All products · 87 of 1440
Electronics, sensors, robotics kits, PC components, peripherals — everything Unik Systems carries, in one place.
Intel Core i5-13400F
10 cores (6P + 4E), 16 threads. 2.5 / 4.6 GHz. Strong all-rounder — gaming, light content creation, productivity.
Out of stockESD Anti-Static Wrist Strap
Adjustable wrist strap with 1.8 m grounding cord. PC build essential.
Out of stockESD Anti-Static Mat 600×400 mm
Grounded ESD work mat with snap stud for wrist strap. PCB / SMD work.
Out of stock0.96 Inch Blue SPI OLED Display Module 7-Pin 128×64 – SSD1306
[LED/LCD Display] 0.96 Inch Blue SPI OLED Display Module 7-Pin 128×64 – SSD1306 The 0.96-inch Blue OLED Display Module is a compact graphical display based on the SSD1306 driver IC, featuring a 128×64 pixel resolution and blue monochrome display. This version has a 7-pin interface with a dedicated CS (Chip Select) pin, making it suitable for 4-wire SPI communication. The module is factory-configured for SPI and can also be modified for I2C/IIC communication on compatible board versions. With its compact size, wide viewing angle and low-power OLED technology, it is suitable for Arduino, ESP32, ESP8266, STM32, Raspberry Pi and other microcontroller projects. ⭐ Key Features 0.96-inch blue OLED display 128 × 64 pixel resolution SSD1306 driver IC 7-pin interface Dedicated CS (Chip Select) pin Factory configured for 4-wire SPI Supports SPI and I2C/IIC with appropriate configuration 3.3V/5V compatible on supported module versions No backlight required Low power consumption Wide viewing angle of more than 160° Compact PCB design Pre-soldered 7-pin male header Compatible with Arduino, ESP32, ESP8266, STM32 and Raspberry Pi projects 📋 Technical Specifications Display Type: OLED (Organic Light-Emitting Diode) Display Colour: Blue Display Size: 0.96 inch Driver IC: SSD1306 Resolution: 128 × 64 pixels Interface: SPI / I2C Default Interface: 4-wire SPI Input Voltage: 3.3V–5V Viewing Angle: >160° Module Dimensions: Approximately 27 × 27 × 4mm Operating Temperature: Approximately -30°C to +70°C Header: 7-pin male header, pre-soldered Display Type: Monochrome blue OLED 🔌 7-Pin Interface The 7-pin version provides the following connections: GND – Ground VCC – Power supply D0 / SCK / CLK – SPI clock D1 / MOSI / SDA – SPI data RES / RST – Display reset DC / A0 – Data/Command selection CS – Chip Select 🛠️ SPI Connection The module is normally supplied in 4-wire SPI configuration. For an Arduino Uno, a typical connection is: VCC → 5V GND → GND D0 → SCK / D13 D1 → MOSI / D11 RES → Digital I/O DC → Digital I/O CS → Digital I/O The dedicated CS pin allows the OLED to share the SPI bus with other devices such as SD cards or additional SPI peripherals. 🔄 I2C / IIC Configuration On compatible versions, the module can be converted from SPI to I2C by changing the appropriate resistor configuration on the PCB. The supplied board configuration may require: Moving the resistor from R3 to R1 Shorting R8 with solder Using D0 as SCL Using D1 as SDA Configuring DC for the I2C address The exact resistor positions can vary between board revisions, so check the markings on your particular PCB before modification. 🎯 Applications Arduino projects ESP32 projects ESP8266 projects STM32 development Raspberry Pi projects IoT devices Sensor displays Voltage/current meters Battery monitors Temperature displays Digital clocks Data loggers Portable electronic devices Robotics DIY measuring instruments Embedded systems Menu and status displays 💡 Advantages of OLED OLED technology is self-emissive, meaning the pixels produce their own light and do not require a conventional backlight. This provides high contrast, compact construction and a wide viewing angle while keeping power consumption relatively low. ⚠️ Important Notes This is the 7-pin SPI version, not the 6-pin version. The module is normally configured for SPI communication. Check the PCB labels before connecting the module. Do not exceed the specified supply voltage. Although many versions support 5V operation, the exact voltage tolerance can vary between board revisions. I2C operation may require hardware resistor modification. The actual PCB layout and component markings may vary slightly between production batches. Display colour: Blue. Libraries such as Adafruit SSD1306 and U8g2 can be used with compatible microcontrollers. 📦 Package Includes 1 × 0.96 Inch Blue SPI OLED Display Module
26650 Battery Holder / Battery Spacer 2×1 – 26.3mm Bore Diameter
[Lithium Battery Holder] 26650 Battery Holder / Battery Spacer 2×1 – 26.3mm Bore Diameter The 26650 Battery Holder / Battery Spacer 2×1 is a cylindrical battery spacer designed to securely arrange 26650 lithium-ion battery cells while building multi-cell battery packs. Made from flame-retardant ABS+PC material, it provides a strong and stable structure while allowing air circulation around the cells. The holder features interlocking slots on the edges, allowing multiple spacers to be joined together to create different battery-pack sizes and configurations. After welding nickel strips, the assembled battery pack can achieve a solid and reliable structure without requiring additional connecting hardware. ⭐ Key Features Designed for 26650 cylindrical lithium-ion cells 2 × 1 configuration 26.3mm bore diameter Made from flame-retardant ABS+PC material High-temperature resistant construction Crack-resistant design Interlocking slots for connecting multiple spacers Allows flexible battery-pack configurations Provides mechanical support for battery cells Helps maintain proper spacing between cells Suitable for high-current battery-pack construction Helps improve battery-pack stability and reliability Allows airflow around the cells for heat dissipation 📋 Technical Specifications Product Type: Battery Holder / Battery Spacer Compatible Cell: 26650 cylindrical battery Configuration: 2 × 1 Number of Cells: 2 Bore Diameter: 26.3mm Material: Flame-retardant ABS+PC Construction: Interlocking modular design Mounting: Multiple spacers can be joined together Application: Lithium battery pack assembly Cell Type: Cylindrical Li-ion cells 🔧 Applications 26650 lithium-ion battery packs E-bike battery packs Electric scooter battery packs Electric vehicle battery packs Power-tool battery packs DIY high-current battery packs UPS battery systems Solar energy storage packs Portable power stations Robotics battery packs Custom lithium battery assemblies 🛠️ How to Use The spacer is designed to hold two 26650 cells in a 2×1 arrangement. Multiple spacers can be connected through the slots provided around the edges to create larger battery-pack configurations. For a complete battery pack: Cell → Spacer → Nickel Strip Welding → Additional Spacers → Battery Pack For mechanical support, spacers can be positioned at the top and bottom of the cells. Important: For each individual battery cell, 2 spacers are recommended—one at the top and one at the bottom. 💡 Advantages Simple Assembly: Easy to arrange cylindrical cells. Flexible Design: Multiple spacers can be interconnected to create different pack shapes. Strong Construction: Helps keep cells firmly positioned. Heat Dissipation: Provides spacing between cells and allows airflow. Reliable Battery Pack: Helps make the completed pack mechanically stable. Suitable for Complex Packs: Useful for custom battery configurations, including e-bike and high-current applications. ⚠️ Important Notes This product is only a battery holder/spacer; batteries are not included. The 26.3mm bore is intended for compatible 26650 cells. Check your actual cell diameter before purchase. Do not force oversized cells into the holder. Battery cells should be properly insulated and securely assembled. Use suitable nickel strip and an appropriate spot-welding method. Use a suitable BMS/protection system for the completed lithium battery pack. Battery cells should be properly matched before assembling a multi-cell pack. 2 spacers are recommended per individual cell, one on each end. Keep the battery assembly away from excessive heat, moisture and physical damage. 📦 Package Includes 1 × 26650 Battery Holder / Battery Spacer – 2×1, 26.3mm Bore Diameter Note: Battery cells, nickel strips and BMS are not included.
