All products · 129 of 1440
Electronics, sensors, robotics kits, PC components, peripherals — everything Unik Systems carries, in one place.
Only 2 leftRobotic Arm Kit
DOF: 3–6 (kit dependent). Actuators: servo motors (SG90/MG90/MG996R class). Control: Arduino/servo driver (PCA9685 common). Supply: 5–6V for servos (separate recommended). Payload: light (50–200g typical for small kits).
Only 2 leftRobotic Spider Kit
Legs: 4/6/8-legged variants. Servos: 8–12 micro servos. Controller: Arduino/ESP32 compatible. Gait programming. Power: 5–6V high-current (2A–5A depending on servos). Frame: acrylic/ABS.
Out of stock0.96 Inch Blue SPI OLED Display Module 7-Pin 128×64 – SSD1306
[LED/LCD Display] 0.96 Inch Blue SPI OLED Display Module 7-Pin 128×64 – SSD1306 The 0.96-inch Blue OLED Display Module is a compact graphical display based on the SSD1306 driver IC, featuring a 128×64 pixel resolution and blue monochrome display. This version has a 7-pin interface with a dedicated CS (Chip Select) pin, making it suitable for 4-wire SPI communication. The module is factory-configured for SPI and can also be modified for I2C/IIC communication on compatible board versions. With its compact size, wide viewing angle and low-power OLED technology, it is suitable for Arduino, ESP32, ESP8266, STM32, Raspberry Pi and other microcontroller projects. ⭐ Key Features 0.96-inch blue OLED display 128 × 64 pixel resolution SSD1306 driver IC 7-pin interface Dedicated CS (Chip Select) pin Factory configured for 4-wire SPI Supports SPI and I2C/IIC with appropriate configuration 3.3V/5V compatible on supported module versions No backlight required Low power consumption Wide viewing angle of more than 160° Compact PCB design Pre-soldered 7-pin male header Compatible with Arduino, ESP32, ESP8266, STM32 and Raspberry Pi projects 📋 Technical Specifications Display Type: OLED (Organic Light-Emitting Diode) Display Colour: Blue Display Size: 0.96 inch Driver IC: SSD1306 Resolution: 128 × 64 pixels Interface: SPI / I2C Default Interface: 4-wire SPI Input Voltage: 3.3V–5V Viewing Angle: >160° Module Dimensions: Approximately 27 × 27 × 4mm Operating Temperature: Approximately -30°C to +70°C Header: 7-pin male header, pre-soldered Display Type: Monochrome blue OLED 🔌 7-Pin Interface The 7-pin version provides the following connections: GND – Ground VCC – Power supply D0 / SCK / CLK – SPI clock D1 / MOSI / SDA – SPI data RES / RST – Display reset DC / A0 – Data/Command selection CS – Chip Select 🛠️ SPI Connection The module is normally supplied in 4-wire SPI configuration. For an Arduino Uno, a typical connection is: VCC → 5V GND → GND D0 → SCK / D13 D1 → MOSI / D11 RES → Digital I/O DC → Digital I/O CS → Digital I/O The dedicated CS pin allows the OLED to share the SPI bus with other devices such as SD cards or additional SPI peripherals. 🔄 I2C / IIC Configuration On compatible versions, the module can be converted from SPI to I2C by changing the appropriate resistor configuration on the PCB. The supplied board configuration may require: Moving the resistor from R3 to R1 Shorting R8 with solder Using D0 as SCL Using D1 as SDA Configuring DC for the I2C address The exact resistor positions can vary between board revisions, so check the markings on your particular PCB before modification. 🎯 Applications Arduino projects ESP32 projects ESP8266 projects STM32 development Raspberry Pi projects IoT devices Sensor displays Voltage/current meters Battery monitors Temperature displays Digital clocks Data loggers Portable electronic devices Robotics DIY measuring instruments Embedded systems Menu and status displays 💡 Advantages of OLED OLED technology is self-emissive, meaning the pixels produce their own light and do not require a conventional backlight. This provides high contrast, compact construction and a wide viewing angle while keeping power consumption relatively low. ⚠️ Important Notes This is the 7-pin SPI version, not the 6-pin version. The module is normally configured for SPI communication. Check the PCB labels before connecting the module. Do not exceed the specified supply voltage. Although many versions support 5V operation, the exact voltage tolerance can vary between board revisions. I2C operation may require hardware resistor modification. The actual PCB layout and component markings may vary slightly between production batches. Display colour: Blue. Libraries such as Adafruit SSD1306 and U8g2 can be used with compatible microcontrollers. 📦 Package Includes 1 × 0.96 Inch Blue SPI OLED Display Module
26650 Battery Holder / Battery Spacer 2×1 – 26.3mm Bore Diameter
