All products · 68 of 1440
Electronics, sensors, robotics kits, PC components, peripherals — everything Unik Systems carries, in one place.
8×8 LED Matrix Module (MAX7219)
MAX7219 dot LED matrix module, MCU controlled display.
7-Segment LED Display (4-digit)
LED 4-digit display module with clock point, 4-pin Dupont line for Arduino.
Only 2 leftGSM SIM800L
GPRS transfer board, micro SIM, GSM core, TTL port for Arduino.
Laser Diode Module (650nm 5mW)
650nm 6mm 5V DC 5mW mini laser dot diode module.
Sound Playback Module
Voice board, recording, recorder, playback, mic, sound, audio loudspeaker.
Out of stock0.96 Inch Blue SPI OLED Display Module 7-Pin 128×64 – SSD1306
[LED/LCD Display] 0.96 Inch Blue SPI OLED Display Module 7-Pin 128×64 – SSD1306 The 0.96-inch Blue OLED Display Module is a compact graphical display based on the SSD1306 driver IC, featuring a 128×64 pixel resolution and blue monochrome display. This version has a 7-pin interface with a dedicated CS (Chip Select) pin, making it suitable for 4-wire SPI communication. The module is factory-configured for SPI and can also be modified for I2C/IIC communication on compatible board versions. With its compact size, wide viewing angle and low-power OLED technology, it is suitable for Arduino, ESP32, ESP8266, STM32, Raspberry Pi and other microcontroller projects. ⭐ Key Features 0.96-inch blue OLED display 128 × 64 pixel resolution SSD1306 driver IC 7-pin interface Dedicated CS (Chip Select) pin Factory configured for 4-wire SPI Supports SPI and I2C/IIC with appropriate configuration 3.3V/5V compatible on supported module versions No backlight required Low power consumption Wide viewing angle of more than 160° Compact PCB design Pre-soldered 7-pin male header Compatible with Arduino, ESP32, ESP8266, STM32 and Raspberry Pi projects 📋 Technical Specifications Display Type: OLED (Organic Light-Emitting Diode) Display Colour: Blue Display Size: 0.96 inch Driver IC: SSD1306 Resolution: 128 × 64 pixels Interface: SPI / I2C Default Interface: 4-wire SPI Input Voltage: 3.3V–5V Viewing Angle: >160° Module Dimensions: Approximately 27 × 27 × 4mm Operating Temperature: Approximately -30°C to +70°C Header: 7-pin male header, pre-soldered Display Type: Monochrome blue OLED 🔌 7-Pin Interface The 7-pin version provides the following connections: GND – Ground VCC – Power supply D0 / SCK / CLK – SPI clock D1 / MOSI / SDA – SPI data RES / RST – Display reset DC / A0 – Data/Command selection CS – Chip Select 🛠️ SPI Connection The module is normally supplied in 4-wire SPI configuration. For an Arduino Uno, a typical connection is: VCC → 5V GND → GND D0 → SCK / D13 D1 → MOSI / D11 RES → Digital I/O DC → Digital I/O CS → Digital I/O The dedicated CS pin allows the OLED to share the SPI bus with other devices such as SD cards or additional SPI peripherals. 🔄 I2C / IIC Configuration On compatible versions, the module can be converted from SPI to I2C by changing the appropriate resistor configuration on the PCB. The supplied board configuration may require: Moving the resistor from R3 to R1 Shorting R8 with solder Using D0 as SCL Using D1 as SDA Configuring DC for the I2C address The exact resistor positions can vary between board revisions, so check the markings on your particular PCB before modification. 🎯 Applications Arduino projects ESP32 projects ESP8266 projects STM32 development Raspberry Pi projects IoT devices Sensor displays Voltage/current meters Battery monitors Temperature displays Digital clocks Data loggers Portable electronic devices Robotics DIY measuring instruments Embedded systems Menu and status displays 💡 Advantages of OLED OLED technology is self-emissive, meaning the pixels produce their own light and do not require a conventional backlight. This provides high contrast, compact construction and a wide viewing angle while keeping power consumption relatively low. ⚠️ Important Notes This is the 7-pin SPI version, not the 6-pin version. The module is normally configured for SPI communication. Check the PCB labels before connecting the module. Do not exceed the specified supply voltage. Although many versions support 5V operation, the exact voltage tolerance can vary between board revisions. I2C operation may require hardware resistor modification. The actual PCB layout and component markings may vary slightly between production batches. Display colour: Blue. Libraries such as Adafruit SSD1306 and U8g2 can be used with compatible microcontrollers. 📦 Package Includes 1 × 0.96 Inch Blue SPI OLED Display Module
48mm Square Internal Magnet Speaker – 4Ohms 5W
[Speakers] 48mm Square Internal Magnet Speaker – 4Ω 5W The 48mm Square Internal Magnet Speaker is a compact full-range audio driver designed for clear and efficient sound reproduction in space-constrained applications. With a 4Ω impedance and 5W power rating, this speaker is suitable for Bluetooth speakers, portable audio systems, DIY speaker projects and embedded electronic devices. Its square frame allows convenient mounting inside compact enclosures and panels. ⭐ Key Features Compact square speaker design 4Ω impedance 5W power rating Internal magnet construction Full-range audio output Compact size for space-limited applications Easy to install inside speaker enclosures Suitable for DIY and commercial audio projects Lightweight and practical design 📋 Technical Specifications Speaker Type: Internal Magnet Speaker Shape: Square Speaker Size: 48mm class Model: 4Ω 5W Impedance: 4Ω Power Rating: 5W Magnet Type: Internal Magnet Audio Type: Full-range Mounting Type: Panel / Enclosure Mount Dimensions: 47 × 29 × 23mm Application: Compact audio systems, DIY electronics and portable speakers 🔧 Applications Bluetooth speaker systems Portable speakers DIY speaker projects Compact audio enclosures Embedded audio systems Intercom systems Alert and notification devices Educational electronics projects Consumer electronic devices Custom audio projects 🛠️ Installation Connect the speaker to a compatible amplifier with a 4Ω output. Ensure the amplifier's output power is suitable for the speaker's 5W rating. Mount the speaker securely inside the enclosure to reduce unwanted vibration. Observe correct speaker polarity when connecting multiple speakers. 📦 Package Includes 1 × 48mm Square Internal Magnet Speaker Impedance: 4Ω Power: 5W ⚠️ Precautions Do not exceed the 5W rated power for prolonged operation. Use a compatible 4Ω amplifier. Avoid short-circuiting the speaker terminals. Keep away from moisture, excessive heat and physical damage. Ensure proper mounting to minimize vibration and unwanted noise. Actual sound quality depends on the amplifier, enclosure and application.
