All products · 75 of 1440
Electronics, sensors, robotics kits, PC components, peripherals — everything Unik Systems carries, in one place.
Quarky
Educational STEM controller board. USB programmable. Block coding + Python/Arduino-like. Built-in sensors (mic, light, IMU) + ports for external sensors/servos. 5V input (USB/power bank). BLE/Wi-Fi optional depending on version.
USB to DC Jack Cable
USB to DC jack cable, useful for power-bank-driven projects.
Out of stockPower Bank 10000 mAh USB-C PD 20W
Slim 10000 mAh power bank, USB-C PD 20W in/out + USB-A QC 3.0.
Out of stockPower Bank 20000 mAh 65W (Laptop)
Laptop-capable 20000 mAh, USB-C PD 65W, dual output, LED display.
2S 4A Type-C Lithium Battery Charging Module – 8.4V Step-Up Boost Charger for 18650 Lipo
[Step UP Buck Converter] 2S 4A Type-C Lithium Battery Charging Module – 8.4V Step-Up Boost Charger for 18650 The 2S 4A Type-C Lithium Battery Charging Module is a compact step-up charging board designed for charging 2-cell series (2S) 18650 Li-ion/Li-Po battery packs. It accepts a 3–6V DC input through USB Type-C and boosts the voltage to 8.4V, the required full-charge voltage for a 2S lithium battery pack. The 4A specification refers to the maximum input current version. According to available product specifications, the corresponding charging current is approximately 2.2A, rather than 4A. ⭐ Key Features Designed for 2S lithium-ion/Li-Po battery packs Suitable for 2 × 18650 cells connected in series USB Type-C input 3–6V DC input Recommended input: 3.7V / 5V Step-up/boost charging circuit 8.4V charging voltage 4A maximum input-current version Approximately 2.2A charging current Automatic recharge function Battery charging protection features Compact PCB design LED charging/status indication Suitable for DIY battery and portable-power projects 📋 Technical Specifications Product Type: 2S Lithium Battery Step-Up Charging Module Battery Configuration: 2S – 2 cells in series Compatible Battery: 3.6V/3.7V Li-ion / Li-Po Nominal Battery Pack Voltage: 7.4V Full-Charge Voltage: 8.4V Input Voltage: DC 3–6V Recommended Input: DC 3.7V / 5V Maximum Input Current: 4A Charging Current: Approximately 2.2A Charging Interface: USB Type-C Charging Mode: Constant-current / constant-voltage Board Size: Approximately 39 × 18 × 6.3mm Operating Temperature: -40°C to +85°C LED Indicators: Charging / fully charged or constant-voltage status 🔋 Charging Performance For the 2S 4A version: USB Type-C 5V → Boost Charging Module → 8.4V → 2S Battery Pack The module draws up to approximately 4A from the input, while the specified charging current is approximately 2.2A. This distinction is important when selecting the USB power adapter. 🔧 Applications 2S 18650 battery packs 7.4V Li-ion battery packs 2S Li-Po battery packs DIY power banks Portable electronics Bluetooth speaker battery systems Robotics projects Solar charging applications Electronic prototyping Portable audio equipment Electric fan projects Type-C rechargeable equipment Custom battery charging systems 🛠️ How It Works The module uses a boost/step-up charging circuit to convert the lower USB Type-C input voltage into the 8.4V charging voltage required for a 2S lithium battery pack. Example: 5V Type-C Input → Step-Up Circuit → 8.4V Charging Output → 2S 18650 Battery A 2S battery pack consists of two lithium cells connected in series: 3.7V + 3.7V = 7.4V nominal4.2V + 4.2V = 8.4V fully charged 💡 LED Indicators The module uses status indicators to show the charging condition: CR: Charging OK: Fully charged / constant-voltage stage ⚠️ Important Notes This module is intended for 2S battery packs only. Do not connect a single 18650 cell directly to the 8.4V charging output. The two cells should be properly matched and in good condition. Do not exceed the 6V maximum input voltage. A suitable Type-C power source is required to supply the necessary input current. The 4A rating is the input-current rating, not the battery charging current. The specified charging current for this 2S 4A version is approximately 2.2A. This charging module should not automatically be considered a replacement for a dedicated 2S BMS/protection board. Use appropriate battery protection where required. Check the PCB polarity and connection markings before connecting the battery. Do not short-circuit the input or output. Use properly matched lithium cells for safe and reliable charging. Keep the module adequately ventilated during higher-current operation. 📦 Package Includes 1 × 2S 4A Type-C Step-Up Boost Lithium Battery Charging Module – 8.4V
Type-C PD/QC/AFC Fast Charge Decoy Trigger Module – 5V/9V/12V/15V/20V Fixed Output
[Step UP Buck Converter] Type-C PD/QC/AFC Fast Charge Decoy Trigger Module – 5V/9V/12V/15V/20V Fixed Output The Type-C PD/QC/AFC Fast Charge Decoy Trigger Module is a compact USB Type-C power negotiation module designed to request a selected voltage from compatible USB Type-C fast chargers and power banks. It supports QC 2.0/3.0, AFC, PD 2.0 and PD 3.0 protocols, allowing compatible USB-C power sources to provide higher voltage outputs such as 5V, 9V, 12V, 15V or 20V. This module is useful for DIY electronics projects where a USB Type-C PD/QC charger needs to be used as a DC power source for equipment that does not have native USB-C fast-charging support. ⭐ Key Features USB Type-C fast-charge decoy/trigger module Supports PD 2.0 / PD 3.0 Supports QC 2.0 / QC 3.0 Supports Samsung AFC Fixed selectable voltage output Supports 5V / 9V / 12V / 15V / 20V output options Negotiates the required voltage from a compatible charger Suitable for USB-C power banks and PD adapters LED indicators for operating/status indication Compact and lightweight PCB design Useful for DIY power supply and electronics projects Plug-and-play operation with compatible USB-C power sources 📋 Technical Specifications Product Type: USB Type-C Fast Charge Trigger / Decoy Module Input Connector: USB Type-C Input Source: USB-C PD/QC/AFC compatible charger or power bank Supported Protocols: PD2.0, PD3.0, QC2.0, QC3.0, AFC Output Voltage: 5V / 9V / 12V / 15V / 20V Output Type: DC Voltage Selection: Fixed/selectable depending on module version Indicator: LED status indicators Application: DC power conversion and fast-charge voltage triggering 🔧 Applications Converting USB-C PD chargers into DC power supplies Powering DIY electronics projects Arduino and microcontroller projects LED applications Portable electronic equipment DIY laboratory power supplies DC motors and other suitable loads Router/modem power applications where the required voltage matches Powering electronics from USB-C PD power banks Replacing conventional DC adapters with USB-C PD sources 🛠️ How It Works The module does not boost the USB voltage itself. Instead, it communicates with a compatible USB-C power source and sends the required PD/QC/AFC negotiation request. For example, when connected to a compatible PD charger, the module can request: 5V → 9V → 12V → 15V → 20V The charger then provides the negotiated voltage at the module's DC output. ⚠️ Important Notes The connected USB-C charger or power bank must support the required fast-charging protocol and voltage. A standard 5V-only USB charger cannot normally provide 9V/12V/15V/20V through this module. Always verify the selected output voltage with a multimeter before connecting your device. Do not connect a device that requires a lower voltage than the selected output. The module is a trigger/decoy board, not a standalone DC-DC boost converter. Maximum available output power/current depends on the connected USB-C charger/power bank and the module's specifications. Do not short the output terminals. 20V output can damage 5V/9V/12V-only electronics if the wrong voltage is selected. Exact selectable voltages and current capability can vary between board versions. 📦 Package Includes 1 × Type-C PD/QC/AFC Fast Charge Decoy Trigger Module