[Lithium Battery Holder] 26650 Battery Holder / Battery Spacer 2×1 – 26.3mm Bore Diameter The 26650 Battery Holder / Battery Spacer 2×1 is a cylindrical battery spacer designed to securely arrange 26650 lithium-ion battery cells while building multi-cell battery packs. Made from flame-retardant ABS+PC material, it provides a strong and stable structure while allowing air circulation around the cells. The holder features interlocking slots on the edges, allowing multiple spacers to be joined together to create different battery-pack sizes and configurations. After welding nickel strips, the assembled battery pack can achieve a solid and reliable structure without requiring additional connecting hardware. ⭐ Key Features Designed for 26650 cylindrical lithium-ion cells 2 × 1 configuration 26.3mm bore diameter Made from flame-retardant ABS+PC material High-temperature resistant construction Crack-resistant design Interlocking slots for connecting multiple spacers Allows flexible battery-pack configurations Provides mechanical support for battery cells Helps maintain proper spacing between cells Suitable for high-current battery-pack construction Helps improve battery-pack stability and reliability Allows airflow around the cells for heat dissipation 📋 Technical Specifications Product Type: Battery Holder / Battery Spacer Compatible Cell: 26650 cylindrical battery Configuration: 2 × 1 Number of Cells: 2 Bore Diameter: 26.3mm Material: Flame-retardant ABS+PC Construction: Interlocking modular design Mounting: Multiple spacers can be joined together Application: Lithium battery pack assembly Cell Type: Cylindrical Li-ion cells 🔧 Applications 26650 lithium-ion battery packs E-bike battery packs Electric scooter battery packs Electric vehicle battery packs Power-tool battery packs DIY high-current battery packs UPS battery systems Solar energy storage packs Portable power stations Robotics battery packs Custom lithium battery assemblies 🛠️ How to Use The spacer is designed to hold two 26650 cells in a 2×1 arrangement. Multiple spacers can be connected through the slots provided around the edges to create larger battery-pack configurations. For a complete battery pack: Cell → Spacer → Nickel Strip Welding → Additional Spacers → Battery Pack For mechanical support, spacers can be positioned at the top and bottom of the cells. Important: For each individual battery cell, 2 spacers are recommended—one at the top and one at the bottom. 💡 Advantages Simple Assembly: Easy to arrange cylindrical cells. Flexible Design: Multiple spacers can be interconnected to create different pack shapes. Strong Construction: Helps keep cells firmly positioned. Heat Dissipation: Provides spacing between cells and allows airflow. Reliable Battery Pack: Helps make the completed pack mechanically stable. Suitable for Complex Packs: Useful for custom battery configurations, including e-bike and high-current applications. ⚠️ Important Notes This product is only a battery holder/spacer; batteries are not included. The 26.3mm bore is intended for compatible 26650 cells. Check your actual cell diameter before purchase. Do not force oversized cells into the holder. Battery cells should be properly insulated and securely assembled. Use suitable nickel strip and an appropriate spot-welding method. Use a suitable BMS/protection system for the completed lithium battery pack. Battery cells should be properly matched before assembling a multi-cell pack. 2 spacers are recommended per individual cell, one on each end. Keep the battery assembly away from excessive heat, moisture and physical damage. 📦 Package Includes 1 × 26650 Battery Holder / Battery Spacer – 2×1, 26.3mm Bore Diameter Note: Battery cells, nickel strips and BMS are not included.
2S 4A Type-C Lithium Battery Charging Module – 8.4V Step-Up Boost Charger for 18650 Lipo
[Step UP Buck Converter] 2S 4A Type-C Lithium Battery Charging Module – 8.4V Step-Up Boost Charger for 18650 The 2S 4A Type-C Lithium Battery Charging Module is a compact step-up charging board designed for charging 2-cell series (2S) 18650 Li-ion/Li-Po battery packs. It accepts a 3–6V DC input through USB Type-C and boosts the voltage to 8.4V, the required full-charge voltage for a 2S lithium battery pack. The 4A specification refers to the maximum input current version. According to available product specifications, the corresponding charging current is approximately 2.2A, rather than 4A. ⭐ Key Features Designed for 2S lithium-ion/Li-Po battery packs Suitable for 2 × 18650 cells connected in series USB Type-C input 3–6V DC input Recommended input: 3.7V / 5V Step-up/boost charging circuit 8.4V charging voltage 4A maximum input-current version Approximately 2.2A charging current Automatic recharge function Battery charging protection features Compact PCB design LED charging/status indication Suitable for DIY battery and portable-power projects 📋 Technical Specifications Product Type: 2S Lithium Battery Step-Up Charging Module Battery Configuration: 2S – 2 cells in series Compatible Battery: 3.6V/3.7V Li-ion / Li-Po Nominal Battery Pack Voltage: 7.4V Full-Charge Voltage: 8.4V Input Voltage: DC 3–6V Recommended Input: DC 3.7V / 5V Maximum Input Current: 4A Charging Current: Approximately 2.2A Charging Interface: USB Type-C Charging Mode: Constant-current / constant-voltage Board Size: Approximately 39 × 18 × 6.3mm Operating Temperature: -40°C to +85°C LED Indicators: Charging / fully charged or constant-voltage status 🔋 Charging Performance For the 2S 4A version: USB Type-C 5V → Boost Charging Module → 8.4V → 2S Battery Pack The module draws up to approximately 4A from the input, while the specified charging current is approximately 2.2A. This distinction is important when selecting the USB power adapter. 