Out of stockGold AP-55 TPA3116D2 2×50W Bluetooth Stereo Digital Amplifier Board with USB, TF Card, FM & Remote
[Amplifier Board] Gold AP-55 TPA3116D2 2×50W Bluetooth Stereo Digital Amplifier Board with USB, TF Card, FM & Remote The Gold AP-55 is a compact Class-D stereo digital audio amplifier board based on the TPA3116D2 amplifier IC, designed for DIY Bluetooth speakers, home audio systems, portable speakers, bookshelf speakers, multimedia systems, and custom audio projects. Available product listings consistently identify the AP-55 as a dual-channel 50W + 50W amplifier, with a DC input range around 8–24V or 12–24V depending on the listing/version. The AP-55 combines the power amplifier with a multimedia player supporting Bluetooth 5.0, USB, TF/SD card, FM radio and AUX input. The Bluetooth device name is reported as GD-82EM, while the FM tuner covers 87.5–108.0MHz. It also includes an infrared remote control and a digital display for convenient operation. The TPA3116D2 Class-D amplifier provides efficient stereo amplification, making the board suitable for building compact but powerful audio systems. One detailed listing specifies support for 4Ω–8Ω speakers, with the commonly advertised maximum output of 50W per channel. ⭐ Key Features Gold AP-55 amplifier module TPA3116D2 Class-D amplifier IC 50W + 50W dual-channel stereo output Supports 4Ω–8Ω speakers Bluetooth 5.0 wireless audio Bluetooth device name: GD-82EM Built-in USB music player Built-in TF / SD card player Built-in FM radio FM frequency range 87.5–108.0MHz 3.5mm AUX input Infrared remote control Digital display Supports MP3 / WMA / WAV Power-off memory function Remembers the previous song and volume Compact design for DIY speaker projects High-efficiency Class-D amplification 📋 Technical Specifications Product Type: Stereo Class-D Digital Amplifier Board Model: Gold AP-55 Amplifier IC: TPA3116D2 Amplifier Class: Class-D Number of Channels: 2 / Stereo Output Power: 50W + 50W Maximum Total Output: 100W Speaker Impedance: 4Ω–8Ω Input Voltage: DC 8–24V (some listings specify 12–24V; verify the exact board version before use) Bluetooth Version: 5.0 Bluetooth Name: GD-82EM Bluetooth Range: Up to approximately 10–15m under suitable conditions Audio Formats: MP3 / WMA / WAV USB Support: Yes TF/SD Card Support: Yes FM Radio: Yes FM Frequency: 87.5–108.0MHz AUX Input: 3.5mm / Wired Audio Input Remote Control: IR Remote Remote Range: Approximately 4–7m Display: Digital Display Power-Off Memory: Yes Memory Function: Last song and volume Audio Input Modes: Bluetooth / USB / TF Card / FM / AUX Output: Dual-Channel Stereo Efficiency: Greater than 90% according to one detailed listing SNR: Approximately 102dB according to one detailed listing Distortion: Below 0.1% at normal listening levels according to one detailed listing Board Size: Approximately 70 × 50 × 20mm with shell, according to one listing 🎵 Audio & Playback Functions The AP-55 can switch between Bluetooth, USB, TF/SD Card, FM Radio and AUX sources. When Bluetooth mode is selected, users can pair a phone or other compatible device with GD-82EM. USB and TF/SD cards can be used for local music playback, while AUX provides a wired audio input. 📻 FM Radio The built-in FM tuner supports the 87.5–108.0MHz broadcast band. FM stations can be searched and selected using the onboard controls or remote control. 🎛️ Controls & Remote The module provides controls for functions such as previous track, next track, volume up, volume down, play/pause, mode selection and FM station selection. The infrared remote provides additional wireless control of playback, volume, mode and other supported functions. 🔧 Applications DIY Bluetooth Speakers High-Power Bluetooth Speaker Projects Portable Speaker Systems Bookshelf Speaker Systems Home Audio Projects Multimedia Speaker Systems USB MP3 Speaker Systems TF/SD Card Music Players FM Radio Speaker Projects Car Audio Projects Custom Wooden Speaker Cabinets Desktop Audio Systems Electronics DIY Projects 🛠️ Installation Connect a suitable DC power supply within the specified voltage range and observe the correct polarity. Connect the left and right speaker outputs to compatible 4Ω–8Ω speakers. Select Bluetooth, USB, TF/SD, FM or AUX according to the desired audio source. For maximum advertised output, a suitable 24V high-current power supply is recommended by one vendor; at lower supply voltages, available output power will be lower. 📦 Package Includes 1 × Gold AP-55 TPA3116D2 2×50W Bluetooth Amplifier Board 1 × IR Remote Control 1 × Required Connecting Wires/Cables (package contents may vary by seller/version) ⚠️ Precautions Verify the exact input voltage requirement of your AP-55 version before powering it. Do not exceed 24V DC where the board specification limits input to 24V. Check power polarity carefully before connection. Use speakers with a compatible 4Ω–8Ω impedance. Do not short-circuit the speaker output terminals. Ensure adequate ventilation during high-power operation. Use a suitable high-current power supply for high-output operation. Do not connect the speaker outputs together or directly to ground. Keep the board away from moisture and conductive materials. Incorrect wiring or excessive voltage can permanently damage the amplifier IC.
