All products · 11 of 1440
Electronics, sensors, robotics kits, PC components, peripherals — everything Unik Systems carries, in one place.
Only 2 leftIR Sensor Array (Line Following)
IR sensor array for line-following robots.
Out of stock0.96 Inch Blue SPI OLED Display Module 7-Pin 128×64 – SSD1306
[LED/LCD Display] 0.96 Inch Blue SPI OLED Display Module 7-Pin 128×64 – SSD1306 The 0.96-inch Blue OLED Display Module is a compact graphical display based on the SSD1306 driver IC, featuring a 128×64 pixel resolution and blue monochrome display. This version has a 7-pin interface with a dedicated CS (Chip Select) pin, making it suitable for 4-wire SPI communication. The module is factory-configured for SPI and can also be modified for I2C/IIC communication on compatible board versions. With its compact size, wide viewing angle and low-power OLED technology, it is suitable for Arduino, ESP32, ESP8266, STM32, Raspberry Pi and other microcontroller projects. ⭐ Key Features 0.96-inch blue OLED display 128 × 64 pixel resolution SSD1306 driver IC 7-pin interface Dedicated CS (Chip Select) pin Factory configured for 4-wire SPI Supports SPI and I2C/IIC with appropriate configuration 3.3V/5V compatible on supported module versions No backlight required Low power consumption Wide viewing angle of more than 160° Compact PCB design Pre-soldered 7-pin male header Compatible with Arduino, ESP32, ESP8266, STM32 and Raspberry Pi projects 📋 Technical Specifications Display Type: OLED (Organic Light-Emitting Diode) Display Colour: Blue Display Size: 0.96 inch Driver IC: SSD1306 Resolution: 128 × 64 pixels Interface: SPI / I2C Default Interface: 4-wire SPI Input Voltage: 3.3V–5V Viewing Angle: >160° Module Dimensions: Approximately 27 × 27 × 4mm Operating Temperature: Approximately -30°C to +70°C Header: 7-pin male header, pre-soldered Display Type: Monochrome blue OLED 🔌 7-Pin Interface The 7-pin version provides the following connections: GND – Ground VCC – Power supply D0 / SCK / CLK – SPI clock D1 / MOSI / SDA – SPI data RES / RST – Display reset DC / A0 – Data/Command selection CS – Chip Select 🛠️ SPI Connection The module is normally supplied in 4-wire SPI configuration. For an Arduino Uno, a typical connection is: VCC → 5V GND → GND D0 → SCK / D13 D1 → MOSI / D11 RES → Digital I/O DC → Digital I/O CS → Digital I/O The dedicated CS pin allows the OLED to share the SPI bus with other devices such as SD cards or additional SPI peripherals. 🔄 I2C / IIC Configuration On compatible versions, the module can be converted from SPI to I2C by changing the appropriate resistor configuration on the PCB. The supplied board configuration may require: Moving the resistor from R3 to R1 Shorting R8 with solder Using D0 as SCL Using D1 as SDA Configuring DC for the I2C address The exact resistor positions can vary between board revisions, so check the markings on your particular PCB before modification. 🎯 Applications Arduino projects ESP32 projects ESP8266 projects STM32 development Raspberry Pi projects IoT devices Sensor displays Voltage/current meters Battery monitors Temperature displays Digital clocks Data loggers Portable electronic devices Robotics DIY measuring instruments Embedded systems Menu and status displays 💡 Advantages of OLED OLED technology is self-emissive, meaning the pixels produce their own light and do not require a conventional backlight. This provides high contrast, compact construction and a wide viewing angle while keeping power consumption relatively low. ⚠️ Important Notes This is the 7-pin SPI version, not the 6-pin version. The module is normally configured for SPI communication. Check the PCB labels before connecting the module. Do not exceed the specified supply voltage. Although many versions support 5V operation, the exact voltage tolerance can vary between board revisions. I2C operation may require hardware resistor modification. The actual PCB layout and component markings may vary slightly between production batches. Display colour: Blue. Libraries such as Adafruit SSD1306 and U8g2 can be used with compatible microcontrollers. 📦 Package Includes 1 × 0.96 Inch Blue SPI OLED Display Module
Passive Diaphragm Radiator Speaker Accessories Showcase Speaker Repair Parts