🔧 Applications 2S 18650 battery packs 7.4V Li-ion battery packs 2S Li-Po battery packs DIY power banks Portable electronics Bluetooth speaker battery systems Robotics projects Solar charging applications Electronic prototyping Portable audio equipment Electric fan projects Type-C rechargeable equipment Custom battery charging systems 🛠️ How It Works The module uses a boost/step-up charging circuit to convert the lower USB Type-C input voltage into the 8.4V charging voltage required for a 2S lithium battery pack. Example: 5V Type-C Input → Step-Up Circuit → 8.4V Charging Output → 2S 18650 Battery A 2S battery pack consists of two lithium cells connected in series: 3.7V + 3.7V = 7.4V nominal4.2V + 4.2V = 8.4V fully charged 💡 LED Indicators The module uses status indicators to show the charging condition: CR: Charging OK: Fully charged / constant-voltage stage ⚠️ Important Notes This module is intended for 2S battery packs only. Do not connect a single 18650 cell directly to the 8.4V charging output. The two cells should be properly matched and in good condition. Do not exceed the 6V maximum input voltage. A suitable Type-C power source is required to supply the necessary input current. The 4A rating is the input-current rating, not the battery charging current. The specified charging current for this 2S 4A version is approximately 2.2A. This charging module should not automatically be considered a replacement for a dedicated 2S BMS/protection board. Use appropriate battery protection where required. Check the PCB polarity and connection markings before connecting the battery. Do not short-circuit the input or output. Use properly matched lithium cells for safe and reliable charging. Keep the module adequately ventilated during higher-current operation. 📦 Package Includes 1 × 2S 4A Type-C Step-Up Boost Lithium Battery Charging Module – 8.4V
2.25-Inch 8ohms 8W Full Range Speaker for Compact Audio Applications
[Speakers] 2.25-Inch 8Ω 8W Full Range Speaker for Compact Audio Applications The 2.25-Inch 8Ω 8W Full Range Speaker is a compact and efficient audio driver designed for small electronic and embedded sound applications. Featuring an 8Ω impedance and 8W power rating, this speaker delivers clear and balanced sound output while maintaining low power consumption and excellent efficiency. Its compact size makes it ideal for projects where installation space is limited, including portable speakers, DIY electronics, toys, alarm systems, intercom devices, and mini speaker enclosures. The full-range design allows it to reproduce a broad range of audio frequencies, making it suitable for both voice and music playback applications. Built with durable materials and designed for reliable long-term performance, this speaker is an excellent choice for electronics hobbyists, engineers, and product developers working on custom audio projects. ⭐ Key Features 2.25-Inch compact speaker driver 8Ω impedance 8W power rating Full-range audio reproduction Clear and balanced sound output Lightweight and compact design Easy to mount in enclosures and panels Suitable for low to medium-power audio applications Durable construction for long-term use Ideal for DIY and embedded audio systems 📋 Technical Specifications Product Type: Full Range Speaker Speaker Size: 2.25 Inch Impedance: 8Ω Power Rating: 8W Speaker Type: Full Range Mounting Type: Enclosure / Panel Mount Application Type: Audio Output 🔧 Applications Portable Speaker Systems DIY Audio Projects Bluetooth Speaker Modules Toys and Educational Kits Alarm and Notification Systems Embedded Electronic Devices Mini Amplifiers and Sound Modules Intercom Systems Robotics Projects Custom Speaker Enclosures ⚠️ Precautions Do not exceed the 8W rated power. Use an amplifier compatible with an 8Ω speaker load. Avoid exposure to moisture and excessive dust. Mount securely to minimize vibration and distortion. Do not apply direct pressure on the speaker cone. 📦 Package Includes 1 × 2.25-Inch 8Ω 8W Full Range Speaker
57mm (2.25-Inch) Internal Magnet Speaker 4Ohms 3W Full Range Audio Speaker
[Speakers] 57mm (2.25-Inch) Internal Magnet Speaker – 4Ω 3W Full Range Audio Speaker The 57mm (2.25-Inch) Internal Magnet Speaker is a compact and reliable full-range audio speaker designed for DIY electronics, multimedia devices, embedded sound systems, and portable audio applications. Featuring a 4Ω impedance and 3W power rating, this speaker delivers clear and balanced sound output while maintaining a slim and lightweight design. Its internal magnet structure provides a compact profile, making it ideal for applications where installation space is limited. The durable mounting frame allows easy integration into speaker enclosures, control panels, intercom systems, audio modules, and custom electronic projects. Designed for consistent audio performance, this speaker is suitable for voice playback, music, alerts, and general audio output in both portable and embedded electronic devices. ⭐ Key Features 57mm (2.25-Inch) compact speaker 4Ω impedance 3W power rating Internal magnet design Full-range audio reproduction Built-in mounting frame Clear and balanced sound output Compact and lightweight construction Easy installation in custom enclosures Suitable for portable and embedded audio applications Ideal for DIY electronics and speaker projects 📋 Technical Specifications Product Type: Internal Magnet Speaker Speaker Size: 57mm (2.25 Inch) Impedance: 4Ω Power Rating: 3W Speaker Type: Full Range Magnet Type: Internal Magnet Frame Type: With Mounting Frame Mounting: Frame / Panel Mount Application: Embedded Audio Systems 🔧 Applications DIY Electronics Projects Audio Modules & Music Players Intercom and Communication Systems Toys and Educational Devices Portable Audio Systems Alarm and Notification Devices Embedded Audio Applications Mini Speaker Enclosures Multimedia Devices Robotics and Automation Projects ⚠️ Precautions Do not exceed the 3W rated power. Use an amplifier compatible with a 4Ω speaker load. Ensure proper wiring polarity during installation. Avoid exposure to moisture and dust. Mount securely to reduce vibration noise. Do not apply direct pressure on the speaker cone. 📦 Package Includes 1 × 57mm (2.25-Inch) 4Ω 3W Internal Magnet Full Range Speaker