Out of stockGold AP-55 TPA3116D2 2×50W Bluetooth Stereo Digital Amplifier Board with USB, TF Card, FM & Remote
[Amplifier Board] Gold AP-55 TPA3116D2 2×50W Bluetooth Stereo Digital Amplifier Board with USB, TF Card, FM & Remote The Gold AP-55 is a compact Class-D stereo digital audio amplifier board based on the TPA3116D2 amplifier IC, designed for DIY Bluetooth speakers, home audio systems, portable speakers, bookshelf speakers, multimedia systems, and custom audio projects. Available product listings consistently identify the AP-55 as a dual-channel 50W + 50W amplifier, with a DC input range around 8–24V or 12–24V depending on the listing/version. The AP-55 combines the power amplifier with a multimedia player supporting Bluetooth 5.0, USB, TF/SD card, FM radio and AUX input. The Bluetooth device name is reported as GD-82EM, while the FM tuner covers 87.5–108.0MHz. It also includes an infrared remote control and a digital display for convenient operation. The TPA3116D2 Class-D amplifier provides efficient stereo amplification, making the board suitable for building compact but powerful audio systems. One detailed listing specifies support for 4Ω–8Ω speakers, with the commonly advertised maximum output of 50W per channel. ⭐ Key Features Gold AP-55 amplifier module TPA3116D2 Class-D amplifier IC 50W + 50W dual-channel stereo output Supports 4Ω–8Ω speakers Bluetooth 5.0 wireless audio Bluetooth device name: GD-82EM Built-in USB music player Built-in TF / SD card player Built-in FM radio FM frequency range 87.5–108.0MHz 3.5mm AUX input Infrared remote control Digital display Supports MP3 / WMA / WAV Power-off memory function Remembers the previous song and volume Compact design for DIY speaker projects High-efficiency Class-D amplification 📋 Technical Specifications Product Type: Stereo Class-D Digital Amplifier Board Model: Gold AP-55 Amplifier IC: TPA3116D2 Amplifier Class: Class-D Number of Channels: 2 / Stereo Output Power: 50W + 50W Maximum Total Output: 100W Speaker Impedance: 4Ω–8Ω Input Voltage: DC 8–24V (some listings specify 12–24V; verify the exact board version before use) Bluetooth Version: 5.0 Bluetooth Name: GD-82EM Bluetooth Range: Up to approximately 10–15m under suitable conditions Audio Formats: MP3 / WMA / WAV USB Support: Yes TF/SD Card Support: Yes FM Radio: Yes FM Frequency: 87.5–108.0MHz AUX Input: 3.5mm / Wired Audio Input Remote Control: IR Remote Remote Range: Approximately 4–7m Display: Digital Display Power-Off Memory: Yes Memory Function: Last song and volume Audio Input Modes: Bluetooth / USB / TF Card / FM / AUX Output: Dual-Channel Stereo Efficiency: Greater than 90% according to one detailed listing SNR: Approximately 102dB according to one detailed listing Distortion: Below 0.1% at normal listening levels according to one detailed listing Board Size: Approximately 70 × 50 × 20mm with shell, according to one listing 🎵 Audio & Playback Functions The AP-55 can switch between Bluetooth, USB, TF/SD Card, FM Radio and AUX sources. When Bluetooth mode is selected, users can pair a phone or other compatible device with GD-82EM. USB and TF/SD cards can be used for local music playback, while AUX provides a wired audio input. 📻 FM Radio The built-in FM tuner supports the 87.5–108.0MHz broadcast band. FM stations can be searched and selected using the onboard controls or remote control. 🎛️ Controls & Remote The module provides controls for functions such as previous track, next track, volume up, volume down, play/pause, mode selection and FM station selection. The infrared remote provides additional wireless control of playback, volume, mode and other supported functions. 🔧 Applications DIY Bluetooth Speakers High-Power Bluetooth Speaker Projects Portable Speaker Systems Bookshelf Speaker Systems Home Audio Projects Multimedia Speaker Systems USB MP3 Speaker Systems TF/SD Card Music Players FM Radio Speaker Projects Car Audio Projects Custom Wooden Speaker Cabinets Desktop Audio Systems Electronics DIY Projects 🛠️ Installation Connect a suitable DC power supply within the specified voltage range and observe the correct polarity. Connect the left and right speaker outputs to compatible 4Ω–8Ω speakers. Select Bluetooth, USB, TF/SD, FM or AUX according to the desired audio source. For maximum advertised output, a suitable 24V high-current power supply is recommended by one vendor; at lower supply voltages, available output power will be lower. 📦 Package Includes 1 × Gold AP-55 TPA3116D2 2×50W Bluetooth Amplifier Board 1 × IR Remote Control 1 × Required Connecting Wires/Cables (package contents may vary by seller/version) ⚠️ Precautions Verify the exact input voltage requirement of your AP-55 version before powering it. Do not exceed 24V DC where the board specification limits input to 24V. Check power polarity carefully before connection. Use speakers with a compatible 4Ω–8Ω impedance. Do not short-circuit the speaker output terminals. Ensure adequate ventilation during high-power operation. Use a suitable high-current power supply for high-output operation. Do not connect the speaker outputs together or directly to ground. Keep the board away from moisture and conductive materials. Incorrect wiring or excessive voltage can permanently damage the amplifier IC.
1K Ohm Rotary Potentiometer Round Shaft 3 Pin Elcon
[Potentiometer] 1KΩ Rotary Potentiometer Round Shaft Elcon The 1KΩ Rotary Potentiometer Round Shaft Elcon is a reliable 3-pin linear rotary potentiometer designed for adjusting electrical parameters such as voltage, current, brightness, motor speed, and other control functions in electronic circuits. By rotating the shaft, the resistance can be smoothly adjusted across its available range, making it suitable for a wide variety of DIY and electronic applications. With its compact 16mm body, 6mm round shaft, and through-hole mounting design, this potentiometer is easy to install on electronic PCBs and control panels. Its linear resistance characteristics make it suitable for applications such as LED brightness control, fan speed control, motor control, power supply adjustment, and general-purpose voltage control. ⭐ Key Features 1KΩ resistance value 3-pin rotary potentiometer Linear potentiometer Smooth rotary adjustment 6mm round shaft 10mm shaft length Compact 16mm body diameter Through-hole mounting Suitable for PCB and electronic circuits Ideal for voltage and resistance adjustment Suitable for DIY and electronic projects Elcon brand 📋 Technical Specifications Product Type: Rotary Potentiometer Brand: Elcon Resistance Value: 1KΩ Configuration: 3 Pin / Single Gang Tolerance: ±20% Shaft Type: Round Shaft Shaft Diameter: 6mm Shaft Length: 10mm Body Diameter / Width: 16mm Total Height: Approx. 25mm Mounting Type: Through Hole Operating Temperature: -40°C to +80°C Weight: Approx. 8g 🔧 Applications LED Brightness Control Fan Speed Control Motor Speed Control Voltage Adjustment Current Adjustment Power Supply Circuits Audio & Electronic Circuits Arduino Projects DIY Electronics Projects Electronic Prototyping 🛠️ How It Works A potentiometer is a variable resistor with three terminals. The two outer terminals are connected to the resistive track, while the center terminal acts as the wiper. Rotating the shaft changes the wiper position and therefore changes the resistance or output voltage in the circuit. 📦 Package Includes 1 × 1KΩ Rotary Potentiometer Round Shaft Elcon ⚠️ Note Product images are shown for illustrative purposes only and may differ slightly from the actual product. The 1KΩ value, tolerance, dimensions, and shaft length should be verified against the actual product batch before installation.