[Passive Radiator] Product Description: Model: 88 48 Low Frequency Vibration Plate Type: Sound film, diaphragm Material: Rubber Size: 88*48mm Net weight: 35 grams The bass radiator is also called a passive speaker. It is used to replace the inverted tube. The subwoofer made with the radiator has the following advantages compared with the traditional inverted subwoofer. The low frequency diving depth is equal to the back type, but the speed is the same. In this sense, it is faster than the inverted type, using the advantage of a certain closed box, and at the same time completely eliminating the disadvantage of the inverted structure-that is, the wind noise brought by the inverted nozzle. Package Includes: 1 x Passive Diaphragm Radiator Speaker Accessories Showcase Speaker Repair Parts
ESP8266 WiFi 5V 1 Channel Relay Module Good Quality
[Relay Module] General Info : Onboard ESP8266 WIFI module, AP mode can be connected at the same time 5 client The module has two ways to work: (i) mobile phone directly mounted on the WIFI module; (ii) mobile phone and WIFI module also carried on the router. How to use : Onboard ESP8266 WIFI module has three operating modes: STA (client), AP (hot), STA + AP (client + hot), according to the work of the module to select the corresponding WIFI module mode of operation The The module needs to use the serial debugging software on the computer and USB to TTL module to send AT commands to configure the WIFI module, USB to TTL module RX, TX, GND pin, then the module on the TX, RX, GND pin, IN +, IN – 5V power supply. Usage Instructions 1) Hardware Connection: Insert the pre-programmed ESP-01/01S module into the onboard 2×4 pin female header (as shown in the diagram below). 2) Power Supply : Connect a DC 5V-12V power source to the module, with the positive terminal to VCC and the negative terminal to GND. 3) Mobile WiFi Connection : Open your phone's WLAN settings, search for and connect to the ESP8266-XXXX hotspot (default password: 12345678). 4) Launch Control APP : Run the pre-installed ESP8266 Controller application on your Android phone. 5) Configure IP Address : Enter the default IP address: 192.168.1.1 in the APP to remotely control the relay switch via your phone. Transmission distance: Open environment, the mobile phone mounted on the WIFI module when the maximum transmission distance of 400m. When the WiFI module and mobile phone at the same time carried on the router when the transmission distance according to the router’s signal weakly; Board function description : IN +, IN-: 5V power input; TX, RX, GND: Serial debug pin; Onboard the ESP8266 WIFI module has three work modes: STA (client), AP (hot), the STA + Ap( hot +client), according to the workings of a module to the corresponding choice of WIFI module working mode. Module need before use serial debugging software and USB to TTL module send serial command was carried out on the WIFI module configuration (don’t power outages after configuration is complete, as some of the parameters of WIFI module cannot be saved when the power is cut off), mobile phone and WIFI module after establishing a network connection can use the phone APP control relay. Control Commands : When cell phone equipped with WiFi module sends commands in the following order: (The default baud rate 115200) AT+CWMODE=2, namely AP mode is selected. AT+RST, reset. AT+CIPMUX=1, open multiple connections. AT+CIPSERVER=1,8080, configure the TCP server, set the port. AT+CIOBAUD=9600 set the baud rate to 9600. (working in relays to control the baud rate 9600). AT+CIFSR to view the AP mode IP address, such as the APIP, “192.168.4.1”. Cell phone WIFI signal connection name starts with AI-THINKER or ESP8266. In the “TCP connection” address and port into the APP, such as 192.168.4.1 and 8080. Click on the grey box relays can be controlled. Features: Onboard Module: ESP8266 wifi module; in AP mode it can connect with 5 Clients at the same time Operating Way: cellphone carried on wifi module; cellphone and wifi module carried on the same router, and use the APP to control relay Diode effusion protection. Short response time
Out of stockTCRT5000 DUAL LINE TRACKING SENSOR MODULE