45mm (1.75-Inch) Internal Magnet Speaker 2 Ohms 10W Full Range Audio Speaker
[Speakers] 45mm (1.75-Inch) Internal Magnet Speaker – 2Ω 10W Full Range Audio Speaker The 45mm (1.75-Inch) Internal Magnet Speaker is a compact and powerful audio driver designed for DIY electronics, portable speakers, multimedia devices, toys, embedded audio systems, and custom speaker enclosures. Featuring a 2Ω impedance and 10W power rating, this speaker provides strong audio output when paired with a compatible amplifier. Its internal magnet design provides a compact profile while maintaining efficient magnetic performance. The built-in mounting frame makes installation easy in custom enclosures and electronic devices. With its 2Ω low-impedance configuration, this speaker is suitable for compatible Class-D amplifier modules where higher output power is required from a compact speaker driver. ⭐ Key Features 45mm (1.75-Inch) compact speaker 2Ω impedance 10W power rating Internal magnet design Full-range audio reproduction Compact and lightweight construction Built-in mounting frame Clear and powerful sound output Easy to install in custom enclosures Suitable for portable and embedded audio applications Ideal for DIY speaker projects 📋 Technical Specifications Product Type: Internal Magnet Speaker Speaker Size: 45mm (1.75 Inch) Impedance: 2Ω Power Rating: 10W Speaker Type: Full Range Magnet Type: Internal Magnet Frame Type: Mounting Frame Mounting: Frame / Panel Mount Application: Embedded & Portable Audio 🔧 Applications DIY Bluetooth Speaker Projects Portable Speaker Systems Mini Audio Amplifiers Multimedia Devices Toys and Educational Kits Intercom Systems Alarm and Notification Systems Embedded Audio Devices Custom Speaker Enclosures Robotics Projects Electronic Projects ⚠️ Precautions Use an amplifier that supports a 2Ω load. Do not exceed the 10W rated power. Check amplifier output impedance before connecting. Observe correct speaker polarity during installation. Avoid excessive mechanical pressure on the speaker cone. Keep away from moisture and excessive dust. Mount securely to minimize unwanted vibration and distortion. 📦 Package Includes 1 × 45mm (1.75-Inch) 2Ω 10W Internal Magnet Full Range Speaker
2.25 Inch 4 Ohm 10 Watt Full Range Speaker with Neodymium Magnet
[Speakers] 2.25-Inch Speaker Driver • 4 Ohm Impedance • 10W Power Rating • Neodymium Magnet • Compact Full Range Audio Speaker The 2.25 Inch 4 Ohm 10 Watt Full Range Speaker with Neodymium Magnet is a compact and high-performance speaker driver designed for portable audio systems, DIY speaker projects, multimedia devices, embedded electronics, and custom sound enclosures. Featuring a powerful neodymium magnet, this speaker delivers clear vocals, balanced midrange, and improved bass response while maintaining a lightweight and compact design. With a 4 ohm impedance and 10 watt power rating, the speaker is suitable for use with small audio amplifiers, Bluetooth amplifier modules, DIY portable speakers, mini sound systems, toys, alarm systems, educational kits, and embedded electronic devices. The full-range design allows it to reproduce a wide spectrum of audio frequencies without requiring additional tweeters for many compact applications. Its durable construction and lightweight neodymium magnet assembly make it ideal for applications where both performance and space efficiency are important. ⭐ Features Compact 2.25-inch full range speaker Powerful neodymium magnet 4 ohm impedance 10 watt power rating Clear and balanced sound output Enhanced vocal clarity and midrange performance Lightweight and compact construction Easy to mount in custom enclosures Suitable for portable and embedded audio systems Ideal for DIY electronics and audio projects 📋 Technical Specifications Product Type: Full Range Speaker Driver Speaker Size: 2.25 Inch Impedance: 4 Ohm Power Rating: 10 Watt Magnet Type: Neodymium Speaker Type: Full Range Mounting Type: Enclosure / Panel Mount Application Type: Audio Output Frame Material: Metal Cone Material: Paper Composite Color: Black 🔧 Applications Suitable for: Portable Speaker Systems Bluetooth Speakers DIY Audio Projects Mini Sound Systems Multimedia Devices Toys and Educational Kits Alarm and Notification Systems Embedded Electronic Devices Mini Amplifiers Sound Modules Intercom Systems Custom Speaker Enclosures Robotics and Electronics Projects 📦 Package Includes 1 × 2.25 Inch 4 Ohm 10 Watt Full Range Speaker with Neodymium Magnet ⚠️ Precautions Do not exceed the 10W rated power. Use an amplifier compatible with 4 ohm speakers. Avoid exposure to moisture, water, and excessive dust. Mount the speaker securely to minimize unwanted vibration. Do not apply direct pressure to the speaker cone or surround.