Digital USB Mobile Power Charging Current Voltage Tester Meter
[Ammeter and Voltmeter] Digital USB Mobile Power Charging Current Voltage Tester Meter The Digital USB Mobile Power Charging Current Voltage Tester Meter is a compact USB testing device designed to measure and display charging voltage and current in real time. It is useful for checking the power output of USB chargers, power banks and other USB-powered devices. ⭐ Key Features Precise current and voltage measurement Simultaneous voltage and current display Bright digital LCD display Straight USB connector design USB Type-A Male input and USB Type-A Female output Compact and lightweight Easy to connect and use Suitable for USB chargers and power banks Compatible with USB-powered devices 📋 Technical Specifications Product Name: Digital USB Mobile Power Charging Current Voltage Tester Meter Color: As per available stock Input Voltage: 3.5V–7.0V Output Voltage: 3.5V–7.0V Current Measurement Range: 0A–3A Voltage Accuracy: ±1% Current Accuracy: ±1% Display Type: Digital LCD Display Screen Size: 0.91 inch Data Display: Voltage and Current simultaneously Power Consumption: ≤0.1W Interface: USB Type-A Male (Input) / USB Type-A Female (Output) Measurement Frequency: 2 times per second Operating Temperature: 0°C–45°C Material: ABS Plastic Dimensions: 64 × 23 × 15mm Weight: 15g Compatibility: USB-powered devices 🔧 Applications Mobile charger testing USB charger testing Power bank testing USB power supply testing Mobile phone charging analysis USB device testing Electronics troubleshooting DIY electronics projects Checking charging voltage and current 🛠️ How to Use Insert the USB Type-A Male connector into the USB charger, power bank or USB power source. Connect the USB-powered device to the USB Type-A Female output. The digital display will show the voltage and charging current. Monitor the readings during charging or testing. 📦 Package Includes 1 × Digital USB Mobile Power Charging Current Voltage Tester Meter ⚠️ Important Notes Do not exceed the specified voltage and current measurement ranges. This tester is intended for USB/DC applications. Actual readings may vary depending on the charger, cable and connected device. Use within the specified operating temperature range.
KWS-MX18 10-in-1 USB Tester Digital LCD Voltage, Current & Power Meter
[Ammeter and Voltmeter] KWS-MX18 10-in-1 USB Tester – Digital LCD Voltage, Current & Power Meter The KWS-MX18 10-in-1 USB Tester is a compact multifunction digital testing instrument designed for monitoring and evaluating USB chargers, power banks, USB ports, mobile charging systems, and other DC power sources. It provides real-time measurement of voltage, current, power, capacity, energy, charging time, resistance, and internal temperature on its digital display. The tester supports a DC voltage range of 4–30V and current measurement up to approximately 5.1A, with power measurement up to 150W. It also provides capacity and energy monitoring, making it useful for checking the actual charging performance and capacity of USB power supplies and power banks. ⭐ Key Features 10-in-1 multifunction USB tester Digital LCD display Real-time voltage and current monitoring Measures power consumption Measures accumulated charging capacity Measures energy consumption Charging time measurement Charging resistance measurement Internal temperature measurement Positive and negative voltage measurement Stores measurement data in 9 groups Power-off memory function Compact and lightweight design Suitable for USB charger and power-bank testing Supports QC2.0 / QC3.0 according to available product information 📋 Technical Specifications Product Type: 10-in-1 USB Digital Tester Model: KWS-MX18 Input Voltage Range: DC 4–30V Current Measurement: 0–5.1A Power Measurement: 0–150W Capacity Measurement: 0–999999mAh Energy Measurement: 0–999999mWh Timing Range: 0–99 Hours Charging Resistance: 0–999.9Ω Internal Temperature: 0–80°C Positive Voltage Measurement: 0–10V Negative Voltage Measurement: 0–10V Memory Groups: 1–9 Display: Digital LCD Material: ABS Dimensions: Approximately 56.6 × 24.7 × 11.2mm Weight: Approximately 13.9g Input Connector: USB Output Connector: USB Function Button: Yes 🔍 10 Measurement Functions Voltage: 4–30V DC Current: 0–5.1A Power: 0–150W Capacity: 0–999999mAh Energy: 0–999999mWh Charging Time: 0–99 hours Charging Resistance: 0–999.9Ω Positive Voltage: 0–10V Negative Voltage: 0–10V Internal Temperature: 0–80°C 💾 Memory Function The KWS-MX18 can store charging measurement information in 9 separate memory groups. This allows you to compare charging capacity and energy measurements from different chargers or devices. The stored data can be viewed using the function button, and an individual memory group can be cleared by holding the button for approximately 3 seconds. 🔘 Button Functions Single Press: View stored measurement data from memory groups 1–9. Long Press: Clear the currently selected memory group. Double Press: Change the display page. Calibration: The device supports voltage and current calibration according to the supplied manual. 🔌 Applications USB Charger Testing Mobile Charger Testing Power Bank Testing USB Port Testing Mobile Phone Charging Analysis USB Cable Testing Power Supply Monitoring DC Power Measurement Electronics Troubleshooting DIY Electronics Projects Charger Performance Testing Battery Charging Analysis 🛠️ How to Use Connect the KWS-MX18 in-line between the USB power source and the USB-powered device. Once powered, the LCD displays the measured electrical parameters. You can use the function button to change display pages and access stored measurement data. It is particularly useful for comparing chargers, power banks, cables, and USB ports by monitoring actual voltage, current, power, capacity, and energy delivered. 📦 Package Includes 1 × KWS-MX18 10-in-1 USB Digital Tester ⚠️ Color Note: Color: White / Black Color will be shipped depending on stock availability. Any one color (White or Black) may be shipped based on available stock. Specific color cannot be guaranteed. ⚠️ Precautions Do not exceed the specified 30V DC input voltage. Do not exceed the specified current measurement range. Ensure correct USB connection direction before use. Keep the tester away from water and excessive moisture. Do not use it for measuring mains AC voltage. The device is intended for DC/USB power measurement. Actual measurement accuracy can depend on the connected source, load, cable, and operating conditions.