45mm 1.75-Inch 4Ohms 3W Internal Magnet Speaker with Frame
[Speakers] 45mm Internal Magnet Speaker with Frame – 4Ω 3W 45×23×23mm The 45mm Internal Magnet Speaker with Frame (1.75-Inch) is a compact and efficient audio driver designed for DIY electronics, portable audio devices, multimedia systems, toys, alarms, intercoms, and embedded audio applications. Featuring an internal magnet structure and durable mounting frame, this speaker provides clear and stable sound output while maintaining a compact form factor. With a compact size of 45×23×23mm, 4Ω impedance, and 3W power rating, this speaker is suitable for small amplifier projects and electronic devices where space is limited. Its built-in frame allows convenient installation in custom enclosures, panels, and electronic products. ⭐ Key Features 45mm (1.75-Inch) speaker size 4Ω impedance 3W power rating Internal magnet design Durable mounting frame Compact 45×23×23mm construction Clear and stable sound output Lightweight and space-saving Suitable for low-power audio applications Easy to install in custom enclosures Ideal for DIY, repair and OEM applications 📋 Technical Specifications Product Type: Internal Magnet Speaker Speaker Size: 45mm (1.75 Inch) Dimensions: 45 × 23 × 23mm Impedance: 4Ω Power Rating: 3W Magnet Type: Internal Magnet Frame Type: With Mounting Frame Speaker Type: Dynamic Full Range Speaker Audio Type: Mini Full Range Speaker Mounting: Frame / Panel Mount Application: Compact Audio & Embedded Electronics 🔧 Applications DIY Speaker Projects Portable Audio Devices Bluetooth Speaker Projects Multimedia Speaker Systems Alarm Systems Toys and Sound Modules Intercom Systems Embedded Electronics Educational Electronics Kits Replacement Speaker Repairs Smart Gadgets OEM Product Manufacturing Mini Amplifier Projects 🛠️ Installation Mount the speaker securely inside the required enclosure or panel using its mounting frame. Connect it to a compatible amplifier with an output suitable for 4Ω speakers and a power rating appropriate for the 3W speaker. Proper mounting helps reduce unwanted vibration and improves overall sound performance. 📦 Package Includes 1 × 45mm Internal Magnet Speaker with Frame – 4Ω 3W ⚠️ Precautions Match the 4Ω impedance with the amplifier output. Do not exceed the 3W rated power. Do not apply direct DC voltage to the speaker. Ensure correct wiring polarity during installation. Avoid exposure to moisture and excessive dust. Mount securely to prevent vibration and unwanted noise. Do not apply physical pressure to the speaker cone or diaphragm. Use a compatible audio amplifier module for proper operation.
2 Inch 4 Ohms 5Watt Internal Magnet Speaker with Frame
[Speakers] 2-Inch Internal Magnet Speaker with Frame – 53×29×23mm 4Ω 5W The 2-Inch Internal Magnet Speaker with Frame is a compact and efficient audio driver designed for DIY electronics, portable audio devices, alarms, toys, embedded systems, and other space-constrained applications. Featuring an internal magnet design and durable frame construction, this speaker provides clear and balanced sound output while maintaining a compact footprint. With dimensions of 53×29×23mm, 4Ω impedance, and a 5W power rating, this speaker is suitable for small amplifier projects and electronic devices requiring a compact audio solution. The mounting frame makes installation convenient in custom enclosures and equipment. ⭐ Key Features 2-Inch compact speaker design Internal magnet structure 4Ω impedance 5W power rating Durable metal frame construction Clear and balanced sound output Compact and space-saving design Easy mounting with frame and screw slots Suitable for low and medium-power audio applications Ideal for DIY and OEM applications 📋 Technical Specifications Product Type: Dynamic Internal Magnet Speaker Speaker Size: 2 Inch Dimensions: 53 × 29 × 23mm Impedance: 4Ω Power Rating: 5W Magnet Type: Internal Magnet Magnet Material: Ferrite Shape: Rectangular Frame Type: Metal Frame Cone Material: Paper / Mylar Diaphragm depending on variant Speaker Type: Full Range / Dynamic Speaker Mounting: Frame with Screw Slots Application: Compact Audio & Embedded Electronics 🔧 Applications DIY Speaker Projects Portable Audio Devices Bluetooth Speaker Projects Alarm Systems Toys and Sound Modules Intercom Systems Embedded Electronics Educational Electronics Kits Replacement Speaker Repairs Smart Gadgets OEM Product Manufacturing Mini Amplifier Projects 🛠️ Installation Connect the speaker to a compatible amplifier output matching the speaker's 4Ω impedance and 5W power rating. Secure the speaker firmly using the mounting frame to reduce unwanted vibration and noise during operation. 📦 Package Includes 1 × 2-Inch Internal Magnet Speaker with Frame – 4Ω 5W ⚠️ Precautions Match the 4Ω impedance with the amplifier output. Do not exceed the 5W rated power. Avoid applying direct DC voltage to the speaker. Avoid exposure to moisture and excessive humidity. Mount the speaker securely before operation. Do not apply physical pressure to the speaker cone or diaphragm. Avoid short circuits at the speaker terminals. Keep the speaker away from excessive heat and magnetic interference.