5K Ohms Rotary Potentiometer Round Shaft 3 Pin Elcon
[Potentiometer] 5KΩ Rotary Potentiometer Round Shaft Elcon The 5KΩ Rotary Potentiometer Round Shaft Elcon is a reliable 3-pin linear rotary potentiometer designed for adjusting electrical parameters such as voltage, current, brightness, motor speed, and other control functions in electronic circuits. By rotating the shaft, the resistance can be smoothly adjusted across its available range, making it suitable for a wide variety of DIY and electronic applications. With its compact 16mm body, 6mm round shaft, and through-hole mounting design, this potentiometer is easy to install on electronic PCBs and control panels. Its linear resistance characteristics make it suitable for applications such as LED brightness control, fan speed control, motor control, power supply adjustment, and general-purpose voltage control. ⭐ Key Features 5KΩ resistance value 3-pin rotary potentiometer Linear potentiometer Smooth rotary adjustment 6mm round shaft 13mm shaft length Compact 16mm body diameter Through-hole mounting Suitable for PCB and electronic circuits Ideal for voltage and resistance adjustment Suitable for DIY and electronic projects Elcon brand 📋 Technical Specifications Product Type: Rotary Potentiometer Brand: Elcon Resistance Value: 5KΩ Configuration: 3 Pin / Single Gang Tolerance: ±20% Shaft Type: Round Shaft Shaft Diameter: 6mm Shaft Length: 13mm Body Diameter / Width: 16mm Total Height: Approx. 28mm Mounting Type: Through Hole Operating Temperature: -40°C to +80°C Weight: Approx. 8g 🔧 Applications LED Brightness Control Fan Speed Control Motor Speed Control Voltage Adjustment Current Adjustment Power Supply Circuits Audio & Electronic Circuits Arduino Projects DIY Electronics Projects Electronic Prototyping 🛠️ How It Works A potentiometer is a variable resistor with three terminals. The two outer terminals are connected to the resistive track, while the center terminal acts as the wiper. Rotating the shaft changes the wiper position and therefore changes the resistance or output voltage in the circuit. 📦 Package Includes 1 × 5KΩ Rotary Potentiometer Round Shaft Elcon ⚠️ Note Product images are shown for illustrative purposes only and may differ slightly from the actual product. The 5KΩ value, tolerance, dimensions, and shaft length should be verified against the actual product batch
2.25 Inch 4 Ohm 10 Watt Full Range Speaker with Neodymium Magnet
[Speakers] 2.25-Inch Speaker Driver • 4 Ohm Impedance • 10W Power Rating • Neodymium Magnet • Compact Full Range Audio Speaker The 2.25 Inch 4 Ohm 10 Watt Full Range Speaker with Neodymium Magnet is a compact and high-performance speaker driver designed for portable audio systems, DIY speaker projects, multimedia devices, embedded electronics, and custom sound enclosures. Featuring a powerful neodymium magnet, this speaker delivers clear vocals, balanced midrange, and improved bass response while maintaining a lightweight and compact design. With a 4 ohm impedance and 10 watt power rating, the speaker is suitable for use with small audio amplifiers, Bluetooth amplifier modules, DIY portable speakers, mini sound systems, toys, alarm systems, educational kits, and embedded electronic devices. The full-range design allows it to reproduce a wide spectrum of audio frequencies without requiring additional tweeters for many compact applications. Its durable construction and lightweight neodymium magnet assembly make it ideal for applications where both performance and space efficiency are important. ⭐ Features Compact 2.25-inch full range speaker Powerful neodymium magnet 4 ohm impedance 10 watt power rating Clear and balanced sound output Enhanced vocal clarity and midrange performance Lightweight and compact construction Easy to mount in custom enclosures Suitable for portable and embedded audio systems Ideal for DIY electronics and audio projects 📋 Technical Specifications Product Type: Full Range Speaker Driver Speaker Size: 2.25 Inch Impedance: 4 Ohm Power Rating: 10 Watt Magnet Type: Neodymium Speaker Type: Full Range Mounting Type: Enclosure / Panel Mount Application Type: Audio Output Frame Material: Metal Cone Material: Paper Composite Color: Black 🔧 Applications Suitable for: Portable Speaker Systems Bluetooth Speakers DIY Audio Projects Mini Sound Systems Multimedia Devices Toys and Educational Kits Alarm and Notification Systems Embedded Electronic Devices Mini Amplifiers Sound Modules Intercom Systems Custom Speaker Enclosures Robotics and Electronics Projects 📦 Package Includes 1 × 2.25 Inch 4 Ohm 10 Watt Full Range Speaker with Neodymium Magnet ⚠️ Precautions Do not exceed the 10W rated power. Use an amplifier compatible with 4 ohm speakers. Avoid exposure to moisture, water, and excessive dust. Mount the speaker securely to minimize unwanted vibration. Do not apply direct pressure to the speaker cone or surround.
Passive Radiator Bass Diaphragm Rubber Speaker Vibration Plate for DIY Speakers
[Passive Radiator] 🔊 Oval, Square & Round Passive Radiator Bass Diaphragm Rubber Speaker Vibration Plate for DIY Speakers Deep Bass Enhancement • Passive Design • No External Power Required • Ideal for DIY Speaker Projects The Rubber Passive Radiator Bass Diaphragm is a high-quality auxiliary bass vibration plate designed to significantly improve the low-frequency response of speaker systems. Available in Oval, Square, and Round shapes with multiple sizes, this passive radiator enhances bass performance without requiring additional power or amplifier channels. Unlike conventional speakers, a passive radiator does not contain a voice coil or magnet. Instead, it utilizes the air pressure generated by the active speaker driver to vibrate, producing deeper, richer bass while minimizing distortion and unwanted cabinet resonance. Manufactured using premium rubber and durable ABS materials, these passive radiators provide excellent flexibility, durability, and long service life. They are ideal for upgrading Bluetooth speakers, portable speakers, multimedia speakers, subwoofers, soundbars, and custom DIY audio projects. Whether you're repairing an existing speaker or building a custom enclosure, these passive bass diaphragms help deliver powerful low-frequency performance while maintaining compact enclosure sizes. ⭐ Features Premium quality rubber passive radiator Available in Oval, Square & Round shapes Produces deep and powerful bass response No power supply or wiring required Improves low-frequency performance Reduces speaker distortion Durable rubber suspension Lightweight and compact design Easy to install Ideal for DIY speaker upgrades and repairs 📋 Technical Specifications Product Type: Passive Radiator Bass Diaphragm Material: Rubber + ABS Plastic+Metal Shape: Oval / Square / Round (Depending on Selected Variant) Available Sizes: Multiple Sizes (2040 to 6090 Series) Operation: Passive (No Voice Coil or Magnet) Power Requirement: None Installation Type: Speaker Cabinet Mount Application: Low Frequency Bass Enhancement Color: Black 🔧 Applications Suitable for: Bluetooth Speakers Portable Speakers DIY Speaker Projects Multimedia Speakers Home Audio Systems Bookshelf Speakers Soundbars Subwoofers Wireless Speakers Audio System Repairs Custom Speaker Cabinets DIY Audio Enclosures 📦 Package Includes 1 × Passive Radiator Bass Diaphragm (Size & Shape as Selected) ⚠️ Note This is a passive radiator only and does not contain a voice coil, magnet, or electrical terminals. Product images are for reference only. The actual product may vary slightly in appearance depending on the selected size, shape, or manufacturing batch.