802580 LiPo Battery 700mAh 3.7V High Discharge 25c for Drone
[LiPo Cell] LiPo Battery 700mAh 3.7V High Discharge 802580 3.7V Lithium Polymer Battery • 700mAh Capacity • 25C High Discharge • 802580 Cell • Molex 2.0mm 2-Pin Connector The LiPo Battery 700mAh 3.7V High Discharge 802580 is a compact and lightweight Lithium Polymer (LiPo) rechargeable battery designed for applications that require high current output in a small form factor. Built with high-quality lithium polymer cells, this battery delivers a nominal voltage of 3.7V and a 700mAh capacity, making it ideal for RC toys, drones, mini helicopters, robotics, wireless electronics, and DIY projects. With a 25C continuous discharge rating, this battery can provide rapid bursts of current for motors and other high-power devices. The battery comes with a Molex 2.0mm 2-pin connector and an integrated protection PCB, offering added safety during charging and discharging. The 802580 cell size refers to the approximate dimensions of 8.0 × 25 × 80 mm, allowing the battery to fit easily into compact electronic devices while maintaining excellent power-to-weight performance. Note: This battery is intended for high-discharge applications such as RC models and robotics. It is not recommended for long-duration low-current devices such as cameras or data loggers. ⭐ Features High-quality 3.7V 700mAh LiPo battery 25C continuous discharge capability Compact 802580 cell size Lightweight design Stable voltage output Built-in protection circuit (PCB) Pre-installed Molex 2.0mm 2-pin connector Excellent power-to-weight ratio Rechargeable and reusable Suitable for high-current applications Easy plug-and-play installation 📋 Technical Specifications Product Type: Rechargeable Lithium Polymer (LiPo) Battery Battery Chemistry: Lithium Polymer (Li-ion Polymer) Cell Size: 802580 Nominal Voltage: 3.7V Full Charge Voltage: 4.20V Typical Capacity: 700mAh Discharge Rating: 25C Continuous Dimensions: Approx. 8.0 × 25 × 80 mm Weight: Approx. 18g Connector Type: Molex 2.0mm 2-Pin Protection Circuit: Built-in PCB Protection Rechargeable: Yes 🔧 Applications Suitable for: RC Cars RC Airplanes RC Helicopters Drones & Quadcopters Robotics Projects Arduino Projects ESP32 Projects DIY Electronics Portable Devices Wireless Modules Educational Projects Electronic Prototyping Battery Replacement Projects Miniature Electronics 📦 Package Includes 1 × LiPo Battery 700mAh 3.7V High Discharge 802580 with Molex 2.0mm 2-Pin Connector ⚠️ Safety Instructions Use only LiPo-compatible chargers. Do not charge above 4.20V. Do not discharge below the recommended cut-off voltage. Do not short-circuit the battery terminals. Do not puncture, crush, or expose the battery to fire. Store partially charged in a cool, dry place when not in use. Ensure connector polarity matches your device before connection.
702035 LiPo Battery 400mAh 3.7V High Discharge 25C For Drone
[LiPo Cell] LiPo Battery 400mAh 3.7V High Discharge 702035 3.7V Lithium Polymer Battery • 400mAh Capacity • 25C High Discharge • 702035 Cell • Molex 2.0mm 2-Pin Connector The LiPo Battery 400mAh 3.7V High Discharge 702035 is a compact and lightweight Lithium Polymer (LiPo) rechargeable battery designed for applications that require high current output in a small form factor. Built with high-quality lithium polymer cells, this battery delivers a nominal voltage of 3.7V and a 400mAh capacity, making it ideal for RC toys, drones, mini helicopters, robotics, wireless electronics, and DIY projects. With a 25C continuous discharge rating, this battery can provide rapid bursts of current for motors and other high-power devices. The battery comes with a Molex 2.0mm 2-pin connector and an integrated protection PCB, offering added safety during charging and discharging. The 702035 cell size refers to the approximate dimensions of 7.0 × 20 × 35 mm, allowing the battery to fit easily into compact electronic devices while maintaining excellent power-to-weight performance. Note: This battery is intended for high-discharge applications such as RC models and robotics. It is not recommended for long-duration low-current devices such as cameras or data loggers. ⭐ Features High-quality 3.7V 400mAh LiPo battery 25C continuous discharge capability Compact 702035 cell size Lightweight design Stable voltage output Built-in protection circuit (PCB) Pre-installed Molex 2.0mm 2-pin connector Excellent power-to-weight ratio Rechargeable and reusable Suitable for high-current applications Easy plug-and-play installation 📋 Technical Specifications Product Type: Rechargeable Lithium Polymer (LiPo) Battery Battery Chemistry: Lithium Polymer (Li-ion Polymer) Cell Size: 702035 Nominal Voltage: 3.7V Full Charge Voltage: 4.20V Typical Capacity: 400mAh Discharge Rating: 25C Continuous Dimensions: Approx. 7.0 × 20 × 35 mm Weight: Approx. 12g Connector Type: Molex 2.0mm 2-Pin Protection Circuit: Built-in PCB Protection Rechargeable: Yes 🔧 Applications Suitable for: RC Cars RC Airplanes RC Helicopters Drones & Quadcopters Robotics Projects Arduino Projects ESP32 Projects DIY Electronics Portable Devices Wireless Modules Educational Projects Electronic Prototyping Battery Replacement Projects Miniature Electronics 📦 Package Includes 1 × LiPo Battery 400mAh 3.7V High Discharge 702035 with Molex 2.0mm 2-Pin Connector
107 × 61mm 5V 180mA Mini Solar Panel Cell Module