2.25-Inch 8ohms 8W Full Range Speaker for Compact Audio Applications
[Speakers] 2.25-Inch 8Ω 8W Full Range Speaker for Compact Audio Applications The 2.25-Inch 8Ω 8W Full Range Speaker is a compact and efficient audio driver designed for small electronic and embedded sound applications. Featuring an 8Ω impedance and 8W power rating, this speaker delivers clear and balanced sound output while maintaining low power consumption and excellent efficiency. Its compact size makes it ideal for projects where installation space is limited, including portable speakers, DIY electronics, toys, alarm systems, intercom devices, and mini speaker enclosures. The full-range design allows it to reproduce a broad range of audio frequencies, making it suitable for both voice and music playback applications. Built with durable materials and designed for reliable long-term performance, this speaker is an excellent choice for electronics hobbyists, engineers, and product developers working on custom audio projects. ⭐ Key Features 2.25-Inch compact speaker driver 8Ω impedance 8W power rating Full-range audio reproduction Clear and balanced sound output Lightweight and compact design Easy to mount in enclosures and panels Suitable for low to medium-power audio applications Durable construction for long-term use Ideal for DIY and embedded audio systems 📋 Technical Specifications Product Type: Full Range Speaker Speaker Size: 2.25 Inch Impedance: 8Ω Power Rating: 8W Speaker Type: Full Range Mounting Type: Enclosure / Panel Mount Application Type: Audio Output 🔧 Applications Portable Speaker Systems DIY Audio Projects Bluetooth Speaker Modules Toys and Educational Kits Alarm and Notification Systems Embedded Electronic Devices Mini Amplifiers and Sound Modules Intercom Systems Robotics Projects Custom Speaker Enclosures ⚠️ Precautions Do not exceed the 8W rated power. Use an amplifier compatible with an 8Ω speaker load. Avoid exposure to moisture and excessive dust. Mount securely to minimize vibration and distortion. Do not apply direct pressure on the speaker cone. 📦 Package Includes 1 × 2.25-Inch 8Ω 8W Full Range Speaker
57mm (2.25-Inch) Internal Magnet Speaker 4Ohms 3W Full Range Audio Speaker
[Speakers] 57mm (2.25-Inch) Internal Magnet Speaker – 4Ω 3W Full Range Audio Speaker The 57mm (2.25-Inch) Internal Magnet Speaker is a compact and reliable full-range audio speaker designed for DIY electronics, multimedia devices, embedded sound systems, and portable audio applications. Featuring a 4Ω impedance and 3W power rating, this speaker delivers clear and balanced sound output while maintaining a slim and lightweight design. Its internal magnet structure provides a compact profile, making it ideal for applications where installation space is limited. The durable mounting frame allows easy integration into speaker enclosures, control panels, intercom systems, audio modules, and custom electronic projects. Designed for consistent audio performance, this speaker is suitable for voice playback, music, alerts, and general audio output in both portable and embedded electronic devices. ⭐ Key Features 57mm (2.25-Inch) compact speaker 4Ω impedance 3W power rating Internal magnet design Full-range audio reproduction Built-in mounting frame Clear and balanced sound output Compact and lightweight construction Easy installation in custom enclosures Suitable for portable and embedded audio applications Ideal for DIY electronics and speaker projects 📋 Technical Specifications Product Type: Internal Magnet Speaker Speaker Size: 57mm (2.25 Inch) Impedance: 4Ω Power Rating: 3W Speaker Type: Full Range Magnet Type: Internal Magnet Frame Type: With Mounting Frame Mounting: Frame / Panel Mount Application: Embedded Audio Systems 🔧 Applications DIY Electronics Projects Audio Modules & Music Players Intercom and Communication Systems Toys and Educational Devices Portable Audio Systems Alarm and Notification Devices Embedded Audio Applications Mini Speaker Enclosures Multimedia Devices Robotics and Automation Projects ⚠️ Precautions Do not exceed the 3W rated power. Use an amplifier compatible with a 4Ω speaker load. Ensure proper wiring polarity during installation. Avoid exposure to moisture and dust. Mount securely to reduce vibration noise. Do not apply direct pressure on the speaker cone. 📦 Package Includes 1 × 57mm (2.25-Inch) 4Ω 3W Internal Magnet Full Range Speaker
45mm (1.75-Inch) Internal Magnet Speaker 2 Ohms 10W Full Range Audio Speaker