ESP32-C3 Super Mini Development Board With Headers Pins
[ESP Modules] Ultra Compact • Wi-Fi & BLE 5.0 • USB Type-C • Perfect for IoT & Embedded Projects The ESP32-C3 Super Mini Development Board is a compact, feature-rich development board built around the powerful ESP32-C3 SoC from Espressif. Powered by a 32-bit RISC-V single-core processor running at up to 160MHz, it combines 2.4GHz Wi-Fi, Bluetooth 5.0 Low Energy (BLE), and low-power operation in an ultra-small form factor. Designed for IoT, smart home, wireless communication, automation, and embedded system development, the ESP32-C3 Super Mini offers 4MB Flash memory, 400KB SRAM, multiple GPIOs, ADC, PWM, UART, SPI, and I2C interfaces for connecting sensors, displays, relays, and other peripherals. The onboard USB Type-C interface simplifies programming and power supply, while the built-in USB-to-Serial functionality enables quick firmware uploading without requiring additional programmers. Fully compatible with Arduino IDE, ESP-IDF, PlatformIO, and MicroPython, it is suitable for beginners, students, makers, and professional developers. Its ultra-compact breadboard-friendly design makes it ideal for portable and space-constrained projects where performance, wireless connectivity, and energy efficiency are essential. Note: Programming, software configuration, driver installation, firmware flashing, and coding-related issues are not covered under return or replacement. Users are expected to troubleshoot software-related issues independently. ⭐ Features Powerful ESP32-C3 32-bit RISC-V processor CPU frequency up to 160MHz Built-in 2.4GHz Wi-Fi (802.11 b/g/n) Integrated Bluetooth 5.0 Low Energy (BLE) Ultra-compact Super Mini design Breadboard-friendly layout USB Type-C interface for programming and power 4MB onboard Flash memory 400KB SRAM Multiple GPIO, ADC, PWM, UART, SPI & I2C interfaces Low power consumption with Deep Sleep mode Onboard programmable LED Compatible with Arduino IDE, ESP-IDF, PlatformIO & MicroPython Ideal for IoT, automation, robotics, and wireless applications 📋 Technical Specifications Product Type: Development Board Board Model: ESP32-C3 Super Mini Microcontroller: ESP32-C3 Processor Architecture: 32-bit RISC-V CPU Frequency: Up to 160MHz Core: Single Core Flash Memory: 4MB SRAM: 400KB Wi-Fi Standard: IEEE 802.11 b/g/n (2.4GHz) Bluetooth: Bluetooth 5.0 Low Energy (BLE) Operating Voltage: 3.3V Input Voltage: 5V via USB Type-C or 3.3V External USB Interface: USB Type-C GPIO: Multiple Digital GPIO Pins Analog Input: Up to 6 ADC Channels PWM: Supported UART: Supported SPI: Supported I2C: Supported USB-to-Serial: Onboard Onboard LED: User Programmable (GPIO8) Power Consumption: Ultra Low (Deep Sleep ≈ 43µA) Dimensions: Approx. 22.5 × 18 mm Headers: Pre-Soldered 🔧 Applications Suitable for: Internet of Things (IoT) Smart Home Automation Wireless Sensor Networks Home Automation Systems Bluetooth Low Energy Devices Wi-Fi Enabled Controllers Robotics Projects Data Logging Systems Remote Monitoring Industrial Automation Portable Embedded Devices Educational Learning DIY Electronics Projects Wearable Electronics Rapid Prototyping 📦 Package Includes 1 × ESP32-C3 Super Mini Development Board Pin Headers ⚠️ Note Programming, firmware installation, software configuration, and driver-related issues are not covered under warranty, return, or replacement. Please verify board compatibility and install the appropriate development environment before programming. Soldered and non-soldered header pin depend on stock
DHT11 Digital Temperature and Humidity Sensor Module 3.3V-5V for Arduino & Raspberry Pi
[Temperature Sensor] The DHT11 Digital Temperature and Humidity Sensor Module is a reliable and cost-effective sensor designed to measure ambient temperature and relative humidity. It combines a capacitive humidity sensing element and a thermistor with a built-in digital signal processing unit, providing calibrated digital output directly to microcontrollers. In addition, the DHT11 offers stable performance and excellent long-term reliability, making it suitable for environmental monitoring and automation applications. As a result, it is widely used in weather stations, smart home systems, greenhouse monitoring, HVAC systems, and educational electronics projects. Because the module includes the required pull-up resistor, interfacing with microcontrollers becomes simple and straightforward. Furthermore, only three connections are required: VCC, GND, and Data Output. The sensor operates from a wide voltage range of 3.3V to 5.5V DC, ensuring compatibility with Arduino, Raspberry Pi, ESP32, STM32, NodeMCU, and other development boards. Moreover, readily available libraries and example codes allow quick integration into projects. The DHT11 utilizes advanced digital signal acquisition technology and dedicated temperature-humidity sensing techniques to ensure accurate and dependable measurements. 🔹 Key Features Measures temperature and humidity simultaneously Calibrated digital signal output Low power consumption High reliability and long-term stability Capacitive humidity sensing technology Built-in pull-up resistor on module Compatible with Arduino, ESP32, Raspberry Pi, and STM32 Simple 3-wire interface Easy integration into IoT projects Compact and lightweight design 🔹 Technical Specifications Sensor Model: DHT11 Operating Voltage: 3.3V – 5.5V DC Output Type: Digital Serial Output Humidity Measurement Range: 20%RH – 90%RH Humidity Accuracy: ±5%RH Humidity Resolution: 1%RH Temperature Measurement Range: 0°C – 50°C Temperature Accuracy: ±2°C Temperature Resolution: 1°C Sampling Rate: 1Hz (One Reading Per Second) Long-Term Stability: < ±1%RH/Year Interchangeability: Fully Interchangeable Sensor Technology: Capacitive Humidity Sensor + Thermistor 🔹 Pin Configuration Pin 1 (VCC): 3.3V – 5.5V DC Power Supply Pin 2 (DATA): Digital Serial Data Output Pin 3 (GND): Ground 🔹 Applications This sensor module is suitable for: Arduino projects Raspberry Pi projects ESP32 projects IoT systems Weather monitoring stations Smart home automation Greenhouse monitoring HVAC control systems Environmental monitoring Educational electronics projects 🔹 Package Includes 1 × DHT11 Digital Temperature and Humidity Sensor Module
220-240V AC Swing Motor Gear Motor for Air Cooler Synchronous Motor
[AC Motor] The 220-240V AC Swing Motor Gear Motor is a compact synchronous motor specially designed for air cooler oscillation and swing movement applications. It delivers smooth and stable low-speed rotation, making it ideal for automatic airflow control systems. In addition, the motor operates directly on standard 220-240V AC power, eliminating the need for external driver circuits. As a result, it can be easily integrated into household appliances and industrial cooling equipment. Because of its synchronous motor design, the motor maintains stable rotational speed based on the AC supply frequency. Furthermore, the built-in gear reduction mechanism provides controlled torque and smooth swing movement with low noise operation. The motor is designed for continuous duty applications and features low power consumption with reliable long-term performance. Moreover, the compact body and screw-mount design allow quick installation and easy replacement in air coolers and oscillation systems. This synchronous swing motor is widely used in air coolers, ventilation systems, oscillating fans, automation projects, and household appliances. 🔹 Key Features Designed for air cooler swing operation Operates directly on 220-240V AC supply Smooth synchronous gear motor operation Stable low-speed rotation Low noise and low power consumption Compact and lightweight construction Durable internal gear mechanism Suitable for continuous operation 🔹 Technical Specifications Product Type: AC Synchronous Swing Motor Motor Type: Gear Reduction Synchronous Motor Operating Voltage: 220V–240V AC Rated Frequency: 50/60Hz Rotation Speed: Typically 4–6 RPM (depends on model) Power Consumption: Approx. 4W–5W Rotation Direction: CW / CCW Gear Mechanism: Internal Reduction Gear Shaft Type: Metal Round-Shaft Mounting Type: Screw Mount Insulation Class: Class E Body Material: Metal + Plastic Operating Temperature: -10°C to +55°C Noise Level: Low Noise Operation Duty Cycle: Continuous Duty Application Type: Swing / Oscillation Mechanism 🔹 Working Principle This motor works using synchronous AC motor technology, where the rotor rotates according to the AC supply frequency. The internal reduction gears decrease the motor speed while increasing torque, allowing smooth and controlled oscillation movement. 🔹 Applications This swing motor is suitable for many electrical and mechanical applications, including: Air coolers Oscillating fans Ventilation systems Swing control mechanisms Household appliances Automation systems DIY electronics projects 🔹 Package Includes 1 × 220-240V AC Swing Motor Gear Motor
ZK-MT21 bluetooth 5.0 Subwoofer Amplifier Board 50WX2+100W 2.1 Channel Power Audio Stereo Amplifier Tone Board Bass AMP AUX