[Solar Panel] ☀️ 107 × 61mm 5V 180mA Mini Solar Panel Cell Module (0.9W) 5V Output • 180mA Current • Polycrystalline Solar Cell • Compact & Lightweight • DIY Solar Projects The 107 × 61mm Mini Solar Panel Cell Module is a compact and efficient photovoltaic module designed to convert sunlight into clean and renewable electrical energy. Delivering a stable 5V output with a maximum current of 180mA, this solar panel is ideal for powering small electronic devices, battery charging circuits, educational projects, and DIY solar applications. Built using high-quality polycrystalline silicon solar cells, the panel provides efficient energy conversion with reliable performance under direct sunlight. Its compact size and lightweight construction make it easy to integrate into portable electronics, robotics, IoT devices, and renewable energy projects. Designed with a durable, weather-resistant construction, the module is suitable for both indoor demonstrations and outdoor applications. Pre-drilled mounting holes allow quick installation on enclosures, backpacks, models, and custom solar-powered devices. ⭐ Features High-efficiency polycrystalline solar panel Stable 5V DC output Maximum output current of 180mA Maximum power output of 0.9W Compact and lightweight design Efficient solar energy conversion Weather-resistant construction Pre-drilled mounting holes Easy integration into DIY projects Eco-friendly renewable energy source Maintenance-free operation Suitable for educational and hobby applications 📋 Technical Specifications Product Type: Mini Solar Panel Cell Module Panel Dimensions: 107 × 61 mm Cell Type: Polycrystalline Silicon Maximum Power Output: 0.9W Output Voltage: 5V DC Maximum Output Current: 180mA Conversion Efficiency: Approx. 17% Operating Temperature: -40°C to +85°C Storage Temperature: -40°C to +85°C Construction: Waterproof, Weather-Resistant Mounting: Pre-Drilled Mounting Holes Material: High-Quality Polycrystalline Silicon Weight: Approx. 16g 🔧 Applications Suitable for: DIY Solar Projects Solar Battery Chargers Mobile Charging Projects Arduino Projects ESP32 Projects Raspberry Pi Accessories Robotics IoT Devices Solar Garden Lights Educational Science Experiments Portable Electronics Renewable Energy Demonstrations Emergency Backup Projects Small DC Power Applications 📦 Package Includes 1 × 107 × 61mm 5V 180mA Mini Solar Panel Cell Module ⚠️ Note Output voltage and current depend on sunlight intensity, panel angle, and environmental conditions. For battery charging applications, use a suitable charge controller or charging module. Designed for low-power electronic projects and educational use. Product appearance and dimensions may vary slightly depending on the manufacturing batch.
3-in-1 Aluminum Heat Sink Set for Raspberry Pi 3
[Aluminium Heat Sink] ❄️ 3-in-1 Aluminum Heat Sink Set for Raspberry Pi 3 High-Quality Aluminum • Self-Adhesive Thermal Tape • Improved Cooling • Easy Installation The 3-in-1 Aluminum Heat Sink Set for Raspberry Pi 3 is a premium cooling accessory designed to improve heat dissipation and maintain stable operating temperatures for Raspberry Pi boards. Manufactured from high-quality aluminum, these heat sinks efficiently transfer heat away from critical components, helping improve performance and extend the life of your Raspberry Pi. The kit includes three aluminum heat sinks of different sizes to cool the processor, Ethernet/LAN controller, and other heat-generating ICs. Each heat sink comes pre-installed with a high-performance thermal adhesive backing, allowing quick and secure installation without the need for additional thermal paste or glue. By reducing operating temperatures, the heat sinks help prevent thermal throttling during continuous operation, making them ideal for overclocking, media centers, home servers, IoT applications, industrial automation, and embedded systems. ⭐ Features Premium-quality aluminum construction Excellent thermal conductivity Self-adhesive thermal tape for easy installation No thermal paste required Lightweight and durable Improves heat dissipation Reduces processor temperature Helps prevent thermal throttling Ideal for continuous operation and overclocking Designed specifically for Raspberry Pi boards Corrosion-resistant aluminum finish Easy peel-and-stick installation 📋 Technical Specifications Product Type: Aluminum Heat Sink Set Compatibility: Raspberry Pi 3 Model A, A+, B, B+ Material: Aluminum Color: Silver Quantity: 3 Heat Sinks Mounting Method: Self-Adhesive Thermal Tape Thermal Interface: Pre-applied Thermal Adhesive Cooling Type: Passive Cooling Weight: Lightweight Installation: Peel-and-Stick 🔧 Applications Suitable for: Raspberry Pi 3 Model B Raspberry Pi 3 Model B+ Raspberry Pi 3 Model A+ Raspberry Pi 3 Model A Raspberry Pi Media Center Home Automation Projects IoT Devices Embedded Systems Robotics Projects Industrial Controllers NAS Servers Retro Gaming Consoles AI Edge Computing Educational Projects DIY Electronics 📦 Package Includes 1 × Large Aluminum Heat Sink (CPU) 1 × Medium Aluminum Heat Sink (LAN/Ethernet Controller) 1 × Small Aluminum Heat Sink (Additional IC / Spare)
110 × 69mm 5V 180mA Mini Solar Panel Cell Module
