22V circuit power tool mostly used for solar lighting, for dedicated 18650 battery packs. It is designed for 3.7V 18650 models lithium batteries for charging, Protection from overcharge and over-discharge. Battery protection board, as the name suggests battery protection board is mainly rechargeable (Refers to the lithium battery) and protects the integrated circuit board. Lithium battery (rechargeable type) so need protection, is determined by its own characteristics. As the lithium battery, its material determines itself can not be overcharge, over-discharge, overcurrent, short circuit, and ultra-high temperature charge and discharge, so lithium battery lithium components will always follow A protective plate with a sampling resistor, and a current fuse. Application: Battery pack Consumer electronics product 12V voltage rating Power supply Power bank and charger Features/Specs: Battery: 6 Cell Overcharge detection voltage: 4.25 ± 0.025V Over-discharge detection voltage: 2.50 ± 0.08V Overcurrent Protection: 50A Working current: 12A Operating Temperature: -40~+85°C Balanced charge: None. Short circuit protection: Yes. Applicable assembly: Nominal 3.7V Batteries / 6 strings Length: 50mm Width: 32mm Height: 4mm Weight: 6gm Package Includes: 1 x 6S 12A Lithium Battery 18650 Charger PCB BMS Protection Board Note: Product Images are shown for illustrative purposes only and may differ from the actual product
JHD 16×2 Character LCD Display With Blue Backlight
[LED/LCD Display Module] If you want to add some visual output to your Arduino projects, you’ll need a display. If you need only a little to display, the LCD 16×2 Parallel LCD Display is a quite good solution. This is a Original JHD 16×2 Character LCD Display With Blue Backlight as there are many fake JHD Displays in the Market. This is a great blue backlight LCD display. It is fantastic for Arduino based project. This LCD 16×2 Parallel LCD Display with Blue Backlight is very easy to interface with Arduino or Other Microcontrollers. This is LCD 16×2 Parallel LCD Display that provides a simple and cost-effective solution for adding a 16×2 White on RGB Liquid Crystal Display into your project. The display is 16 character by 2 line display that has a very clear and high contrast white text upon a blue background/backlight. The values shown on the display can be either simple text or numerical values read by the sensors, such as temperature or pressure, or even the number of cycles that the Arduino is performing. For more displays click below, LED/LCD Display Features : 16 characters wide, 2 rows White text on the yellow background Single LED backlight included can be dimmed easily with a resistor or PWM. Can be fully controlled with only 6 digital lines! (Any analog/digital pins can be used) Specifications: Model： JHD659 B/W Display： 16×2 character Outline： 80.0×36.0×14.5 VA： 64.5×14.5 Controller： SPLC780D Character： 2.95×4.35 Driver： 1/16 LCD： STN Blue Negative Backlight： White LED Package Includes : 1 x JHD 16×2 Character LCD Display With Blue Backlight
Daly Lifepo4 8S 24V 30A Battery Management System
[Lithium Battery Protection Board] Daly Lifepo4 8S 24V 30A Battery Management System Circuit is an 8Cell in Series 24V circuit power tool mostly used for solar lighting. It is designed for lithium Batteries for charging and protection from overcharge, and Over-discharge. The battery protection board, as the name suggests battery protection board is mainly rechargeable and protects the integrated circuit board. Lithium batteries (rechargeable type) need protection, which is determined by their own characteristics. As the Orange lithium battery, its material determines itself can not be overcharged, overcharged, overcurrent, short circuit, or ultra-high temperature charge and discharge, so lithium battery lithium components will always follow A protective plate with a sampling resistor, and a current fuse. Features: State of charge calculations. Cell over-voltage and under-voltage protection. Intelligent battery balancing (passive). Fully sealed waterproof technology, with waterproof, dustproof, shockproof, anti-squeezing, and other protective functions Cable Size (AWG): 12 Charge Current(A) :30A Length (mm): 80 Width (mm): 60 Height (mm): 10 Model: 8S 24V 30A Over Discharge Detect(V) : 2.2±0.1 Over Discharge Release(V): 2.7±0.1 Overcharge Detect Voltage(V): 3.75±0.05 overcharge Release Voltage(V): 3.55±0.05 Weight (g):: 86 Operating Temperature (°C) :-20 to 70 Shipping Weight0.165 kgShipping Dimensions16 × 11 × 6 cm Package Includes: 1 x Daly Lifepo4 8S 24V 30A Battery Management System
Out of stockLCD2004 Parallel LCD Display Yellow Backlight with IIC/I2C Interface