[Amplifier Board] ZK-MT21 2.1 Channel Bluetooth 5.0 Audio Amplifier Module – 50W × 2 + 100W Subwoofer The ZK-MT21 2.1 Channel Bluetooth Audio Amplifier Module is a compact high-power stereo amplifier board designed for DIY Bluetooth speaker and home audio projects. It supports Bluetooth 5.0 and AUX audio input and provides dedicated left, right and subwoofer channels with adjustable volume, bass, treble, subwoofer volume and subwoofer frequency controls. With a suitable DC power supply and properly matched speakers, the module can deliver up to 50W + 50W for the left/right channels and up to 100W for the subwoofer channel. The board includes protection against reverse connection, overheating, overcurrent and short circuit. ⭐ Key Features Model: ZK-MT21 2.1 channel stereo audio amplifier Bluetooth 5.0 wireless audio input Bluetooth transmission distance up to approximately 15 meters under suitable conditions AUX wired audio input Left + Right + Subwoofer output Output up to 50W × 2 + 100W subwoofer Supports 4Ω–8Ω speakers Adjustable main volume Adjustable bass and treble for left/right channels Adjustable subwoofer volume Adjustable subwoofer frequency Subwoofer frequency adjustment range 20Hz–200Hz Reverse-polarity protection Overheat protection Overcurrent protection Short-circuit protection Compact amplifier board design Suitable for DIY Bluetooth speaker projects 📋 Technical Specifications Product Name: 2.1 Channel Audio Amplifier Module Model: ZK-MT21 Bluetooth Version: 5.0 Bluetooth Range: Approximately 15m Bluetooth Shielding: No shielding Audio Input: AUX + Bluetooth Channel: 2.1 Input Sensitivity: 500mV Amplifier Chip Solution: Domestic power amplifier chip Power Supply: DC 12–24V Recommended Supply Current: 5A or above Left Channel Output: <50W Right Channel Output: <50W Subwoofer Output: <100W Total Configuration: 50W × 2 + 100W Compatible Speaker Impedance: 4–8Ω Recommended Speaker Power: 20–100W Subwoofer Frequency Adjustment: 20Hz–200Hz Product Dimensions: 93 × 90 × 22mm Package Weight: Approximately 185g Protection: Reverse connection, overheat, overcurrent and short circuit ⚠️ Power Supply Warning:Do not connect this module directly to a 24V battery pack. Use a suitable regulated DC power supply as specified for the module. 🎛️ Control Functions MAIN-VOLUME: Controls the overall volume of the left, right and subwoofer channels. R&L CHANNEL-BASS: Adjusts bass level for the left and right channels. R&L CHANNEL-TREBLE: Adjusts treble level for the left and right channels. SUBWOOFER-VOLUME: Controls the subwoofer volume. SUBWOOFER-FREQ: Adjusts the subwoofer cutoff frequency from approximately 20Hz to 200Hz. 🔊 Speaker Selection Left and right channels can be connected to 4Ω–8Ω full-range or mid/high-frequency speakers. Recommended speaker power is 20W–100W. The subwoofer output should be connected to a suitable subwoofer speaker, not a regular full-range speaker. The subwoofer should have suitable low-frequency performance, with the source information recommending a frequency capability of at least 50Hz. Speaker impedance and power should be matched correctly with the amplifier. 🔌 Power Supply Selection The power supply is important for achieving proper amplifier performance and sound quality. A power supply with excessive ripple may increase background noise. Recommended supply: 18V / 19V / 24V with current above 5A Lower-voltage or lower-current supplies can be used, but available output power will be reduced. Insufficient supply current can cause voltage drop, abnormal operation or poor sound quality. If the amplifier is operated near maximum volume, an inadequate power supply may result in distortion. The power supply should have sufficient capacity for the actual amplifier load. Higher supply voltage can provide greater available output power within the module's specified operating range. 📱 Bluetooth & AUX Input The ZK-MT21 provides two audio input methods: Bluetooth Bluetooth 5.0 wireless audio input Bluetooth is the preferred input mode according to the supplied product information. Bluetooth supports automatic reconnection. Once Bluetooth is successfully connected, the module operates in Bluetooth mode. AUX Connect an external audio source through the AUX input. When using AUX, ensure the Bluetooth connection has been disconnected if necessary. 🔧 Applications DIY Bluetooth speakers 2.1 channel speaker systems Home audio projects Portable audio systems Subwoofer amplifier projects Custom speaker cabinets Desktop speaker systems Multimedia speaker systems Electronics and audio DIY projects Replacement/custom amplifier systems 🛠️ Installation & Usage Connect a suitable DC 12–24V power supply to the amplifier module. Connect the left and right speakers to their respective output terminals. Connect a suitable subwoofer to the subwoofer output. Ensure the speaker impedance is within the supported 4–8Ω range. Connect the audio source through Bluetooth or AUX. Adjust the main volume, bass, treble, subwoofer volume and frequency according to your requirements. Start with a low volume and gradually increase it. Ensure adequate ventilation and heat dissipation during high-power operation. ⚠️ Important Precautions Do not connect directly to a 24V battery pack. Use a suitable regulated DC power supply. Do not reverse the power supply polarity. Do not short-circuit the speaker outputs. Do not exceed the recommended speaker power and impedance. Ensure the power supply can provide sufficient current. Insufficient power may cause distortion or abnormal operation. Excessive load can cause the amplifier to heat up and activate thermal protection. Provide adequate ventilation during high-power operation. If distortion occurs at high volume, reduce the volume or use a more suitable power supply. The amplifier's actual output depends on the power supply, speaker impedance, audio input and overall system configuration. 📦 Package Includes 1 × ZK-MT21 Bluetooth 5.0 2.1 Channel Audio Amplifier Module
Type-C USB Input High Current 3A Polymer Ternary Lithium Battery Quick Fast Charging Board IP2312 CC/CV Mode 5V To 4.2V
[Lithium Battery Protection Board] Power your projects with the Type-C USB Input 3A Lithium Battery Fast Charging Board (IP2312) — a compact, high-efficiency charging solution designed for 3.7V lithium-ion and lithium polymer batteries. Built around the advanced IP2312 main control chip, this module delivers fast, stable, and intelligent charging using a full CC/CV (Constant Current / Constant Voltage) charging algorithm. It ensures optimal battery health, safety, and performance while supporting high current charging up to 3A, making it ideal for modern DIY electronics and portable power applications. The Type-C input interface provides universal compatibility with standard 5V USB power sources, while onboard indicator LEDs clearly display charging status. ⚠️ Note: Not suitable for 3.2V LiFePO4 (Lithium Iron Phosphate) batteries Key Features ⚡ High Current Fast Charging (Up to 3A)Supports rapid charging for lithium-ion/polymer batteries, reducing charging time significantly. 🔋 Advanced CC/CV Charging TechnologyEnsures safe and efficient charging with automatic switching between charging stages. 🔌 Type-C USB InputModern and widely compatible input interface (4.5V–5.5V), easy to power from adapters, power banks, or USB ports. 🧠 Smart Charging Management (IP2312 Chip)Automatically adjusts charging mode based on battery voltage for maximum safety and efficiency. 🔴🔵 LED Status Indicators Red LED: Charging in progress Blue LED: Fully charged 🛠️ Compact & Easy IntegrationSmall size makes it perfect for embedded systems, DIY battery packs, and portable devices. Charging Working Principle 🔹 Trickle Charging Mode (< 3V)When battery voltage is below 3V, the module charges with a safe low current (~100mA). 🔹 Constant Current Mode (> 3V)Once voltage exceeds 3V, it switches to constant current charging (up to 3A). 🔹 Constant Voltage Mode (~4.2V)As the battery approaches full charge, it maintains voltage while gradually reducing current. 🔹 Auto Cut-Off & Recharge Charging stops when current drops below 300mA Automatically resumes charging if voltage drops below 4.1V Specifications Specification Description Main Chip IP2312 Charging Mode CC/CV (Constant Current / Voltage) Input Voltage 4.5V – 5.5V (Type-C USB) Charging Current Up to 3A Battery Type 3.7V Li-ion / Li-Po Cut-off Voltage 4.2V / 4.35V Indicator LEDs Red (Charging), Blue (Full) Dimensions 34.5mm × 15mm Applications 🔋 DIY lithium battery packs🔌 Power bank projects🚗 Portable electronics & gadgets🔧 Arduino / ESP32 battery systems🔦 Rechargeable lighting systems📦 Embedded battery charging modules Package Includes 1 × Type-C USB 3A Lithium Battery Fast Charging Board (IP2312)
1S 2A 18650 (NMC) Lithium Battery BMS Round Shape With Nickel Strip