[Solar Panel] ☀️ 110 × 69mm 5V 180mA Mini Solar Panel Cell Module (0.9W) 5V Output • 180mA Current • 0.9W Power • Polycrystalline Solar Cell • Compact & Lightweight The 110 × 69mm 5V 180mA Mini Solar Panel Cell Module is a compact and efficient photovoltaic module designed to convert sunlight into clean, renewable electrical energy. Delivering a stable 5V output with a maximum current of 180mA, this solar panel is ideal for powering low-power electronic devices, DIY solar projects, battery charging applications, and educational experiments. Built using high-quality polycrystalline silicon solar cells, the module offers efficient energy conversion while maintaining reliable performance under sunlight. Its lightweight construction and compact dimensions make it easy to integrate into portable devices, robotics projects, solar-powered gadgets, and outdoor applications. Designed for durability, the panel features a weather-resistant construction suitable for outdoor use. With pre-drilled mounting holes, installation is quick and convenient for a wide range of renewable energy projects. ⭐ Features High-efficiency polycrystalline solar panel Stable 5V DC output Maximum output current of 180mA Maximum power output of 0.9W Compact size for portable projects Lightweight and easy to install Weather-resistant construction Pre-drilled mounting holes Suitable for outdoor applications Eco-friendly renewable energy source No external power source required Ideal for educational and DIY projects 📋 Technical Specifications Product Type: Mini Solar Panel Cell Module Cell Type: Polycrystalline Silicon Maximum Power Output: 0.9W Output Voltage: 5V DC Maximum Output Current: 180mA Panel Dimensions: 110 × 69 mm Operating Temperature: -40°C to +85°C Storage Temperature: -40°C to +85°C Construction: Weather-Resistant Connector: None (Solder Wire Connection) Weight: Approximately 15g 🔧 Applications Suitable for: DIY Solar Projects Solar Battery Chargers Mobile Phone Charging Projects Arduino Projects ESP32 & ESP8266 Projects Raspberry Pi Accessories Robotics Projects Solar Garden Lights Educational Science Experiments IoT Devices Portable Electronic Devices Renewable Energy Demonstrations Emergency Backup Power Projects Small DC Loads 📦 Package Includes 1 × 110 × 69mm 5V 180mA Mini Solar Panel Cell Module ⚠️ Note Output voltage and current depend on sunlight intensity and panel orientation. For battery charging applications, use a suitable solar charge controller or charging module. This panel is intended for low-power applications and may not provide sufficient power under low-light conditions. Product appearance may vary slightly depending on the manufacturing batch.
XH-M401 DC-DC Step Down Buck Converter Power Supply Module XL4016E1
[Step Down Buck Converter] ⚡ XL4016 12A DC-DC Step-Down Buck Converter Module Adjustable Power Supply 12A High Current • Adjustable Output • Up to 96% Efficiency • Ideal for Battery Charging & Power Supply Applications The XL4016 DC-DC Step-Down Buck Converter Module is a high-performance switching voltage regulator designed to efficiently convert higher DC input voltages into a stable, adjustable lower output voltage. Based on the XL4016 PWM Buck Converter IC, this module supports input voltages from 8V to 36V DC and provides an adjustable output voltage from 1.25V to 32V, making it suitable for a wide range of power supply applications. Capable of delivering up to 12A output current with conversion efficiencies of up to 96%, the module features built-in thermal shutdown, current limiting, and short-circuit protection for safe and reliable operation. Its compact design and excellent voltage regulation make it ideal for powering electronic projects, battery charging systems, LED lighting, industrial equipment, communication devices, and laboratory power supplies. ⭐ Features Based on the XL4016 high-performance buck converter IC Wide input voltage range of 8V–36V DC Adjustable output voltage from 1.25V–32V DC Supports output current up to 12A High conversion efficiency up to 96% Built-in thermal shutdown protection Built-in over-current protection Built-in output short-circuit protection Excellent line and load regulation Compact PCB design Suitable for battery charging and DC power applications 📋 Technical Specifications Product Type: DC-DC Buck Converter Module Model: XL4016 (XH-M401 / HW-439 / HW-674) Converter Type: Step-Down (Buck) Input Voltage: 8V–36V DC Output Voltage: 1.25V–32V DC (Adjustable) Maximum Output Current: 12A Maximum Conversion Efficiency: Up to 96% Load Regulation: ±0.5% Voltage Regulation: ±0.5% Switching Frequency: 180kHz Protection Features: Over-Current Protection Thermal Shutdown Protection Output Short-Circuit Protection PCB Size: 60 × 40 mm Operating Principle: PWM Step-Down Regulation 🔧 Applications Suitable for: Adjustable DC Power Supplies Lithium Battery Charging Lead Acid Battery Charging Solar Power Systems LED Drivers LCD Monitors LCD Televisions Portable Instruments Telecommunication Equipment Networking Equipment Robotics Projects Arduino Projects ESP32 Projects Industrial Automation DIY Electronics 📦 Package Includes 1 × XL4016 12A DC-DC Step-Down Buck Converter Module ⚠️ Note This is a step-down (buck) converter; the input voltage must always be higher than the required output voltage. Adjust the output voltage before connecting sensitive electronic devices. Product may be supplied as XH-M401, HW-439, or HW-674, depending on stock availability. All variants offer equivalent functionality.