Winway 18650 Lithium-Ion Rechargeable Battery 3.7V 2600mAh 9.62Wh
[Lithium Battery Cell] The Winway 18650 Lithium-Ion Rechargeable Battery is a high-performance cylindrical Li-ion cell designed to deliver reliable and long-lasting power for a wide range of electronic devices. With a nominal voltage of 3.7V, 2600mAh capacity, and 9.62Wh energy rating, it provides consistent power output for both high-drain and low-drain applications. Manufactured using premium lithium-ion cell technology, this battery offers excellent energy density, stable discharge performance, and long cycle life. Its standard 18650 form factor makes it compatible with most battery holders, chargers, and devices designed for 18650 cells. The Winway 2600mAh battery is widely used in rechargeable flashlights, emergency lights, battery packs, power banks, Bluetooth speakers, portable fans, solar lighting, DIY electronics, robotics, and various battery-operated devices. Designed for durability and dependable performance, this battery delivers excellent backup time while maintaining stable voltage throughout the discharge cycle. ⭐ Features High-quality 18650 Lithium-Ion rechargeable battery 2600mAh high-capacity cell Nominal voltage of 3.7V Energy rating of 9.62Wh Stable discharge performance High energy density Long charge and discharge cycle life Lightweight and compact cylindrical design Suitable for battery pack assembly Compatible with standard 18650 battery holders and chargers 📋 Technical Specifications Product Type: Lithium-Ion Rechargeable Battery Brand: Winway Battery Model: 18650 Nominal Voltage: 3.7V Nominal Capacity: 2600mAh Energy: 9.62Wh Battery Chemistry: Lithium-Ion (Li-ion) Cell Type: Rechargeable Form Factor: Cylindrical 18650 Diameter: Approx. 18mm Length: Approx. 65mm Weight: Approx. 45g Color: Green Rechargeable: Yes Made In: India Pack Quantity: 1 Piece 🔧 Applications Suitable for: Rechargeable Flashlights Emergency Lights Power Banks Bluetooth Speakers Portable Fans Solar Lighting Systems DIY Battery Packs Robotics Projects Arduino Projects ESP32 Projects Electronic Toys Portable Electronic Devices Medical Equipment (Compatible Models) Industrial Electronic Equipment 📦 Package Includes 1 × Winway 18650 Lithium-Ion Rechargeable Battery 3.7V 2600mAh ⚠️ Safety Instructions Use only a compatible Li-ion battery charger. Do not short-circuit, puncture, crush, or disassemble the battery. Do not expose the battery to fire, excessive heat, or water. Observe correct polarity during installation. Do not overcharge or over-discharge the battery. Store in a cool, dry place away from direct sunlight.
10-in-1 USB & Type-C Digital Tester – IPS Voltmeter, Ammeter, Impedance & Capacity Meter
[Ammeter and Voltmeter] The 10-in-1 USB & Type-C Digital Power Tester is a multifunction USB measurement instrument developed for engineers, technicians, hobbyists, and electronics enthusiasts. It accurately monitors USB charging performance while providing comprehensive electrical measurements for USB-A and USB Type-C devices. Equipped with a bright IPS true-color LCD display, the tester simultaneously displays ten important charging parameters including Voltage, Current, Power, Capacity (mAh), Energy (mWh), Cable Resistance, Temperature, Charging Time, D+ Voltage, and D− Voltage. The tester features both USB-A and USB Type-C input/output interfaces, allowing compatibility with traditional USB chargers as well as modern USB-C Power Delivery devices. It supports testing of fast chargers, mobile phones, tablets, laptops, power banks, USB cables, and various USB-powered electronics. With support for measurements up to 150W and 5A, this tester is suitable for high-power USB-C PD chargers while consuming less than 20mA of operating current. Built-in control buttons allow users to switch display modes, perform fast-charge diagnostics, and manage measurement functions easily. Its compact design makes it an excellent tool for electronics repair, charger verification, cable testing, battery capacity measurement, laboratory work, and DIY electronics projects. 🔹 Key Features Dual Interface: USB-A & USB Type-C Input/Output Supports USB PD and Fast Charging IPS Full Color LCD Display Measures Voltage, Current and Power Capacity (mAh) & Energy (mWh) Measurement Cable Resistance (Impedance) Measurement Internal Temperature Monitoring USB D+ / D− Voltage Detection Charging Timer Function High Accuracy Measurement Low Self Power Consumption Compact Portable Design Easy Operation with Dedicated Function Buttons 🔹 Technical Specifications Product Type: USB Digital Power Tester Display: IPS True Color LCD Input Interface: USB-A / USB Type-C Output Interface: USB-A / USB Type-C Maximum Power Measurement: 150W Maximum Current: 5A Voltage Measurement: USB Standard & USB-C PD Power Measurement Range: 0–150W Current Measurement: Up to 5A Capacity Measurement: mAh Energy Measurement: mWh Impedance Measurement Range: 1–999.9Ω Temperature Measurement: 0°C to 80°C USB D+ Voltage Range: 0–2.99V USB D− Voltage Range: 0–2.99V Timer Range: 999 Hours 59 Minutes Refresh Rate: Approximately 500ms Self Power Consumption: <20mA Operating Buttons: Mode / Power Dimensions: 76.9 × 38 × 11 mm 🔹 Applications This USB tester is suitable for: USB charger testing USB-C PD charger testing Power bank capacity testing Mobile charger verification Fast charging protocol diagnostics USB cable resistance testing Laptop USB-C charger testing Electronics repair DIY electronics projects Laboratory measurements Battery charging analysis Quality inspection of USB power supplies 🔹 Package Includes 1 × 10-in-1 USB & Type-C Digital Power Tester 🔹 Frequently Asked Questions (FAQ) What does "10-in-1" mean? It measures ten important parameters: Voltage, Current, Power, Capacity, Energy, Impedance, Temperature, Charging Time, D+ Voltage, and D− Voltage. Does it support both USB-A and USB Type-C? Yes. It features both USB-A and USB Type-C input and output interfaces. What is the maximum power it can measure? Up to 150W. What is the maximum current supported? Up to 5A. Can it test USB-C laptop chargers? Yes. It supports high-power USB-C PD chargers up to 150W. Can it measure charging cable quality? Yes. It measures cable impedance from 1Ω to 999.9Ω. Does it display temperature? Yes. It includes an internal temperature sensor with a range of 0°C to 80°C. Does it require batteries? No. It is powered directly from the connected USB source. Can it measure power bank capacity? Yes. It records charging capacity in mAh and mWh. Does it support fast charging protocols? Yes. It can monitor USB D+ and D− voltages, helping identify fast charging protocol handshakes.