[LED/LCD Display Module] If you want to add some visual output to your Arduino projects, you’ll need a display. If you need moderate data on display, the LCD2004 Parallel LCD Display is a quite good solution. This is LCD2004 Parallel LCD Display that provides a simple and cost-effective solution for adding a 20×4 Black on RGB Liquid Crystal Display into your project. The display is 20 character by 4 line display has a very clear and high contrast black text upon a yellow background/backlight. This is great yellow backlight LCD display. It is fantastic for Arduino based project. This LCD2004 Parallel LCD Display with Yellow Backlight is very easy to interface with Arduino or Other Microcontrollers. The values shown on the display can be either a simple text or numerical values read by the sensors, such as temperature or pressure, or even the number of cycles that the Arduino is performing. One thing to consider is you’ll waste about 8 Pins on your Arduino for the display to get working. Luckily there exists an I2C adapter that you can solder right onto the pins of the display. So all you need to connect are the I2C pins, which shows a good library and little of coding. For more displays click below, LED/LCD Display Features : 20 characters wide, 4 rows Black text on the yellow background The module can easily interface with an MCU The module is a low-power consumption character LCD Module with a built-in controller Single LED backlight included can be dimmed easily with a resistor or PWM. Can be fully controlled with only 6 digital lines! (Any analog/digital pins can be used) Package Includes : 1 x LCD2004 Parallel LCD Display Yellow Backlight with IIC/I2C Interface
Arduino Uno R3 CH340G ATMega328P Development Board Compatible with Arduino
[Arduino Boards, Development Board] Product Description The Uno R3 CH340G ATmega328p Development Board is the low-cost version of the popular Uno R3 Arduino. It is assembled with the CH340 USB to Serial converter chip, instead of using an Atmega16U2 chip. We have used plenty of these low-cost Arduino boards with CH340 chips, and have found them to work perfectly. The only time the CH340 chip is used is during programming and when using the serial output of the USB port. During normal operation, this board is identical to the more expensive version without CH340 chip. Features The Arduino Uno R3 is a micro-controller board base on the ATmega328 . It has 14 digital input/output pins (of which 6 can be used as PWM outputs); 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything need to support the micro-controller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get start. The Arduino Uno R3 differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega16U2 (Atmega8U2 up to version R2) program as a USB-to-serial converter. Revision 2 of the Uno board has a resistor pulling the 8U2 HWB line to ground, making it easier to put into DFU mode. Note: The Arduino Uno R3 reference design can use an Atmega8, 168, or 328, Current models use an ATmega328, but an Atmega8 is shown in the schematic for reference. The pin configuration is identical on all three processors. Package Includes 1 x Arduino Uno R3 CH340G ATMega328P Development Board
1K Ohm Linear Taper 16mm Rotary Potentiometer Elcon
[Potentiometer] Elcon B1K 1KΩ 16mm Rotary Potentiometer – 3 Pin D-Type Shaft The Elcon B1K 1KΩ Rotary Potentiometer is a compact 3-pin linear taper potentiometer designed for adjusting voltage, resistance, tone, brightness, speed, and other electrical parameters in electronic circuits. It has a total resistance of 1KΩ, with the resistance distributed linearly across the rotation of the shaft. The potentiometer can be used as a variable resistor or as a variable voltage divider. The two outer pins provide the full resistance value, while the center pin acts as the wiper and provides an adjustable resistance or voltage depending on the circuit connection. Its D-type shaft provides a secure grip for a compatible knob, while the included nut allows the potentiometer to be securely fixed to a panel or enclosure. The compact 16mm body makes it suitable for PCB and general-purpose electronic applications. ⭐ Key Features 1KΩ total resistance B1K linear taper 3-pin configuration D-type shaft Compact 16mm potentiometer Includes fixing nut Suitable for PCB mounting Can be used as a variable resistor Can be used as a variable voltage divider Suitable for tone and electronic control applications Breadboard compatible according to the supplied specifications 📋 Technical Specifications Product Type: Rotary Potentiometer Brand: Elcon Potentiometer Value: B1K / 1KΩ Taper: Linear Number of Pins: 3 Shaft Type: D-Type Shaft Diameter: 4mm Shaft Length: 8–10mm Pins Pitch: 4.4mm Dimensions: 25mm × 16mm × 16mm Nut Inner Diameter: 6mm Nut Outer Diameter: 10mm Mounting: PCB / Panel Mount Breadboard Compatible: Yes 🔌 Pin Function Outer Pin 1: Resistive track terminal Center Pin: Wiper / Variable output Outer Pin 3: Resistive track terminal The resistance between the two outer pins remains approximately 1KΩ, while the resistance between the center pin and either outer pin changes as the shaft is rotated. 🔧 Applications Tone Control Audio Circuits Volume & Signal Adjustment LED Brightness Control Motor Speed Control Voltage Adjustment Variable Resistor Applications Arduino Projects DIY Electronics Projects PCB Prototyping General Electronic Control Circuits 🛠️ How It Works When used as a potentiometer, the center pin acts as the adjustable wiper and can provide a variable output across the rotation range. When used as a variable resistor, the wiper can be connected with one of the outer terminals to obtain an adjustable resistance. 📦 Package Includes 1 × Elcon B1K 1KΩ 3-Pin Rotary Potentiometer 1 × Fixing Nut ⚠️ Note Product images are for illustrative purposes only and may differ slightly from the actual product. The supplied specifications state a shaft length of 8–10mm; please verify the exact dimensions against the available product batch before installation.