[Lithium Battery Protection Board] JLGW BMS NMC 1S 2A ROUND Hardware Product Data Sheet The BMS NMC 1S 2A ROUND (JLGW) is a high-precision, compact Battery Management System specially designed for single-cell NMC (Li-ion 3.7V) battery protection. This module is uniquely built in a round PCB layout, allowing it to seamlessly integrate into compact cylindrical battery designs or battery packs with limited space. Technical Specifications Parameter Specification Configuration 1S (Single 3.7V Li-ion Cell) Battery Chemistry NMC / Li-ion Nominal Voltage 3.7V Continuous Current 2A Overcharge Protection 4.25V ± 0.05V Over-discharge Protection 2.75V ± 0.05V Short Circuit Protection Yes (Instant cut-off) Overcurrent Protection Yes (~3A threshold) Working Temperature Range -20°C to +60°C PCB Shape & Size Round mini-PCBA with dual nickel strips Mounting Style Spot-Weld Tabs Key Features Space-Saving Round Design: Engineered for cylindrical cells and compact builds. Intelligent Safety Circuitry: Built-in MOSFETs and ICs protect against all common faults. 2A Output: Suited for low-drain applications like wearables and IoT gadgets. Nickel Strips Included: Pre-attached nickel makes welding and integration seamless. Single Cell Protection: Manages charge-discharge cycles efficiently for 1S packs. Ideal Applications LED Flashlights Cylindrical Battery Packs DIY Battery Projects Bluetooth Audio Devices Small IoT Systems Mini Power Banks The PCM NMC 01S/2A ROUND is a Battery Protection Circuit Module (PCM) designed for 1 series Nickel Manganese Cobalt (NMC) battery packs, supporting a 2A continuous discharge current. This module is suitable for low-power applications such as small energy storage systems, backup power solutions, and portable devices. The round designation indicates that the PCM is designed for round-cell configurations, which are commonly used in battery packs for various consumer electronics. It offers essential protection features, including overcharge, over-discharge, overcurrent, short circuit, and temperature protection, ensuring the safe and reliable operation of the battery. The PCM helps maintain the health of the cells by balancing the voltage across them, optimizing performance and extending the battery's lifespan. Package Includes: 1 x 1S 2A 18650 (NMC) Lithium Battery BMS Round Shape With Nickel Strip
Crocodile Alligator Clip 50 mm Black and Red
Description: An alligator clip, also called a spring clip, creates a temporary electrical connection using a simple mechanical design.It gets its name because the jaws resemble an alligator or crocodile’s mouth, opening and closing to grip objects securely.The clip works like a spring-loaded clothespin that uses tapered, serrated jaws to hold wires or metal parts tightly.A spring pushes the jaws together, allowing the clip to grip objects and maintain a reliable electrical connection.Manufacturers design these clips for electronics testing, enabling quick connections without soldering or permanent joints.One jaw usually connects to a wire by crimping or soldering for efficient current transfer.Some clips use a bent jaw forming the inner contact of a 15 mm to 4 mm female banana jack.This design allows a fast, non-permanent connection between test circuits and laboratory instruments.A plastic cover or boot surrounds the clip to prevent short circuits and protect users from accidental shocks.Engineers and students use these clips widely in testing, prototyping, and educational experiments. Applications: Technicians use small clips (15 mm–40 mm) in electrical laboratories, schools, and college labs for quick test connections.Large clips, called automotive clips or battery clamps, use solid copper for low resistance and strong current flow.Users connect these large clips with thick insulated copper cables between automobile batteries or heavy electrical systems.Hobbyists and professionals rely on these clips for safe, reusable, and efficient electrical connections. Product Example: Check the Crocodile Alligator Clip 50 mm – Red and Black, made from durable stainless steel with a protective plastic shroud.Its spring-loaded jaws open wide to grip different wire sizes securely during testing or circuit connection.The serrated teeth ensure a strong, slip-free grip that maintains stable electrical contact during operation. Package Includes: 1 × Crocodile Alligator Clip 50 mm (Black and Red)
100K Rotary Potentiometer Round Shaft Elcon
[Potentiometer] 100KΩ Rotary Potentiometer Round Shaft Elcon The 100KΩ Rotary Potentiometer Round Shaft Elcon is a reliable 3-pin linear rotary potentiometer designed for adjusting electrical parameters such as voltage, current, brightness, motor speed, and other control functions in electronic circuits. By rotating the shaft, the resistance can be smoothly adjusted across its available range, making it suitable for a wide variety of DIY and electronic applications. With its compact 16mm body, 6mm round shaft, and through-hole mounting design, this potentiometer is easy to install on electronic PCBs and control panels. Its linear resistance characteristics make it suitable for applications such as LED brightness control, fan speed control, motor control, power supply adjustment, and general-purpose voltage control. ⭐ Key Features 100KΩ resistance value 3-pin rotary potentiometer Linear potentiometer Smooth rotary adjustment 6mm round shaft 13mm shaft length Compact 16mm body diameter Through-hole mounting Suitable for PCB and electronic circuits Ideal for voltage and resistance adjustment Suitable for DIY and electronic projects Elcon brand 📋 Technical Specifications Product Type: Rotary Potentiometer Brand: Elcon Resistance Value: 100KΩ Configuration: 3 Pin / Single Gang Tolerance: ±20% Shaft Type: Round Shaft Shaft Diameter: 6mm Shaft Length: 13mm Body Diameter / Width: 16mm Total Height: Approx. 28mm Mounting Type: Through Hole Operating Temperature: -40°C to +80°C Weight: Approx. 8g 🔧 Applications LED Brightness Control Fan Speed Control Motor Speed Control Voltage Adjustment Current Adjustment Power Supply Circuits Audio & Electronic Circuits Arduino Projects DIY Electronics Projects Electronic Prototyping 🛠️ How It Works A potentiometer is a variable resistor with three terminals. The two outer terminals are connected to the resistive track, while the center terminal acts as the wiper. Rotating the shaft changes the wiper position and therefore changes the resistance or output voltage in the circuit. 📦 Package Includes 1 × 100KΩ Rotary Potentiometer Round Shaft Elcon ⚠️ Note Product images are shown for illustrative purposes only and may differ slightly from the actual product. The 100KΩ value, tolerance, dimensions, and shaft length should be verified against the actual product batch before installation.
10K Rotary Potentiometer Round Shaft 3Pin Elcon
[Potentiometer] 10KΩ Rotary Potentiometer Round Shaft Elcon The 10KΩ Rotary Potentiometer Round Shaft Elcon is a reliable 3-pin variable resistor designed for adjusting electrical parameters such as voltage, current, brightness, motor speed, and other control functions in electronic circuits. By rotating the shaft, the resistance can be smoothly adjusted across its available range, making it suitable for a wide variety of DIY and electronic applications. With its compact 16mm body, 6mm round shaft, and through-hole mounting design, this potentiometer is easy to install on electronic PCBs and control panels. The linear resistance characteristics make it particularly suitable for applications such as LED brightness control, fan speed control, motor control, and general-purpose voltage adjustment. ⭐ Key Features 10KΩ resistance value 3-pin rotary potentiometer Linear potentiometer Smooth rotary adjustment 6mm round shaft Compact 16mm body diameter Through-hole mounting Suitable for PCB and electronic circuits Useful for voltage and current adjustment Suitable for LED, fan and motor control applications Elcon brand 📋 Technical Specifications Product Type: Rotary Potentiometer Brand: Elcon Resistance Value: 10KΩ Configuration: 3 Pin / Single Gang Tolerance: ±20% Shaft Type: Round Shaft Shaft Diameter: 6mm Shaft Length: 13mm Body Diameter / Width: 16mm Total Height: 30mm Mounting Type: Through Hole Operating Temperature: -40°C to +80°C Weight: Approx. 8g 🔧 Applications LED Brightness Control Fan Speed Control Motor Speed Control Voltage Adjustment Current Adjustment Power Supply Circuits Arduino Projects DIY Electronics Projects Audio & Electronic Circuits Electronic Prototyping 🛠️ How It Works A potentiometer is a variable resistor with three terminals. The two outer terminals are connected to the resistive track, while the center terminal acts as the wiper. Rotating the shaft changes the wiper position and therefore changes the resistance or output voltage in the circuit. 📦 Package Includes 1 × 10KΩ Rotary Potentiometer Round Shaft Elcon ⚠️ Note Product images are shown for illustrative purposes only and may differ slightly from the actual product. The 10KΩ value and ±20% tolerance are based on the supplied product specifications.