Micro USB 5V 1A Step-Up Boost Converter Power Bank Charging Module for 3.7V Lithium Battery
[Li-ion Rechargeable Battery Charger, Lithium Battery Protection Board] The Micro USB 5V 1A Step-Up Boost Converter Power Bank Charging Module is a versatile and reliable solution for building portable power banks and battery-powered electronic projects. Designed for use with a single 3.7V lithium-ion battery, the module integrates battery charging, protection circuitry, and a high-efficiency boost converter on a single compact PCB. In addition, the onboard boost converter efficiently converts the battery voltage to a regulated 5V USB output, making it suitable for charging smartphones, microcontroller projects, portable gadgets, and USB-powered devices. As a result, users can create compact and dependable portable power solutions with minimal external components. Because of its integrated protection functions, the module safeguards the battery against overcharging, over-discharging, and short circuits. Furthermore, LED status indicators provide clear visual feedback regarding charging and operating conditions. The compact design allows easy integration into custom battery packs, DIY power banks, portable electronics, and embedded systems. Moreover, the Micro USB charging interface ensures compatibility with widely available charging cables and adapters. 🔹 Key Features Micro USB charging interface Integrated lithium battery charging circuit Built-in 5V step-up boost converter Stable 5V USB output Supports single-cell 3.7V lithium-ion batteries Overcharge protection Over-discharge protection Short-circuit protection High conversion efficiency LED charging status indicators Compact and lightweight design 🔹 Technical Specifications Product Type: Power Bank Charging Module Charging Interface: Micro USB Input Voltage: 3.7V Lithium Battery Output Voltage: 5V USB Standard Maximum Output Current: 1A Supported Battery Type: Single Cell Lithium-Ion Battery (3.7V) Efficiency: Up to 92% Quiescent Current: Less than 100µA Charging Protection: Overcharge, Over-discharge, Short Circuit Protection Overcharge Protection Voltage: 4.2V Over-discharge Protection Voltage: 2.5V Charging Cut-off Current: 50mA Module Dimensions: Approx. 36mm × 17mm × 7mm PCB Thickness: 1.6mm Operating Temperature: -40°C to +85°C Status Indication: LED Charging Indicators 🔹 Applications This charging module is suitable for: DIY power banks Portable USB chargers Lithium battery projects Arduino power supplies ESP32 and IoT devices Portable electronics Rechargeable battery systems USB-powered gadgets 🔹 Package Includes 1 × Micro USB 5V 1A Step-Up Boost Converter Lithium Battery Charging and Protection Module
3.7V BMS 1S 2A 18650 Lithium Battery Protection Board
[Lithium Battery Protection Board] The 1S 3.7V Lithium Battery Protection Board (BMS/PCM) is a compact battery management module designed specifically for single-cell lithium-ion batteries such as 18650, 14500, and similar 3.7V rechargeable cells. It continuously monitors battery voltage and current to ensure safe charging and discharging operations. In addition, the module provides multiple layers of protection including overcharge, over-discharge, overcurrent, and short-circuit protection. As a result, it helps extend battery life and improves the safety of battery-powered devices. Because of its compact size, the protection board can be easily integrated into DIY battery packs, portable electronics, LED lighting systems, and rechargeable battery projects. Furthermore, the board uses nickel-strip compatible terminals for easy battery pack assembly. The protection circuit is designed for long-term reliable operation and helps prevent damage caused by improper charging or excessive current draw. Moreover, it offers high voltage detection accuracy for improved battery management performance. ⚠️ Note: This protection board is designed for 3.7V Lithium-Ion batteries only and is not suitable for LiFePO4 batteries. 🔹 Key Features Single-cell (1S) lithium battery protection board Suitable for 18650 lithium-ion batteries Overcharge protection Over-discharge protection Overcurrent protection Short-circuit protection High voltage detection accuracy Compact and lightweight design Easy installation and integration Long operational life 🔹 Pin Configuration B+ : Battery Positive Terminal B- : Battery Negative Terminal P+ : Charge / Discharge Positive Terminal P- : Charge / Discharge Negative Terminal 🔹 Technical Specifications Product Type: Lithium Battery Protection Module (BMS/PCM) Battery Configuration: 1S (Single Cell) Compatible Battery Type: 3.7V Lithium-Ion (18650, 14500, etc.) Operating Voltage Range: 3.2V – 4.2V Overcharge Detection Voltage: 4.25 ± 0.05V Overcharge Release Voltage: 4.23 ± 0.05V Over-discharge Detection Voltage: 2.54 ± 0.1V Continuous Charge Current: 2A Continuous Discharge Current: 2A Maximum Supported Current: 2A – 5A Protection Functions: Overcharge, Over-discharge, Overcurrent, Short Circuit Terminal Type: Nickel Strip Compatible Board Life Expectancy: More than 20,000 Operating Hours 🔹 Applications This protection board is suitable for: 18650 battery packs Rechargeable lithium battery projects DIY power banks Portable electronics LED lighting systems Battery-powered devices Robotics projects Arduino and ESP32 power systems 🔹 Important Notes Not suitable for LiFePO4 batteries Not recommended for high-current motors above 4A Not suitable for electric bicycles or high-power battery packs Ensure correct polarity during installation Use only with compatible lithium-ion cells 🔹 Package Includes 1 × 1S 3.7V 2A Lithium-Ion Battery Protection Board (BMS/PCM)
TP4056 1A Li-Ion Lithium Battery Charging Module with Micro USB 3.7V Charger Board