[Speakers] 45mm (1.75-Inch) Internal Magnet Speaker – 2Ω 10W Full Range Audio Speaker The 45mm (1.75-Inch) Internal Magnet Speaker is a compact and powerful audio driver designed for DIY electronics, portable speakers, multimedia devices, toys, embedded audio systems, and custom speaker enclosures. Featuring a 2Ω impedance and 10W power rating, this speaker provides strong audio output when paired with a compatible amplifier. Its internal magnet design provides a compact profile while maintaining efficient magnetic performance. The built-in mounting frame makes installation easy in custom enclosures and electronic devices. With its 2Ω low-impedance configuration, this speaker is suitable for compatible Class-D amplifier modules where higher output power is required from a compact speaker driver. ⭐ Key Features 45mm (1.75-Inch) compact speaker 2Ω impedance 10W power rating Internal magnet design Full-range audio reproduction Compact and lightweight construction Built-in mounting frame Clear and powerful sound output Easy to install in custom enclosures Suitable for portable and embedded audio applications Ideal for DIY speaker projects 📋 Technical Specifications Product Type: Internal Magnet Speaker Speaker Size: 45mm (1.75 Inch) Impedance: 2Ω Power Rating: 10W Speaker Type: Full Range Magnet Type: Internal Magnet Frame Type: Mounting Frame Mounting: Frame / Panel Mount Application: Embedded & Portable Audio 🔧 Applications DIY Bluetooth Speaker Projects Portable Speaker Systems Mini Audio Amplifiers Multimedia Devices Toys and Educational Kits Intercom Systems Alarm and Notification Systems Embedded Audio Devices Custom Speaker Enclosures Robotics Projects Electronic Projects ⚠️ Precautions Use an amplifier that supports a 2Ω load. Do not exceed the 10W rated power. Check amplifier output impedance before connecting. Observe correct speaker polarity during installation. Avoid excessive mechanical pressure on the speaker cone. Keep away from moisture and excessive dust. Mount securely to minimize unwanted vibration and distortion. 📦 Package Includes 1 × 45mm (1.75-Inch) 2Ω 10W Internal Magnet Full Range Speaker
2.25 Inch 4 Ohm 10 Watt Full Range Speaker with Neodymium Magnet
[Speakers] 2.25-Inch Speaker Driver • 4 Ohm Impedance • 10W Power Rating • Neodymium Magnet • Compact Full Range Audio Speaker The 2.25 Inch 4 Ohm 10 Watt Full Range Speaker with Neodymium Magnet is a compact and high-performance speaker driver designed for portable audio systems, DIY speaker projects, multimedia devices, embedded electronics, and custom sound enclosures. Featuring a powerful neodymium magnet, this speaker delivers clear vocals, balanced midrange, and improved bass response while maintaining a lightweight and compact design. With a 4 ohm impedance and 10 watt power rating, the speaker is suitable for use with small audio amplifiers, Bluetooth amplifier modules, DIY portable speakers, mini sound systems, toys, alarm systems, educational kits, and embedded electronic devices. The full-range design allows it to reproduce a wide spectrum of audio frequencies without requiring additional tweeters for many compact applications. Its durable construction and lightweight neodymium magnet assembly make it ideal for applications where both performance and space efficiency are important. ⭐ Features Compact 2.25-inch full range speaker Powerful neodymium magnet 4 ohm impedance 10 watt power rating Clear and balanced sound output Enhanced vocal clarity and midrange performance Lightweight and compact construction Easy to mount in custom enclosures Suitable for portable and embedded audio systems Ideal for DIY electronics and audio projects 📋 Technical Specifications Product Type: Full Range Speaker Driver Speaker Size: 2.25 Inch Impedance: 4 Ohm Power Rating: 10 Watt Magnet Type: Neodymium Speaker Type: Full Range Mounting Type: Enclosure / Panel Mount Application Type: Audio Output Frame Material: Metal Cone Material: Paper Composite Color: Black 🔧 Applications Suitable for: Portable Speaker Systems Bluetooth Speakers DIY Audio Projects Mini Sound Systems Multimedia Devices Toys and Educational Kits Alarm and Notification Systems Embedded Electronic Devices Mini Amplifiers Sound Modules Intercom Systems Custom Speaker Enclosures Robotics and Electronics Projects 📦 Package Includes 1 × 2.25 Inch 4 Ohm 10 Watt Full Range Speaker with Neodymium Magnet ⚠️ Precautions Do not exceed the 10W rated power. Use an amplifier compatible with 4 ohm speakers. Avoid exposure to moisture, water, and excessive dust. Mount the speaker securely to minimize unwanted vibration. Do not apply direct pressure to the speaker cone or surround.