100K Ohm Linear Taper 16mm Rotary Potentiometer Elcon
[Potentiometer] Elcon B100K 100KΩ 16mm Rotary Potentiometer – 3 Pin D-Type Shaft The Elcon B100K 100KΩ Rotary Potentiometer is a compact 3-pin linear taper potentiometer designed for adjusting voltage, resistance, signal levels, brightness, motor speed, and other electrical parameters in electronic circuits. It has a total resistance of 100KΩ, with the resistance distributed linearly across the rotation of the shaft. The potentiometer can be used as a variable resistor or as a variable voltage divider. The two outer pins provide the full resistance value, while the center pin acts as the wiper and provides an adjustable resistance or voltage depending on the circuit connection. Its D-type shaft provides a secure grip for a compatible knob, while the included nut allows the potentiometer to be securely fixed to a panel or enclosure. The compact 16mm body makes it suitable for PCB and general-purpose electronic applications. ⭐ Key Features 100KΩ total resistance B100K linear taper 3-pin configuration D-type shaft Compact 16mm potentiometer Includes fixing nut Suitable for PCB mounting Can be used as a variable resistor Can be used as a variable voltage divider Suitable for tone and electronic control applications Breadboard compatible according to the supplied specifications 📋 Technical Specifications Product Type: Rotary Potentiometer Brand: Elcon Potentiometer Value: B100K / 100KΩ Taper: Linear Number of Pins: 3 Shaft Type: D-Type Shaft Diameter: 4mm Shaft Length: 8–10mm Pins Pitch: 4.4mm Dimensions: 25mm × 16mm × 16mm Nut Inner Diameter: 6mm Nut Outer Diameter: 10mm Mounting: PCB / Panel Mount Breadboard Compatible: Yes 🔌 Pin Function Outer Pin 1: Resistive track terminal Center Pin: Wiper / Variable output Outer Pin 3: Resistive track terminal The resistance between the two outer pins remains approximately 100KΩ, while the resistance between the center pin and either outer pin changes as the shaft is rotated. 🔧 Applications Tone Control Audio Circuits Signal Level Adjustment LED Brightness Control Motor Speed Control Voltage Adjustment Variable Resistor Applications Arduino Projects DIY Electronics Projects PCB Prototyping General Electronic Control Circuits 🛠️ How It Works When used as a potentiometer, the center pin acts as the adjustable wiper and provides a variable output across the rotation range. When used as a variable resistor, the wiper can be connected with one of the outer terminals to obtain an adjustable resistance. 📦 Package Includes 1 × Elcon B100K 100KΩ 3-Pin Rotary Potentiometer 1 × Fixing Nut ⚠️ Note Product images are for illustrative purposes only and may differ slightly from the actual product. The supplied specifications state a shaft length of 8–10mm; please verify the exact dimensions against the actual product batch before installation.