[Li-ion Rechargeable Battery Charger, Lithium Battery Protection Board] The TP4056 1A Li-Ion Lithium Battery Charging Module – Micro USB is a compact and efficient charging board designed for charging single-cell 3.7V lithium-ion and lithium polymer batteries. It features an onboard Micro USB connector, allowing direct charging from USB power sources such as computers, adapters, and power banks. In addition, the module supports external power input through the IN+ and IN- pads, making it suitable for custom battery charging applications and DIY electronics projects. As a result, users can easily integrate the module into portable devices and battery-powered systems. Because of its compact size and lightweight design, the TP4056 module is ideal for space-limited applications. Furthermore, the onboard charging management IC provides stable charging performance with high accuracy and reliable battery protection. The charging current is set to 1A by default, but it can also be adjusted by changing the onboard programming resistor. Moreover, the module includes dual LED indicators for charging status and full-charge indication. This charging module is widely used in power banks, DIY battery chargers, portable electronics, IoT devices, robotics systems, and rechargeable battery projects. 🔹 Key Features TP4056 lithium battery charging IC Onboard Micro USB input interface Suitable for 3.7V Li-Ion and LiPo batteries Default 1A charging current Adjustable charging current support Dual LED charging status indicators Compact and lightweight design High charging accuracy and stable performance Easy integration into DIY projects 🔹 Technical Specifications Product Type: Lithium Battery Charging Module Charging IC: TP4056 Input Interface: Micro USB Input Voltage: 5V DC Battery Type: 3.7V Li-Ion / LiPo Battery Default Charging Current: 1A Adjustable Current Range: 100mA – 1000mA Charging Method: Constant Current / Constant Voltage Charging Indicators: Charging LED & Full Charge LED Mounting Type: PCB Module Body Material: FR4 PCB 🔹 Applications This TP4056 charging module is suitable for many electronic applications, including: DIY power banks Rechargeable battery projects Portable electronics Robotics systems IoT devices Battery charging circuits Arduino projects DIY electronics projects 🔹 Package Includes 1 × TP4056 1A Li-Ion Lithium Battery Charging Module – Micro USB
TC4056 Type-C 1A Lithium Battery Charging Module 5V USB-C 3.7V Li-ion LiPo Charger Board
[Li-ion Rechargeable Battery Charger, Lithium Battery Protection Board] Product Description The TC4056 Type-C Lithium Battery Charging Module is a compact, efficient, and reliable solution for charging 3.7V lithium-ion and lithium polymer batteries. Designed with a modern USB Type-C input, this module ensures easy compatibility with standard chargers and power sources. It uses a proven CC/CV (Constant Current / Constant Voltage) charging algorithm, which ensures safe charging, longer battery life, and stable performance. The module is ideal for DIY electronics, power banks, portable devices, and embedded systems. With intelligent charging management, automatic cut-off, and pre-charge functionality, the TC4056 module provides complete protection and efficient charging for your batteries. ⚡ Key Features 🔋 Safe & Efficient CC/CV ChargingProvides stable and optimized charging for lithium batteries. 🔌 Type-C USB InputEasy to use with mobile chargers, USB adapters, and power banks. ⚡ Stable 1A Charging CurrentDefault charging current of 1A for fast and reliable performance. 🔴🔵 LED Charging Indicators Red LED: Charging Blue LED: Fully Charged 🧩 Compact & Lightweight DesignPerfect for space-constrained and portable applications. 🛠️ Easy IntegrationSimple connections make it beginner-friendly and ideal for DIY use. 🔄 Smart Charging Features 🔋 Automatic Charge TerminationStops charging when current drops to 100mA after full charge, protecting battery health. 🔄 Auto Recharge FunctionCharging restarts automatically when battery voltage falls below 4.05V. 🪫 Pre-Charge ModeWhen battery voltage is below 2.9V, the module charges safely at 100mA. 📊 Specifications Specification Description Charging IC TC4056 Input Voltage 5V DC (Type-C USB) Charging Current 1A (default, adjustable) Battery Type 3.7V Li-ion / Li-Po Cut-off Voltage 4.2V Charging Method CC/CV Indicators Red (Charging), Blue (Full) 🔧 Applications 🔋 18650 Battery Charging🔌 DIY Power Banks🔧 Arduino / ESP32 Projects🎮 Portable Electronics💡 Rechargeable LED Projects📦 Backup Power Systems 📦 Package Includes 1 × TC4056 Type-C Lithium Battery Charging Module
Type-C USB 5V 2A Step-Up Boost Converter with USB Charger
[Li-ion Rechargeable Battery Charger, Step UP Buck Converter] Build your own portable power solutions with the Type-C USB 5V 2A Step-Up Boost Converter Power Bank Module — a compact and efficient charging solution designed for DIY power banks and USB-powered devices. This versatile module supports battery charging and 5V boost output, allowing you to convert battery voltage into a stable 5V USB output for powering smartphones, microcontrollers, and other USB devices. Equipped with a Type-C input, high-efficiency boost circuit, and intelligent power management, this module ensures reliable performance, fast charging, and safe operation. It also supports simultaneous charging and discharging, making it perfect for uninterrupted power supply applications. Key Features 🔋 2-in-1 Charging + Boost ModuleCharge your lithium battery while simultaneously providing a stable 5V output. ⚡ Stable 5V 2A OutputDelivers consistent power for USB devices like smartphones, Arduino, ESP32, and more. 🔌 Type-C USB InputModern and widely compatible input for easy charging (5V–5.5V). 🔄 High Efficiency Boost Conversion (Up to 92.5%)Minimizes power loss and improves battery life. 🧠 Smart Power ManagementAutomatically controls charging cycles, output switching, and battery protection. 🔘 External Button Control Support Short press: Turn ON output & display Double press: Turn OFF output 🔧 DIY Friendly DesignIncludes USB-A solder pads for custom builds and integrations. Working Functions 🔹 Auto shutdown when load current < 50mA🔹 Auto stop charging when current drops to 100mA🔹 Auto recharge when battery voltage < 4.1V🔹 Pre-charge mode below 2.8V (180mA safe charging)🔹 Supports charging while discharging Specifications Specification Description Input Voltage 5V – 5.5V (Type-C USB) Charging Cut-off Voltage 4.2V / 4.35V ±0.5% Charging Current 2.4A ±5% Boost Output Voltage 5V – 5.15V Output Current Up to 2A Efficiency Up to 92.5% Output Ripple 100mV Quiescent Current 30µA Material Metal + Plastic Applications 🔋 DIY Power Banks📱 Mobile Charging Projects🔧 Arduino / ESP32 Power Supply🔌 USB Device Power Modules🚗 Portable Electronics🧪 Embedded Systems & Prototyping Package Includes 1 × Type-C USB 5V 2A Step-Up Boost Converter Power Bank Module