Passive Radiator Bass Diaphragm Rubber Speaker Vibration Plate for DIY Speakers
[Passive Radiator] 🔊 Oval, Square & Round Passive Radiator Bass Diaphragm Rubber Speaker Vibration Plate for DIY Speakers Deep Bass Enhancement • Passive Design • No External Power Required • Ideal for DIY Speaker Projects The Rubber Passive Radiator Bass Diaphragm is a high-quality auxiliary bass vibration plate designed to significantly improve the low-frequency response of speaker systems. Available in Oval, Square, and Round shapes with multiple sizes, this passive radiator enhances bass performance without requiring additional power or amplifier channels. Unlike conventional speakers, a passive radiator does not contain a voice coil or magnet. Instead, it utilizes the air pressure generated by the active speaker driver to vibrate, producing deeper, richer bass while minimizing distortion and unwanted cabinet resonance. Manufactured using premium rubber and durable ABS materials, these passive radiators provide excellent flexibility, durability, and long service life. They are ideal for upgrading Bluetooth speakers, portable speakers, multimedia speakers, subwoofers, soundbars, and custom DIY audio projects. Whether you're repairing an existing speaker or building a custom enclosure, these passive bass diaphragms help deliver powerful low-frequency performance while maintaining compact enclosure sizes. ⭐ Features Premium quality rubber passive radiator Available in Oval, Square & Round shapes Produces deep and powerful bass response No power supply or wiring required Improves low-frequency performance Reduces speaker distortion Durable rubber suspension Lightweight and compact design Easy to install Ideal for DIY speaker upgrades and repairs 📋 Technical Specifications Product Type: Passive Radiator Bass Diaphragm Material: Rubber + ABS Plastic+Metal Shape: Oval / Square / Round (Depending on Selected Variant) Available Sizes: Multiple Sizes (2040 to 6090 Series) Operation: Passive (No Voice Coil or Magnet) Power Requirement: None Installation Type: Speaker Cabinet Mount Application: Low Frequency Bass Enhancement Color: Black 🔧 Applications Suitable for: Bluetooth Speakers Portable Speakers DIY Speaker Projects Multimedia Speakers Home Audio Systems Bookshelf Speakers Soundbars Subwoofers Wireless Speakers Audio System Repairs Custom Speaker Cabinets DIY Audio Enclosures 📦 Package Includes 1 × Passive Radiator Bass Diaphragm (Size & Shape as Selected) ⚠️ Note This is a passive radiator only and does not contain a voice coil, magnet, or electrical terminals. Product images are for reference only. The actual product may vary slightly in appearance depending on the selected size, shape, or manufacturing batch.
Out of stock1.3 Inch I2C IIC 128×64 OLED Display Module – White
[LED/LCD Display Module] The 1.3 Inch I2C 128×64 OLED Display Module is a compact, high-contrast display designed for Arduino, ESP32, NodeMCU, Raspberry Pi, and other microcontroller-based projects. This module uses OLED (Organic Light Emitting Diode) technology, providing bright white pixels with excellent contrast and wide viewing angles. Powered by the SSH1106 controller chip, the display offers smooth graphics rendering and reliable performance. With a resolution of 128×64 pixels, it can display text, graphics, icons, and sensor data clearly even in small embedded systems. The module communicates using the I2C (IIC) interface, requiring only 4 pins (VCC, GND, SDA, SCL), which helps save valuable GPIO pins on your microcontroller. It operates within a voltage range of 3.3V to 5V, making it compatible with most development boards. Unlike traditional LCD displays, OLED displays do not require a backlight because each pixel emits its own light. This results in lower power consumption, better contrast, and faster response times. Due to its compact size, lightweight design, and simple wiring, the display module is ideal for IoT devices, sensor monitors, battery indicators, portable electronics, robotics projects, and DIY electronics applications. ⭐ Features 1.3 Inch OLED Display Module 128 × 64 pixel resolution White pixel display SSH1106 display controller I2C / IIC communication interface Requires only 4 pins High contrast and wide viewing angle Low power consumption Compatible with Arduino, ESP32, NodeMCU, Raspberry Pi Ideal for embedded and IoT projects 🔧 Technical Specifications Display Size: 1.3 inch Resolution: 128 × 64 pixels Controller Chip: SSH1106 Display Area: 34.5 × 19 mm Interface Type: IIC / I2C Pixel Color: White Driving Voltage: 3.3V – 5V Operating Temperature: -40°C to 70°C Physical Dimensions Length: 35.5 mm Width: 33.5 mm Height: 4 mm Weight: 7 g 📦 Package Includes 1 × 1.3 Inch 128×64 OLED Display Module (White)
Portable USB Bluetooth Audio Music Receiver Dongle Adapter – Wireless Audio Receiver
[Audio Receiver] The Portable USB Bluetooth Audio Music Receiver Dongle Adapter instantly converts any car stereo, home speaker, PC speakers, or audio system into a wireless Bluetooth-enabled music receiver. Simply plug the dongle into a USB power source, connect its audio output to AUX, and enjoy seamless wireless music streaming from your smartphone, tablet, or laptop. This compact Bluetooth receiver delivers crisp, high-quality audio with stable transmission—making it perfect for cars without built-in Bluetooth, wired speakers, home audio systems, and portable sound setups. It supports all Bluetooth-enabled devices and offers quick pairing, low power consumption, and wide compatibility. Whether you're upgrading your car audio or converting old speakers into wireless ones, this USB Bluetooth receiver provides an easy and affordable solution. ✅ Features Convert any speaker or car stereo into a Bluetooth audio receiver Provides high-quality wireless music streaming from mobile, tablet, or laptop USB-powered – plug into car charger, power bank, or USB port Stable Bluetooth connection with fast pairing Compatible with car stereos, home speakers, multimedia systems, and amplifiers Ultra-compact, lightweight, and easy to carry Supports all major Bluetooth audio devices No drivers required – plug & play operation **** 3.5mm jack or cable not included***** 📘 Specifications Device Type: USB Bluetooth Audio Receiver Bluetooth Version: Standard high-quality audio support Input Power: USB 5V Output: 3.5mm AUX audio Transmission Distance: Approx. 8–10 meters Compatibility: Android, iOS, laptops, tablets, car stereos, speakers, amplifiers Usage: Car audio upgrade, home audio wireless streaming, mobile speaker enhancement Design: Compact & portable