315MHz 4 Channel Wireless RF Remote Control Kit with Receiver Module (Non-Locking Mode)
[RF Module] 📡 315MHz 4 Channel Wireless RF Remote Control Kit with Receiver Module (Non-Locking Mode) 4 Channel RF Remote • 315MHz ASK Communication • 5V Receiver • Non-Locking Mode • Long Range Wireless Control The 315MHz 4 Channel Wireless RF Remote Control Kit is a reliable wireless control solution consisting of a 4-button RF transmitter and a super regenerative ASK receiver module. Operating at 315MHz, this kit is ideal for remote switching, automation, robotics, security systems, and DIY wireless control projects. The receiver module features four independent digital outputs (D0–D3) that correspond to the four buttons on the transmitter. When a button is pressed, the respective output pin goes HIGH, returning LOW immediately after the button is released. This Non-Locking (Momentary/Jog) operation makes the module perfect for applications requiring temporary switching such as electric door control, motor jogging, relay activation, and microcontroller interfacing. The receiver operates from a 5V DC supply and features a high-sensitivity ASK receiver with a Valid Transmission (VT) output pin for reliable signal detection. The transmitter uses a fixed-code encoder for secure communication and easy operation. Ideal for Arduino, ESP32, Raspberry Pi, AVR, PIC, industrial automation, wireless switching, and educational electronics projects. ⭐ Features 4-channel wireless RF remote control kit Operating frequency: 315MHz ASK (Amplitude Shift Keying) modulation Fixed-code RF transmitter Non-Locking (Momentary/Jog) operating mode Four independent digital outputs (D0–D3) High-sensitivity super regenerative receiver 5V DC receiver operating voltage VT (Valid Transmission) status output Compact PCB design Easy interface with microcontrollers Long wireless transmission range (environment dependent) Suitable for DIY and industrial automation 📋 Technical Specifications RF Transmitter Product Type: RF Wireless Remote Control Operating Frequency: 315MHz Number of Buttons: 4 Channels: 4 Modulation: ASK (Amplitude Shift Keying) Encoding Type: Fixed Code Operating Mode: Non-Locking (Momentary) Power Supply: 12V A23 Battery (Not Included) RF Receiver Module Operating Voltage: 5V DC Operating Frequency: 315MHz Receiver Type: Super Regenerative ASK Receiver Receiver Sensitivity: -98dBm Output Channels: D0, D1, D2, D3 VT Output: Yes (Valid Signal Output) Antenna Connection: External ANT Pin Recommended Antenna Length: Approx. 17cm (Quarter-Wave) Module Dimensions: Approx. 41 × 22 × 7 mm Receiver Pin Configuration VT – Valid Signal Output D3 – Channel 4 Output D2 – Channel 3 Output D1 – Channel 2 Output D0 – Channel 1 Output +5V – Power Input GND – Ground ANT – External Antenna Connection 🔧 Operating Modes Non-Locking (Momentary/Jog Mode) Press a button → Corresponding output goes HIGH. Release the button → Output immediately returns LOW. Ideal for momentary control applications. Note: This product is supplied in Non-Locking Mode only. 🔧 Applications Suitable for: Arduino Projects ESP32 Projects Raspberry Pi Projects Wireless Relay Control Home Automation Industrial Automation Remote Door Control Electric Door Locks Wireless Switching Robotics Motor Control Lighting Control Alarm Systems Security Systems DIY Electronics Educational Projects 📦 Package Includes 1 × 4-Button 315MHz RF Wireless Remote Control 1 × 315MHz Super Regenerative Receiver Module ⚠️ Note Battery is included. A 12V A23 battery is required for operation. Avoid bending or touching the receiver's onboard inductor (copper coil), as this may affect receiver sensitivity. Wireless operating range depends on antenna quality, obstacles, and surrounding RF interference. Product appearance may vary slightly depending on the manufacturing batch.
JHD 16×2 Character LCD Display With Blue Backlight
[LED/LCD Display Module] If you want to add some visual output to your Arduino projects, you’ll need a display. If you need only a little to display, the LCD 16×2 Parallel LCD Display is a quite good solution. This is a Original JHD 16×2 Character LCD Display With Blue Backlight as there are many fake JHD Displays in the Market. This is a great blue backlight LCD display. It is fantastic for Arduino based project. This LCD 16×2 Parallel LCD Display with Blue Backlight is very easy to interface with Arduino or Other Microcontrollers. This is LCD 16×2 Parallel LCD Display that provides a simple and cost-effective solution for adding a 16×2 White on RGB Liquid Crystal Display into your project. The display is 16 character by 2 line display that has a very clear and high contrast white text upon a blue background/backlight. The values shown on the display can be either simple text or numerical values read by the sensors, such as temperature or pressure, or even the number of cycles that the Arduino is performing. For more displays click below, LED/LCD Display Features : 16 characters wide, 2 rows White text on the yellow background Single LED backlight included can be dimmed easily with a resistor or PWM. Can be fully controlled with only 6 digital lines! (Any analog/digital pins can be used) Specifications: Model： JHD659 B/W Display： 16×2 character Outline： 80.0×36.0×14.5 VA： 64.5×14.5 Controller： SPLC780D Character： 2.95×4.35 Driver： 1/16 LCD： STN Blue Negative Backlight： White LED Package Includes : 1 x JHD 16×2 Character LCD Display With Blue Backlight
MH-M18 Wireless Bluetooth Audio Receiver Board Module BLT 4.2 MP3 Lossless Decode
[Audio Receiver] MH-M18 Wireless Bluetooth Audio Receiver Board Module – Bluetooth 4.2 MP3 Lossless Decoder The MH-M18 Wireless Bluetooth Audio Receiver Module is a compact, low-power Bluetooth 4.2 audio receiver designed to add wireless audio functionality to existing speakers, amplifiers, DIY audio systems and other projects. It supports stereo two-channel audio output and lossless decoding of WAV, WMA, FLAC, APE and MP3 formats. The module can operate from 3.7–5V and provides a transmission range of up to 20 meters under suitable conditions. ⭐ Key Features Bluetooth 4.2 wireless audio receiver Converts conventional speakers/amplifiers into Bluetooth-enabled audio systems Supports stereo dual-channel audio output Supports WAV/WMA/FLAC/APE/MP3 audio decoding Bluetooth automatic connection support Maximum transmission distance up to 20 meters in open/low-interference conditions Low power consumption Can be powered from a 3.7–4.2V lithium battery or 5V supply Compact PCB suitable for DIY projects Supports Bluetooth audio protocols including HFP, A2DP and AVRCP 📋 Technical Specifications Model: MH-M18 Bluetooth Version: Bluetooth 4.2 Operating Voltage: DC 3.7–5V Maximum Operating Current: Approximately 20mA Current in Deep Sleep: Approximately 3µA Transmission Distance: Up to 20 meters Sensitivity: -87dBm Operating Temperature: -40°C to +85°C Audio Output: Stereo, dual channel Supported Formats: WAV, WMA, FLAC, APE, MP3 Bluetooth Protocols: HFP V1.7, A2DP V1.2, AVRCP V1.5, AVCTP V1.2, AVDTP V1.2 Approx. Module Size: 23 × 16mm; some listings specify approximately 23 × 16.5 × 3mm depending on version. 🔧 Applications Convert old speakers into Bluetooth speakers DIY Bluetooth speaker projects DIY audio amplifiers Portable speaker projects Home audio systems Car audio Bluetooth upgrades Wireless audio receiver projects Custom audio and electronics projects 🛠️ Basic Connection VCC: Power input GND: Ground L: Left audio output R: Right audio output Connect the L/R audio outputs to an external amplifier. This module is an audio receiver/decoder and should not be treated as a high-power speaker amplifier. 💡 Bluetooth Indicator Fast flashing: Bluetooth not connected Steady light: Bluetooth connected Slow flashing: Bluetooth audio playback in some versions ⚠️ Important Notes Do not supply more than the specified operating voltage. For lithium-battery operation, use a suitable 3.7–4.2V supply. The maximum 20m transmission distance depends on obstacles, interference and the connected Bluetooth device. This is a Bluetooth audio receiver module, not a power amplifier. Audio output should be connected to a suitable amplifier input. IC Variant Note: This product may be supplied with different compatible IC variants, including MH-M18 or JL AS208PO1429-25C4. Functionality is specified as equivalent for this product, and the variant will be shipped randomly depending on stock. 📦 Package Includes 1 × MH-M18 Wireless Bluetooth Audio Receiver Board Module