[IR and PIR Sensors] This IR reflective sensor Module TCRT5000 IR Sensor is used to detect colour and distance. This sensor module consists on an IR transmitter & an IR receiver. IR Transmitter continuously emits IR signal which is then reflected by an obstacle and is then detected by the IR receiver. TCRT5000 Infrared Reflective Sensor Module is often used in line following robots ,object sorting Robot because this module can sense if a surface is white or black. The measuring distance range from 1mm to 8mm, and the central point is about 2.5mm. There is also an on-board potentiometer to adjust the sensitivity. The infrared diode will emitting the infrared continually when the module is powered ON, when the emitted infrared light has not been reflected or the strength is not big enough, the receiver diode will in the off state and output pin i.e. DO will be LOW. Description of Line Tracking sensor TCRT5000L:- Main chip: LM393, Designed with reflected infrared sensor, indicator light. Built in a potentiometer for sensitivity control. On-board LM393 voltage comparator chip and infrared sensing probe TCRT5000L Support 5 V / 3.5 V voltage input On-board signal output instructions, output is high effective signal at the same time, the indicator lamp light output signal can be directly and single-chip microcomputer IO connection & mid dot; Signal detection sensitivity can adjust Reserve all the way more circuits (P3 voltage drawn) using TCRT5000 infrared reflection sensor test reflection distance: 1 mm to 25 mm Operation voltage: 3.5v-5V Operation current: >15mA wide voltage LM393 comparator output form: digital switch output (0 and 1) a fixed bolt hole, convenient installation. Features of Line Tracking sensor TCRT5000:- Product Name : Infrared Obstacle Avoidance Sensor Module; Module Model : TCRT5000; Working Voltage : DC 3.5-5V Output Channel : 0/1; Detect Distance : 1-25mm; Focal Distance : 2.5mm Chipset : LM393; PCB Size : 32 x 14mm/1.3″ x 0.55″ (L*W) Total Size : 38 x 14 x 18mm/1.5″ x 0.55″ x 0.7″(L*W*H); Material : Electric Part Package Content : 1 x Infrared Obstacle Avoidance Sensor Module
Out of stockWS2812B 60LED/mtr 1M DC 5V Addressable LED Strip Roll Non Waterproof 1 Meter Black Strip
[RGB LED Strip] This is WS2812B Addressable LED Strip DC 5V (Non-Waterproof) 60 LEDs/m. The installation surface must be smooth, clean, and dry. The part of LED components cannot be fixed on the surface of the sharp edges. The strip should not be collided or crushed. The strip can be cut following the cutting lines 24-bit colour control (8-bit PWM per channel); 16.8 million colours per pixel. The one-wire digital control interface with each RGB LED draws approximately 50 mA at 5 V with red, green, and blue at full brightness. Choose Quantity – 1m Roll. 1m total length. 60 LEDs/m. 24-bit color control (8-bit PWM per channel). 16.8 million colors per pixel. The one-wire digital control interface. Each RGB LED draws approximately 50 mA at 5 V with red, green, and blue at full brightness. Waterproof. SPECIFICATIONS Voltage 5 V Current 50 mA Approx. colour control 24-bit Length 1m/5m Leds/Meter 60 Max. Power 15W
Out of stock3S 12V 25A 18650 Lithium Battery Protection Board with Balance
[Lithium Battery Protection Board] This is 3S 12V 25A 18650 Lithium Battery Protection Board 11.1V 12.6V High Current With Balanced Circuit Over Charge Over-Discharge Over Current And Short Circuit Protection Function. Board charging and discharging are the same port, the board includes the balanced circuit. When the charge balance, the board will be a bit warm, even after disconnecting the charger, some are still in the balance, will continue to warm for a while until below the equilibrium break threshold. The protection board cannot be used for iron lithium polymer battery (for other batteries, no matter what material, as long as the overvoltage and put voltage can be used for cutting), electric finish machinery, electric bicycle batteries, car, and motorcycle starter battery protection. Applicable to the following products (within rated power): Electric drill, 775 motors (6A-10A), small power inverter, small power vacuum massager battery, LED lamp, 12V standby power electronic products, 12V120W car washing pump, battery, solar street lamp monitoring standby power supply, and other products. Rated current can’t over 25A, it can’t exceed 50A per 0.5 seconds. Specifications : Overcharge voltage range: 4.25-4.35v + 0.05v. Overdischarge voltage range: 2.3-2.7v + 0.05v. Operating current: 0 – 25A. Operating temperature: -40 – +50℃. Instantaneous current: 35 – 40A. Storage condition: -40 – +80℃. Quiescent current: less than 30uA. Balance current: about 40 – 50mA. Effective life: more than 30000 hours. Internal resistance: less than 100m ohm. Short-circuit protection: protection, delayed self recovery. Package includes: 1 x 3S 12V 18650 lithium battery protection board with Balance.