ZK-MT21 bluetooth 5.0 Subwoofer Amplifier Board 50WX2+100W 2.1 Channel Power Audio Stereo Amplifier Tone Board Bass AMP AUX
[Amplifier Board] ZK-MT21 2.1 Channel Bluetooth 5.0 Audio Amplifier Module – 50W × 2 + 100W Subwoofer The ZK-MT21 2.1 Channel Bluetooth Audio Amplifier Module is a compact high-power stereo amplifier board designed for DIY Bluetooth speaker and home audio projects. It supports Bluetooth 5.0 and AUX audio input and provides dedicated left, right and subwoofer channels with adjustable volume, bass, treble, subwoofer volume and subwoofer frequency controls. With a suitable DC power supply and properly matched speakers, the module can deliver up to 50W + 50W for the left/right channels and up to 100W for the subwoofer channel. The board includes protection against reverse connection, overheating, overcurrent and short circuit. ⭐ Key Features Model: ZK-MT21 2.1 channel stereo audio amplifier Bluetooth 5.0 wireless audio input Bluetooth transmission distance up to approximately 15 meters under suitable conditions AUX wired audio input Left + Right + Subwoofer output Output up to 50W × 2 + 100W subwoofer Supports 4Ω–8Ω speakers Adjustable main volume Adjustable bass and treble for left/right channels Adjustable subwoofer volume Adjustable subwoofer frequency Subwoofer frequency adjustment range 20Hz–200Hz Reverse-polarity protection Overheat protection Overcurrent protection Short-circuit protection Compact amplifier board design Suitable for DIY Bluetooth speaker projects 📋 Technical Specifications Product Name: 2.1 Channel Audio Amplifier Module Model: ZK-MT21 Bluetooth Version: 5.0 Bluetooth Range: Approximately 15m Bluetooth Shielding: No shielding Audio Input: AUX + Bluetooth Channel: 2.1 Input Sensitivity: 500mV Amplifier Chip Solution: Domestic power amplifier chip Power Supply: DC 12–24V Recommended Supply Current: 5A or above Left Channel Output: <50W Right Channel Output: <50W Subwoofer Output: <100W Total Configuration: 50W × 2 + 100W Compatible Speaker Impedance: 4–8Ω Recommended Speaker Power: 20–100W Subwoofer Frequency Adjustment: 20Hz–200Hz Product Dimensions: 93 × 90 × 22mm Package Weight: Approximately 185g Protection: Reverse connection, overheat, overcurrent and short circuit ⚠️ Power Supply Warning:Do not connect this module directly to a 24V battery pack. Use a suitable regulated DC power supply as specified for the module. 🎛️ Control Functions MAIN-VOLUME: Controls the overall volume of the left, right and subwoofer channels. R&L CHANNEL-BASS: Adjusts bass level for the left and right channels. R&L CHANNEL-TREBLE: Adjusts treble level for the left and right channels. SUBWOOFER-VOLUME: Controls the subwoofer volume. SUBWOOFER-FREQ: Adjusts the subwoofer cutoff frequency from approximately 20Hz to 200Hz. 🔊 Speaker Selection Left and right channels can be connected to 4Ω–8Ω full-range or mid/high-frequency speakers. Recommended speaker power is 20W–100W. The subwoofer output should be connected to a suitable subwoofer speaker, not a regular full-range speaker. The subwoofer should have suitable low-frequency performance, with the source information recommending a frequency capability of at least 50Hz. Speaker impedance and power should be matched correctly with the amplifier. 🔌 Power Supply Selection The power supply is important for achieving proper amplifier performance and sound quality. A power supply with excessive ripple may increase background noise. Recommended supply: 18V / 19V / 24V with current above 5A Lower-voltage or lower-current supplies can be used, but available output power will be reduced. Insufficient supply current can cause voltage drop, abnormal operation or poor sound quality. If the amplifier is operated near maximum volume, an inadequate power supply may result in distortion. The power supply should have sufficient capacity for the actual amplifier load. Higher supply voltage can provide greater available output power within the module's specified operating range. 📱 Bluetooth & AUX Input The ZK-MT21 provides two audio input methods: Bluetooth Bluetooth 5.0 wireless audio input Bluetooth is the preferred input mode according to the supplied product information. Bluetooth supports automatic reconnection. Once Bluetooth is successfully connected, the module operates in Bluetooth mode. AUX Connect an external audio source through the AUX input. When using AUX, ensure the Bluetooth connection has been disconnected if necessary. 🔧 Applications DIY Bluetooth speakers 2.1 channel speaker systems Home audio projects Portable audio systems Subwoofer amplifier projects Custom speaker cabinets Desktop speaker systems Multimedia speaker systems Electronics and audio DIY projects Replacement/custom amplifier systems 🛠️ Installation & Usage Connect a suitable DC 12–24V power supply to the amplifier module. Connect the left and right speakers to their respective output terminals. Connect a suitable subwoofer to the subwoofer output. Ensure the speaker impedance is within the supported 4–8Ω range. Connect the audio source through Bluetooth or AUX. Adjust the main volume, bass, treble, subwoofer volume and frequency according to your requirements. Start with a low volume and gradually increase it. Ensure adequate ventilation and heat dissipation during high-power operation. ⚠️ Important Precautions Do not connect directly to a 24V battery pack. Use a suitable regulated DC power supply. Do not reverse the power supply polarity. Do not short-circuit the speaker outputs. Do not exceed the recommended speaker power and impedance. Ensure the power supply can provide sufficient current. Insufficient power may cause distortion or abnormal operation. Excessive load can cause the amplifier to heat up and activate thermal protection. Provide adequate ventilation during high-power operation. If distortion occurs at high volume, reduce the volume or use a more suitable power supply. The amplifier's actual output depends on the power supply, speaker impedance, audio input and overall system configuration. 📦 Package Includes 1 × ZK-MT21 Bluetooth 5.0 2.1 Channel Audio Amplifier Module