Wuzhi Audio ZK-MT21 Bluetooth 5.0 Subwoofer Amplifier Board 50WX2+100W 2.1 Channel Power Audio Stereo Amplifier Tone Board Bass AMP AUX
[Amplifier Board] Tip: Only when the audio input is sufficient and the power supply voltage/current is sufficient, there will be sufficient output power. The higher the power supply voltage, the greater the output power, and the smaller the speaker impedance, the greater the output power. Please make sure that the power of the adapter power supply is greater than the actual working power of the amplifier! You can check our others amplifier boards here. FAQ: 1. How to choose a power supply? The power supply with the board is very important. The ripple of the selected power supply must be small. A power supply with a large ripple will cause the bottom noise of the power amplifier board to become larger and there will be current noise. The higher the voltage, the greater the current, and the more adequate the output power. The power supply is 12V1A and can be equipped with 3-4inch speakers. If it is above 19V 5A, there is no problem with 8-10 inches, and the power supply must be highly regarded. If the voltage is too low, the amplified sound will easily cause sound distortion. If the current is too low, the speaker will pull down the voltage, which will result in abnormal operation or poor sound quality. It is recommended to use a power supply of 18V19V24V with a current above 5A. If you only have 9V12V or 1A 2A power supply, it can be used but the power is low. When the volume is selected close to the maximum, it may be distorted and affect the sound quality. 2. How to choose a speaker? Regarding speaker types: commonly used speakers are generally 4-8 ohms, which can be used. The left and right channel speakers need to be connected to full-range speakers or mid- to high-frequency speakers, and the power is between 20W-100W. The subwoofer speaker cannot be connected to an ordinary speaker, and a speaker with a subwoofer speaker must be connected with a power between 20-100. The dive frequency of the subwoofer speaker must be at least 50 Hz. If your speaker has a low power, such as between 20W-50W, it can be used. You need a lower power supply voltage to prevent the speaker from burning after amplifying the sound. For example, choose a power supply below 15V. If you are a 50W-100W speaker, don't worry about the problem of speaker burnout. You can choose a 12-24V power supply. The higher the selected voltage, the greater the sound or power that can be output. The speaker power should not exceed 100W, otherwise it will affect the sound quality. 3. Introduction to audio input mode This audio power amplifier module has two audio input methods: one is Bluetooth input, the other is AUX input, Bluetooth mode is preferred. Bluetooth can be connected in any mode. As long as the Bluetooth connection is successful, it is in Bluetooth mode, and the Bluetooth mode supports automatic connection back. When Bluetooth is not connected, AUX plug-in is in AUX mode. It should be note that when using AUX mode, you need to confirm that the Bluetooth connection of this module has been disconnected. 4. How to adjust the main volume? The MAIN—VOLUME knob adjusts the main volume. Right-handed main volume increases, left-handed main volume decreases. The main volume affects the volume of the left and right channels and the subwoofer. 5. How to adjust the left and right channel high and low sounds? The R&L CHANNEL—BASS knob controls the bass, right-turning bass enhancement, left-turning bass attenuation. When the knob is in the rightmost position, the bass is neither enhanced nor attenuated. The R&L CHANNEL—TREBLE knob controls the treble, the right-handed treble is enhanced, and the left-handed treble is attenuated. When the knob is in the middle position, the high pitch is neither enhanced nor attenuated. Note when adjusting the treble and bass: when the treble or bass is adjusted to the maximum by turning right, if the sound is distorted, the gain of the treble or bass adjustment is too large. You need to turn the treble or bass knob to the left to lower the gain or turn the right Turn the MAIN-VOLUME knob to the left to reduce the total volume. 6. How to adjust the subwoofer? SUBWOOFER—VOLUME knob is used to control the volume of the subwoofer. Right-handed volume increases, and left-handed volume decreases. The SUBWOOFER—FREQ knob controls the cutoff frequency of the subwoofer. The right-hand frequency increases, and the left-hand frequency decreases. The frequency adjustment range is 20HZ-200HZ. 7. The voice is small and okay. When the voice becomes louder, the voice becomes muddy? The sound is distorted, please turn down the total volume or change to a higher voltage adapter power supply. 8. The sound is small, but when the sound becomes louder, the sound freezes? If the input power is insufficient, the power supply itself is protected against intermittent power failure. Please replace it with a higher-power power supply; or if the power is too large, the power amplifier board will generate serious heat and thermal protection has occurred. Reduce power usage or enhance heat dissipation. 9. What factors are related to the sound quality? The sound quality is not only related to the power amplifier module, but also related to the power supply, sound source, and the entire audio system. Basically, every aspect of the audio system will affect the sound quality, among which the main links are the audio transmission line, the audio power supply, the tone circuit, the power amplifier circuit, the speakers and the surrounding environment. The sound quality is the best only when the sound source, power supply, amplifier module and speakers are matched. Feature: Product Name: 2.1 channel audio amplifier module Product Model: ZK-MT21 Bluetooth Version: 5.0 (no shielding, 15 meters) Input Sensitivity: 500mV Audio Input: AUX + Bluetooth Channel: 2.1 Chip Solution: Domestic power amplifier chip Power Range: DC 12-20 V / 5A above (Do not connect to 24V battery pack) Adapter Speaker: 20-100 W, 4-8 Ω Output Power: Left and right channels <50W, Subwoofer <100W Protection Mechanism: Anti reverse connection. Overheat. Overcurrent. Short circuit Product Dimensions: 93mm*90mm*22mm Package Weight : about 185g (packaging) Package Includes: 1 x ZK-MT21 bluetooth 5.0 Subwoofer Amplifier Board 50WX2+100W 2.1 Channel Power Audio Stereo Amplifier Tone Board Bass AMP AUX
Out of stock0.28 inch DC 100V 100A LED Digital Ammeter-Voltmeter With Shunt
[Ammeter and Voltmeter] This is 0.28 inch DC 100V 100A LED Digital Ammeter–Voltmeter With Shunt. This meter will measure up to 100 VDC with a 0.1-volt resolution. One thing to note is, this meter has 2 wiring harnesses. One harness is to provide power for the meters, that’s the 2 poles with a RED and a BLACK lead. Small size, portable, the magnitudes of voltage, and current are displayed on the same screen at the same time. This can be supplied anywhere from 6 volts DC up to 30 VDC. This is a separate power supply that is isolated from the source, it is possible to use the same supply but it seems to affect the amp meter reading. The 3 wire harness is used for a ground that connects directly to the battery or supply ground of the load. Note: There are different wiring variants with the same working functionality is available which will be shipped randomly. If the input voltage is more than 5V then please use the buck converter. Features : It measures up to 100V and 100A DC. Very handy and small in size. It requires a power supply of 5V. 100% Brand new and high quality. Package Includes: 1 x Dual LED Panel Ampere Voltage Meter. 1 x Current Shunt.