3.7V 4.2V Battery Type-C Charger Board DC-DC Step-Up Boost Module
[Lithium Battery Protection Board] The 3.7V 4.2V Battery Type-C Charger Board DC-DC Step-Up Boost Module is a compact power management module designed for single lithium batteries. It combines a charging circuit and a DC-DC step-up boost converter, allowing the battery to power devices that require higher voltage outputs. This module uses a USB Type-C interface, which provides convenient and reliable power input. As a result, it is compatible with many modern power adapters and USB chargers. In addition, the onboard boost circuit can increase the battery voltage and deliver stable output. Because of this feature, the module can power small electronics such as portable gadgets, DIY power banks, and IoT devices. The board also includes several protection functions. For example, it protects the battery from over-charging, over-discharging, short circuits, and overheating. Therefore, the battery can operate safely and maintain a longer service life. Thanks to its ultra-small and lightweight design, the module is easy to integrate into compact electronic devices and DIY electronics projects. 🔹 Key Features Supports lithium battery charging and discharging USB Type-C power input Integrated DC-DC step-up boost converter Adjustable boost output voltage Constant current and constant voltage charging Built-in over-temperature protection Charging status and fault indicator Ultra-compact and lightweight design 🔹 Technical Specifications Parameter Specification Chipset TP4056 Input Voltage 4.2V – 5.5V Output Voltage 4.2V – 24V Adjustable Maximum Power 5W Operating Temperature -40°C to 80°C Operating Humidity 5% – 95% RH Module Size 23.4 × 18 mm Weight ~5 g 🔹 Applications This module can be used in many portable electronics projects, such as: DIY power banks Portable electronics IoT devices Robotics projects Emergency backup power systems Battery-powered gadgets 🔹 Package Includes 1 × 3.7V 4.2V Battery Type-C Charger Board DC-DC Step-Up Boost Module
Super Mini 3.7V 4.2V Type-C USB Lithium Battery Charging Module with Protection
[Li-ion Rechargeable Battery Charger] The Super Mini Type-C Lithium Battery Charging Module is a small and efficient charging board for 3.7V lithium batteries. It accepts 5V input through a Type-C USB connector and charges the battery safely up to 4.2V. In addition, the module includes a built-in protection circuit. This circuit protects the battery from overcharging, deep discharge, and short circuits. As a result, the battery remains safe during charging and everyday use. Because of its very compact size, the module easily fits into small electronic devices. For example, it can be used in Bluetooth speakers, IoT devices, portable electronics, and DIY battery projects. Moreover, the board is easy to install and requires only simple wiring connections. Therefore, it is widely used in DIY electronics, robotics projects, and small battery-powered gadgets. 🔹 Key Features Supports 3.7V lithium-ion batteries Type-C USB input for convenient charging Standard 4.2V charging voltage Built-in protection circuit Compact and lightweight design Easy wiring and installation Automatic charge cutoff for safety 🔹 Technical Specifications Parameter Specification Battery Type 3.7V Lithium-ion Input Voltage 5V (Type-C USB) Charging Voltage 4.2V Charging Current Up to 1A Protection Overcharge / Over-discharge / Short circuit Connector Type-C USB Board Type Lithium battery charging module 🔹 Applications This charging module is suitable for many portable devices. For example: DIY power banks Bluetooth speakers IoT and smart devices Robotics projects Portable electronics Small lithium battery packs 🔹 Package Includes 1 × Super Mini 3.7V 4.2V Type-C USB Lithium Battery Charging Module with Protection
Out of stock803040 3.7V 1000mAh LiPo Battery | Rechargeable Lithium Polymer Battery Cell
[LiPo Cell] The 803040 3.7V 1000mAh Lithium Polymer Battery is a lightweight and compact rechargeable battery designed for portable electronic devices and embedded applications. With a stable 3.7V nominal voltage and 1000mAh capacity, it provides reliable power for IoT projects, DIY electronics, Bluetooth devices, and wearable gadgets. This LiPo battery features a flat pouch design that allows easy integration into compact devices. The high energy density and stable discharge characteristics make it suitable for applications requiring long-lasting power in a small form factor. The battery can be charged using standard LiPo charging modules and provides dependable performance for hobby electronics and portable systems. 🔹 Key Features Nominal Voltage 3.7V Capacity 1000mAh Lightweight and compact pouch design Rechargeable Lithium Polymer battery High energy density Low self-discharge rate Stable discharge performance Suitable for portable electronics 🔹 Technical Specifications Parameter Specification Model 803040 Battery Type Lithium Polymer (LiPo) Nominal Voltage 3.7V Fully Charged Voltage 4.2V Capacity 1000mAh Charging Method CC-CV Discharge Cut-off Voltage 3.0V Cell Type Pouch Cell Rechargeable Yes 🔹 Applications DIY electronics projects IoT devices Bluetooth modules Portable gadgets GPS devices Wearable electronics Robotics projects Power banks 🔹 Package Includes 1 × 803040 3.7V 1000mAh Lithium Polymer Rechargeable Battery ⚠ Battery color and label may vary depending on batch. ⚠ Safety Instructions Do not short circuit the battery terminals. Do not charge above 4.2V. Do not discharge below 3.0V. Use a LiPo compatible charger. Do not puncture or expose to fire. Do not charge unattended. Store in a cool and dry place.