Out of stockATmel MCU ATMEGA16U2 MEGA 2560 R3 Improved Version CH340G Board
[Arduino Boards] The ATmel MCU ATMEGA16U2 MEGA 2560 R3 Improved Version CH340G Board is a micro-controller board base on the ATmega2560. It has a USB host interface to connect with Android based phones, base on the MAX3421e IC. It has 54 digital input/output pins (of which 15 can be used as PWM outputs); 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator; a USB connection, a power jack, an ICSP header, and a reset button. The MEGA ADK is base on the Mega 2560. Similar to the Mega 2560 and Uno, it features an ATmega8U2 program as a USB-to-serial converter. Revision 3 of the Mega ADK board has a resistor pulling the 8U2 HWB line to ground, making it easier to put into DFU(Device Firmware Upgrade) mode. The board has the following new features: 1.0 pin-out: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In the future, shields will be compatible both with the board that uses the AVR, which operate with 5V and with the Arduino Due which operates with 3.3V. The second one is a not connected pin, that is reserved for future purposes. Stronger RESET circuit. The Mega Arduino R3 Android Accessory Development Kit (ADK) can be powered via a USB connection or with an external power supply. The power source is selected automatically. External (non-USB) power can come either from an AC-to-DC adapter (wall-wart) or battery. The adapter can be connected by plugging a 2.1mm centre-positive plug into the board’s power jack. Leads from a battery can be inserted in the GND and Vin pin headers of the POWER connector. Because the Mega R3 Android Accessory Development Kit (ADK) is a USB Host, the phone will attempt to draw power from it when it needs to charge. When the ADK is powered over USB, 500mA total is available for the phone and board. Package Includes : 1 x Mega R3 Android Accessory Development Kit (ADK) board.
Out of stock3S 10A 12V 18650 Lithium Battery Charger Board Protection Module
[Lithium Battery Protection Board] In 3S 10A 12V 18650 Lithium Battery Charger Board Protection Module, 3S stands for 3 18650 batteries or polymer lithium battery series combination. With 10.8V rated voltage for polymer battery, 11.1V 18650 or 3.7V lithium battery rated voltage and 12.6V lithium battery can be charged. And discharge 10A (referring to the maximum discharge current limit) Lithium battery protection board it also Comes with over-charge, over-discharge, over-current, short circuit protection. Formula Expansion : 1C battery expansion, 2000 capacity is equal to 2AH * 1 = 2A upper limit of current. 3C battery expansion, 2000 capacity equal to 2AH * 3 = 6A upper operating current. If the battery gets heat, does not apply that battery, such a situation cannot be long-term use, the battery will soon be damaged. Notes : 1: strictly according to the drawing wiring 0 V (B), 3.7 V (B1), 7.4 V (B2), 11.1 V (B +), not intentionally short circuit! 2: Once you have charged the first line, it will have output. 3: When connecting three battery groups, please make sure that the voltage of each battery group, if not the same, fill each battery separately and then use it in series. discharge test, the fastest battery voltage drop, which group is low battery. (2 good battery + a use effect = 3 low battery low battery use effect). Warning : The protection board can not be used for lithium iron phosphate batteries, lamp hernia, hand drill battery, electric battery fish, electric bicycle battery, car battery for children, 775 (4A) motor, 1 W fish eye LED light, please pay attention customer purchase connection! Described in terms of power for the following products: Massager rechargeable battery, LED ready light power supply, 12 V electronic products, solar street lamp battery, power backup monitor, and other products. Connection Diagram: Package Includes : 1 x 3S 10A 12V 18650 Lithium Battery Charger Board Protection Module.
Out of stockWS2812B Non-Waterproof 144 LED/M Addressable Pixel Strip for Arduino 5 METER
[RGB LED Strip] This is WS2812B Addressable LED Strip DC 5V (Non-Waterproof) 144 LEDs/m. The installation surface must be smooth, clean, and dry. The part of LED components cannot be fixed on the surface of the sharp edges. The strip should not be collided or crushed. The strip can be cut following the cutting lines 24-bit color control (8-bit PWM per channel); 16.8 million colors per pixel. The one-wire digital control interface with each RGB LED draws approximately 50 mA at 5 V with red, green, and blue at full brightness Package Includes :- 5 Meter WS2812B 144 Pixel Strips.
WS2812B 60LED/mtr 5M DC 5V Addressable LED Strip Roll Non Waterproof 5 Meter
[RGB LED Strip] This is WS2812B Addressable LED Strip DC 5V (Non-Waterproof) 60 LEDs/m. The installation surface must be smooth, clean, and dry. The part of LED components cannot be fixed on the surface of the sharp edges. The strip should not be collided or crushed. The strip can be cut following the cutting lines 24-bit colour control (8-bit PWM per channel); 16.8 million colours per pixel. The one-wire digital control interface with each RGB LED draws approximately 50 mA at 5 V with red, green, and blue at full brightness. Choose Quantity – 5m Roll. 5m total length. 60 LEDs/m. 24-bit color control (8-bit PWM per channel). 16.8 million colors per pixel. The one-wire digital control interface. Each RGB LED draws approximately 50 mA at 5 V with red, green, and blue at full brightness. Waterproof. SPECIFICATIONS Voltage 5 V Current 50 mA Approx. colour control 24-bit Length 1m/5m Leds/Meter 60 Max. Power 15W