5K Ohm Linear Taper 16mm Rotary Potentiometer-Elcon
[Potentiometer] Elcon B5K 5KΩ 16mm Rotary Potentiometer – 3 Pin D-Type Shaft The Elcon B5K 5KΩ Rotary Potentiometer is a compact 3-pin linear taper potentiometer designed for adjusting voltage, resistance, tone, brightness, motor speed, and other electrical parameters in electronic circuits. It has a total resistance of 5KΩ, with the resistance distributed linearly across the rotation of the shaft. The potentiometer can be used as a variable resistor or as a variable voltage divider. The two outer pins provide the full resistance value, while the center pin acts as the wiper and provides an adjustable resistance or voltage depending on the circuit connection. Its D-type shaft provides a secure grip for a compatible knob, while the included nut allows the potentiometer to be securely fixed to a panel or enclosure. The compact 16mm body makes it suitable for PCB and general-purpose electronic applications. ⭐ Key Features 5KΩ total resistance B5K linear taper 3-pin configuration D-type shaft Compact 16mm potentiometer Includes fixing nut Suitable for PCB mounting Can be used as a variable resistor Can be used as a variable voltage divider Suitable for tone and electronic control applications Breadboard compatible according to the supplied specifications 📋 Technical Specifications Product Type: Rotary Potentiometer Brand: Elcon Potentiometer Value: B5K / 5KΩ Taper: Linear Number of Pins: 3 Shaft Type: D-Type Shaft Diameter: 4mm Shaft Length: 8–10mm Pins Pitch: 4.4mm Dimensions: 25mm × 16mm × 16mm Nut Inner Diameter: 6mm Nut Outer Diameter: 10mm Mounting: PCB / Panel Mount Breadboard Compatible: Yes 🔌 Pin Function Outer Pin 1: Resistive track terminal Center Pin: Wiper / Variable output Outer Pin 3: Resistive track terminal The resistance between the two outer pins remains approximately 5KΩ, while the resistance between the center pin and either outer pin changes as the shaft is rotated. 🔧 Applications Tone Control Audio Circuits Volume & Signal Adjustment LED Brightness Control Motor Speed Control Voltage Adjustment Variable Resistor Applications Arduino Projects DIY Electronics Projects PCB Prototyping General Electronic Control Circuits 🛠️ How It Works When used as a potentiometer, the center pin acts as the adjustable wiper and provides a variable output across the rotation range. When used as a variable resistor, the wiper can be connected with one of the outer terminals to obtain an adjustable resistance. 📦 Package Includes 1 × Elcon B5K 5KΩ 3-Pin Rotary Potentiometer 1 × Fixing Nut ⚠️ Note Product images are for illustrative purposes only and may differ slightly from the actual product. The supplied specifications state a shaft length of 8–10mm; please verify the exact dimensions against the actual product batch before installation.
10K Ohm Linear Taper 16mm Rotary Potentiometer Elcon
[Potentiometer] Elcon B10K 10KΩ 16mm Rotary Potentiometer – 3 Pin D-Type Shaft The Elcon B10K 10KΩ Rotary Potentiometer is a compact 3-pin linear taper potentiometer designed for adjusting voltage, resistance, tone, brightness, motor speed, and other electrical parameters in electronic circuits. It has a total resistance of 10KΩ, with the resistance distributed linearly across the rotation of the shaft. The potentiometer can be used as a variable resistor or as a variable voltage divider. The two outer pins provide the full resistance value, while the center pin acts as the wiper and provides an adjustable resistance or voltage depending on the circuit connection. Its D-type shaft provides a secure grip for a compatible knob, while the included nut allows the potentiometer to be securely fixed to a panel or enclosure. The compact 16mm body makes it suitable for PCB and general-purpose electronic applications. ⭐ Key Features 10KΩ total resistance B10K linear taper 3-pin configuration D-type shaft Compact 16mm potentiometer Includes fixing nut Suitable for PCB mounting Can be used as a variable resistor Can be used as a variable voltage divider Suitable for tone and electronic control applications Breadboard compatible according to the supplied specifications 📋 Technical Specifications Product Type: Rotary Potentiometer Brand: Elcon Potentiometer Value: B10K / 10KΩ Taper: Linear Number of Pins: 3 Shaft Type: D-Type Shaft Diameter: 4mm Shaft Length: 8–10mm Pins Pitch: 4.4mm Dimensions: 25mm × 16mm × 16mm Nut Inner Diameter: 6mm Nut Outer Diameter: 10mm Mounting: PCB / Panel Mount Breadboard Compatible: Yes 🔌 Pin Function Outer Pin 1: Resistive track terminal Center Pin: Wiper / Variable output Outer Pin 3: Resistive track terminal The resistance between the two outer pins remains approximately 10KΩ, while the resistance between the center pin and either outer pin changes as the shaft is rotated. 🔧 Applications Tone Control Audio Circuits Volume & Signal Adjustment LED Brightness Control Motor Speed Control Voltage Adjustment Variable Resistor Applications Arduino Projects DIY Electronics Projects PCB Prototyping General Electronic Control Circuits 🛠️ How It Works When used as a potentiometer, the center pin acts as the adjustable wiper and provides a variable output across the rotation range. When used as a variable resistor, the wiper can be connected with one of the outer terminals to obtain an adjustable resistance. 📦 Package Includes 1 × Elcon B10K 10KΩ 3-Pin Rotary Potentiometer 1 × Fixing Nut ⚠️ Note Product images are for illustrative purposes only and may differ slightly from the actual product. The supplied specifications state a shaft length of 8–10mm; please verify the exact dimensions against the actual product batch before installation.