Out of stock146074 3.7V 10000mAh Rechargeable Lithium Polymer (Li-Po) Battery Cell for Power Bank & Electronic Devices
[LiPo Cell] The 146074 3.7V 10000mAh Lithium Polymer Rechargeable Battery Cell is a high-capacity flat Li-Po battery designed for portable electronic devices and power bank applications. With a large 10000mAh capacity, it provides long-lasting power while maintaining a compact and lightweight design. This lithium polymer cell is widely used in DIY power banks, Bluetooth speakers, tablets, GPS devices, IoT systems, portable electronics, and backup power systems. The battery includes protection circuitry compatibility and provides stable voltage output for reliable performance in demanding applications. 🔹 Key Features High capacity 10000mAh lithium polymer battery Nominal voltage 3.7V Lightweight and compact flat design Rechargeable Li-Po chemistry High energy density Stable discharge performance Suitable for portable electronics and DIY power banks 🔹 Technical Specifications Battery Type: Lithium Polymer (Li-Po) Model: 146074 Nominal Voltage: 3.7V Fully Charged Voltage: 4.2V Rated Capacity: 10000mAh Actual Capacity: 90-92% of Rated Capacity Cell Type: Flat pouch cell Charging Method: CC-CV (Constant Current / Constant Voltage) Charge Voltage: 4.2V Discharge Cut-off Voltage: 3.0V Rechargeable: Yes 🔹 Applications Power banks DIY battery packs Bluetooth speakers Portable electronics IoT devices GPS devices Tablets and handheld devices Backup power systems ⚠ Safety Instructions Do not short circuit battery terminals. Do not overcharge above 4.2V. Do not discharge below 3.0V. Use only compatible Li-Po charger or protection board. Do not puncture or expose battery to fire or heat. Do not charge unattended. Store in a cool and dry place. 🔹 Package Includes 1 × 146074 3.7V 10000mAh Lithium Polymer Battery Cell ⚠ Battery color and label may vary depending on stock batch.
113440P 3.7V 1500mAh Lithium Polymer Rechargeable Li-Po Pouch Cell
[LiPo Cell] The 113440P 3.7V 1500mAh Lithium Polymer Battery is a compact and lightweight rechargeable Li-Po pouch cell designed for reliable power delivery in modern electronic applications. With a nominal voltage of 3.7V and a high capacity of 1500mAh, this battery is well-suited for DIY electronics, IoT devices, Bluetooth speakers, GPS trackers, medical devices, wearables, and portable gadgets. Manufactured using advanced lithium polymer chemistry, the battery offers stable discharge performance, low internal resistance, and long cycle life. Its flat pouch form factor allows easy integration into slim and space-constrained designs where cylindrical cells are not suitable. For safe operation, the battery should be used with a proper Li-Po charging circuit (CC/CV) and protection module (PCM/BMS) to prevent over-charge, over-discharge, over-current, and short-circuit conditions. ⭐ KEY FEATURES ✔ Nominal Voltage: 3.7V✔ Capacity: 1500mAh✔ Lithium Polymer (Li-Po) Chemistry✔ Rechargeable & Long Cycle Life✔ Slim pouch / flat cell design✔ Stable discharge & low self-discharge✔ Lightweight and compact✔ Suitable for DIY & OEM applications 🔧 TECHNICAL SPECIFICATIONS Model: 113440P Battery Type: Lithium Polymer (Li-Po) Nominal Voltage: 3.7V Rated Capacity: 1500mAh Max Charging Voltage: 4.2V Discharge Cut-off Voltage: ~3.0V Rechargeable: Yes Form Factor: Pouch / Flat Cell 🎯 APPLICATIONS DIY electronics projects IoT & embedded systems Bluetooth speakers & audio devices Wearable & medical devices GPS trackers Power banks & portable gadgets 📦 PACKAGE INCLUDES 1 × 113440P 3.7V 1500mAh Lithium Polymer Battery Cell(Quantity as per selected pack)
802540P 3.7V 1000mAh Rechargeable Lithium Polymer Battery
[LiPo Cell] The 802540P 3.7V 1000mAh Lithium Polymer Battery Cell is a compact and lightweight rechargeable Li-Po battery designed to deliver reliable and stable power for a wide range of electronic devices. With a nominal voltage of 3.7V and a capacity of 1000mAh, this battery is suitable for DIY electronics, IoT projects, wearable devices, Bluetooth speakers, GPS trackers, power banks, and portable gadgets. Built using high-quality lithium polymer chemistry, the cell provides low internal resistance, stable discharge performance, and long cycle life. Its flat pouch-style design allows easy integration into slim and compact devices where cylindrical batteries cannot be used. The battery can be safely charged using a proper Li-Po charging module (such as TP4056) and should be used with appropriate protection circuitry to prevent overcharge, over-discharge, and short-circuit conditions. ⭐ KEY FEATURES ✔ Nominal Voltage: 3.7V✔ Capacity: 1000mAh✔ Lithium Polymer (Li-Po) Chemistry✔ Rechargeable & Long Cycle Life✔ Slim, lightweight pouch cell design✔ Stable discharge & low self-discharge✔ Ideal for compact & portable devices 🔧 TECHNICAL SPECIFICATIONS Model: 802540P Battery Type: Lithium Polymer (Li-Po) Nominal Voltage: 3.7V Rated Capacity: 1000mAh Charging Voltage: 4.2V (Max) Discharge Cut-off Voltage: ~3.0V Rechargeable: Yes Form Factor: Pouch / Flat Cell 🎯 APPLICATIONS DIY electronics projects IoT & embedded systems Bluetooth speakers & headsets Wearable devices GPS trackers Power banks Portable gadgets 📦 PACKAGE INCLUDES 1 × 802540P 3.7V 1000mAh Lithium Polymer Battery Cell
Nickel Strip 0.12mm × 5mm 1P Plane Coated Nickel Welding Strip for 18650 Lithium Battery Pack – 1 Meter