TPA3116D2 XH-M543 120W Dual Channel High Power Original Digital Power Amplifier Board
[Amplifier Board] Build your own music system with 120 watts of stereo output. TPA3116D2 XH-M548 Dual Channel 120W Digital Power Amplifier Board is newly designed digital audio amplifier board with fine quality is practical to install and use also has good performance. It features high-efficiency class D audio power amplifier with the latest and original TPA3116D2 core technology the BTL bridge circuit is more efficient than before. This product uses the double power supply transformer with a dynamic power supply range from 12V to 24V with high efficiency small quiescent current. Additionally, it is equipped with Perfect protection functions like overvoltage protection and output current limit. Features: A strong TPA3116D2 chip is a digital power amplifier chip, with low idle loss characteristics, makes it work well and quickly. Onboard, front-facing IC to improve the input sensitivity, high-definition sound quality. It can be used for car vehicle computer speaker, family audio and video, and empty square. This product has the characteristics of loud sound, the capacitance is large, excellent sound quality. There is no solder joint on the back of the circuit board, the chip capacitors, and the solder board together, so there is no possibility of short circuit. Package Includes: 1 x TPA3116D2 XH-M543 120W Dual Channel High Power Digital Power Amplifier Board
Passive Diaphragm Radiator Speaker Accessories Showcase Speaker Repair Parts
[Passive Radiator] Product Description: Model: 88 48 Low Frequency Vibration Plate Type: Sound film, diaphragm Material: Rubber Size: 88*48mm Net weight: 35 grams The bass radiator is also called a passive speaker. It is used to replace the inverted tube. The subwoofer made with the radiator has the following advantages compared with the traditional inverted subwoofer. The low frequency diving depth is equal to the back type, but the speed is the same. In this sense, it is faster than the inverted type, using the advantage of a certain closed box, and at the same time completely eliminating the disadvantage of the inverted structure-that is, the wind noise brought by the inverted nozzle. Package Includes: 1 x Passive Diaphragm Radiator Speaker Accessories Showcase Speaker Repair Parts
Out of stock2.8 inch SPI Touch Screen Module TFT Interface 240*320
[LED/LCD Display Module] This TFT display is big (2.8″ diagonal) bright and colorful! 240×320 pixels with individual RGB pixel control, this has way more resolution than a black and white 128×64 display. As a bonus, this display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen. This display has a controller built into it with RAM buffering so that almost no work is done by the microcontroller. The display can be used in two modes: 8-bit and SPI. For 8-bit mode, you’ll need 8 digital data lines and 4 or 5 digital control lines to read and write to the display (12 lines total). SPI mode requires only 5 pins total (SPI data in, data out, clock, select, and d/c) but is slower than the 8-bit mode. In addition, 4 pins are required for the touchscreen (2 digital, 2 analogs). This 2.8 inch SPI Touch Screen Module is wrapped up into an easy-to-use breakout board, with SPI connections on one end and 8-bit on the other. Both are 3-5V compliant with high-speed level shifters so you can use with any microcontroller. If you’re going with SPI mode, you can also take advantage of the onboard MicroSD card socket to display images. Stock version: 1.1V For more displays click below, LED/LCD Display Features : It shows the color depth of 262K/65K. Need at least 4 IOs from your MCU The display has a wide viewing angle. Big display with good resolution. Package Includes : 1 x 2.8-inch SPI Touch Screen Module TFT Interface 240 x 320 1 x Stylus Pen Buy other components to attach to this LCD Display Arduino Boards Raspberry Pi Dupont Cables
XH-M312 TPA3118D2 45W*2 Digital Amplifier Board Dual Channel Audio Amplifier Board Module
[Amplifier Board] Description XH-M312 TPA3118D2 Dual-Channel Digital Amplifier Board – 45W Output Upgrade your audio experience with the XH-M312 Digital Amplifier Board, powered by the advanced TPA3118D2 digital amplifier chip. This high-performance board delivers 45W output per channel, offering exceptional audio clarity and power. Designed for hobbyists and audio enthusiasts, it features user-friendly terminal blocks, making it a perfect ready-to-use solution for your electronic projects. Key Features: Powerful Dual-Channel Output: Delivers 45W per channel, perfect for driving a pair of 30W double speakers. Advanced Protection Mechanisms: Built with a brand-new C chip that includes: Over-voltage protection Over-current protection Over-heat protection Short-circuit protection This ensures reliable performance and longevity, even during demanding operations. Easy Connectivity: Equipped with 2P audio output terminals with a 5mm pitch, allowing secure and straightforward speaker connections. Versatile Application: Ideal for DIY audio projects, home audio systems, and electronic enthusiasts seeking high-quality sound performance. Compatibility: Perfect for superior audio output, making it suitable for custom speaker setups, audio experiments, or enhancing your existing audio systems. Boost Your Audio Performance Today! Bring your projects to life with the XH-M312 TPA3118D2 Dual-Channel Digital Amplifier Board—a reliable, high-power, and easy-to-use solution for outstanding sound quality. Why Choose the XH-M312 Amplifier Board? Whether you’re a seasoned DIYer or new to electronics, this amplifier board is built for convenience and reliability. The terminal block design simplifies connections, while the robust protection features safeguard your setup, ensuring worry-free operation. Package Includes: 1 x XH-M312 TPA3118D2 45W*2 Digital Amplifier Board