[Nickel Strip] The Nickel Strip 0.12mm × 5mm 1P Plane Coated Nickel Welding Strip is specially designed for assembling and repairing 18650 lithium battery packs and other rechargeable battery modules. Made from nickel-coated steel, this strip provides a strong mechanical bond, good electrical conductivity, and excellent weldability. Its flat 1P plane design ensures stable current flow and reliable cell connections. The nickel coating protects against rust and corrosion, making it suitable for long-term use in power banks, e-bike battery packs, solar storage systems, UPS batteries, and DIY lithium battery projects. Supplied in a convenient 1 meter length, this strip is easy to cut, bend, and shape according to your battery pack layout. 🔹 Key Features Made from nickel-coated steel for strength and durability Size: 0.12mm thickness × 5mm width Flat 1P plane strip design Good electrical conductivity and strong weld joints Excellent for spot welding lithium battery cells Corrosion-resistant nickel coating Easy to cut, bend, and form Suitable for 18650, 21700, 26650 lithium cells 🔹 Technical Specifications Material: Nickel-coated steel (Coated Nickel) Thickness: 0.12 mm Width: 5 mm Type: 1P Plane Flat Strip Length: 1 Meter Color: Silver Application: Spot welding for lithium battery packs Compatible Cells: 18650, 21700, 26650 and similar cylindrical cells Conductivity: Good Corrosion Resistance: High (nickel-coated surface) 🔹 Applications 18650 lithium battery pack assembly Power bank manufacturing and repair E-bike and electric vehicle battery packs Solar battery storage systems UPS and inverter battery packs DIY lithium battery projects Battery repair and maintenance 🔹 Package Contents 1 × Coated Nickel Welding Strip (0.12mm × 5mm, Length: 1 Meter)
Nickel Strip 0.12mm × 4mm 1P Plane Coated Nickel Welding Strip for 18650 Lithium Battery Pack – 1 Meter
[Nickel Strip] The Nickel Strip 0.12mm × 4mm 1P Plane Coated Nickel Welding Strip is specially designed for assembling and repairing 18650 lithium battery packs and other rechargeable battery modules. Made from nickel-coated steel, this strip provides a strong mechanical bond, good electrical conductivity, and excellent weldability. Its flat 1P plane design ensures stable current flow and reliable cell connections. The nickel coating protects against rust and corrosion, making it suitable for long-term use in power banks, e-bike battery packs, solar storage systems, UPS batteries, and DIY lithium battery projects. Supplied in a convenient 1 meter length, this strip is easy to cut, bend, and shape according to your battery pack layout. 🔹 Key Features Made from nickel-coated steel for strength and durability Size: 0.12mm thickness × 4mm width Flat 1P plane strip design Good electrical conductivity and strong weld joints Excellent for spot welding lithium battery cells Corrosion-resistant nickel coating Easy to cut, bend, and form Suitable for 18650, 21700, 26650 lithium cells 🔹 Technical Specifications Material: Nickel-coated steel (Coated Nickel) Thickness: 0.12 mm Width: 4 mm Type: 1P Plane Flat Strip Length: 1 Meter Color: Silver Application: Spot welding for lithium battery packs Compatible Cells: 18650, 21700, 26650 and similar cylindrical cells Conductivity: Good Corrosion Resistance: High (nickel-coated surface) 🔹 Applications 18650 lithium battery pack assembly Power bank manufacturing and repair E-bike and electric vehicle battery packs Solar battery storage systems UPS and inverter battery packs DIY lithium battery projects Battery repair and maintenance 🔹 Package Contents 1 × Coated Nickel Welding Strip (0.12mm × 4mm, Length: 1 Meter)
Nickel Strip 0.15mm × 6mm 1P Pure Nickel Welding Strip for 18650 Lithium Battery Pack – 1 Meter
[Nickel Strip] The Nickel Strip 0.15mm × 6mm 1P Pure Nickel Welding Strip is specially manufactured for building and repairing 18650 lithium battery packs and other rechargeable battery assemblies. Made from high-purity nickel, this strip offers low electrical resistance, excellent conductivity, and strong spot-welding performance. Its flat 1P plane design ensures uniform current flow and reliable connections between battery cells. The strip is corrosion-resistant and durable, making it ideal for long-term use in power banks, e-bike battery packs, solar storage systems, UPS batteries, and DIY lithium battery projects. Supplied in a convenient 1 meter length, this strip is easy to cut and shape according to your battery pack design. 🔹 Key Features Made from pure nickel (not nickel-plated steel) Size: 0.15mm thickness × 6mm width Flat 1P plane strip for uniform current flow Excellent conductivity with low internal resistance Strong and reliable for spot welding Corrosion-resistant and long-lasting Easy to cut, bend, and shape Perfect for 18650, 21700, 26650 lithium battery packs 🔹 Technical Specifications Material: Pure Nickel Thickness: 0.15 mm Width: 6 mm Type: 1P Plane Flat Strip Length: 1 Meter Color: Silver Application: Spot welding for lithium battery packs Compatible Cells: 18650, 21700, 26650 and similar cylindrical cells Resistance: Very low (high conductivity) Corrosion Resistance: Excellent 🔹 Applications 18650 lithium battery pack assembly Power bank manufacturing and repair E-bike and electric vehicle battery packs Solar battery storage systems UPS and inverter battery packs DIY lithium battery projects Battery repair and maintenance 🔹 Package Contents 1 × Pure Nickel Welding Strip (0.15mm × 6mm, Length: 1 Meter)