Blivex LFP32700 3.2V 6Ah LiFePO₄ Rechargeable Battery Cell
[LiFePO4 Battery Cell] 🔋 Blivex LFP32700 3.2V 6Ah LiFePO₄ Rechargeable Battery Cell High Capacity • Long Cycle Life • High Discharge Performance • Ideal for Energy Storage & Electric Vehicles The Blivex LFP32700 3.2V 6Ah LiFePO₄ Rechargeable Cell is a premium cylindrical lithium iron phosphate (LiFePO₄) battery designed for high-performance energy storage and power applications. Featuring a nominal voltage of 3.2V, 6Ah capacity, and up to 18A continuous discharge current, this cell delivers stable output voltage, excellent safety, and long service life. The specification identifies the product as a LFP32700-6.0Ah LiFePO₄ cylindrical rechargeable cell. Manufactured with a robust steel enclosure, the battery offers excellent resistance to vibration, shock, and harsh operating conditions while maintaining low self-discharge and high energy efficiency. It is suitable for battery packs used in electric vehicles, solar energy storage systems, portable power stations, communication backup systems, robotics, and industrial equipment. The datasheet also highlights its sturdy steel case, high capacity, long cycle life, stable output voltage, and good high/low temperature performance. Datasheet : Click Here To Open ⭐ Features High-capacity 6Ah LiFePO₄ cylindrical cell Nominal voltage of 3.2V Excellent cycle life of 2000+ cycles High continuous discharge capability up to 18A (3C) Peak pulse discharge current up to 30A (5C) Low internal resistance (≤8mΩ) Stable output voltage Low self-discharge High safety and thermal stability Sturdy pressure-resistant steel casing Excellent vibration and shock resistance Suitable for battery pack assembly 📋 Technical Specifications Brand: Blivex Model: LFP32700-6.0Ah Battery Chemistry: Lithium Iron Phosphate (LiFePO₄) Battery Type: Cylindrical Rechargeable Cell Nominal Voltage: 3.2V Nominal Capacity: 6.0Ah Energy Density: 142Wh/kg Internal Resistance: ≤8mΩ (AC, 1000Hz) Limited Charge Voltage: 3.65V Charge Method: CC/CV Standard Charge Current: 0.5C Maximum Charge Current: 1C Charge Cut-off Current: 0.3A Discharge Cut-off Voltage: 2.0V Standard Discharge Current: 6A (1C) Maximum Continuous Discharge Current: 18A (3C) Maximum Pulse Discharge Current: 30A (10 seconds) Cycle Life: 1500 Cycles (25°C, 100% DOD) Charge Temperature: 0°C to 60°C Recommended Charge Temperature: 15°C to 40°C Discharge Temperature: -30°C to 60°C Recommended Discharge Temperature: 15°C to 40°C Cell Diameter: 32.2 ± 0.3mm Cell Height: 70.5 ± 0.3mm Weight: 135 ± 5g These specifications are taken from the manufacturer's datasheet. 🔧 Applications Suitable for: Solar Energy Storage Systems Portable Power Stations Home Energy Storage UPS Backup Systems Electric Scooters Electric Tricycles Electric Four-Wheel Vehicles Electric Logistics Vehicles Battery Pack Manufacturing Communication Backup Power Industrial Energy Storage Robotics Projects DIY LiFePO₄ Battery Packs Marine & RV Power Systems The manufacturer lists applications including electric two-wheel vehicles, tricycles, logistics vehicles, special vehicles, portable energy storage, household energy storage, industrial energy storage, and communication backup power. 📦 Package Includes 1 × Blivex LFP32700 3.2V 6Ah LiFePO₄ Rechargeable Battery Cell ⚠️ Note Use only with a compatible LiFePO₄ charger and an appropriate Battery Management System (BMS). Do not short-circuit, crush, puncture, disassemble, or expose the battery to fire or excessive heat. Store the battery in a cool, dry place when not in use. Product appearance may vary slightly depending on the manufacturing batch. The datasheet includes additional handling, storage, and safety precautions for transportation, storage, and battery use.
ESP32-C3 Super Mini Development Board With Headers Pins
[ESP Modules] Ultra Compact • Wi-Fi & BLE 5.0 • USB Type-C • Perfect for IoT & Embedded Projects The ESP32-C3 Super Mini Development Board is a compact, feature-rich development board built around the powerful ESP32-C3 SoC from Espressif. Powered by a 32-bit RISC-V single-core processor running at up to 160MHz, it combines 2.4GHz Wi-Fi, Bluetooth 5.0 Low Energy (BLE), and low-power operation in an ultra-small form factor. Designed for IoT, smart home, wireless communication, automation, and embedded system development, the ESP32-C3 Super Mini offers 4MB Flash memory, 400KB SRAM, multiple GPIOs, ADC, PWM, UART, SPI, and I2C interfaces for connecting sensors, displays, relays, and other peripherals. The onboard USB Type-C interface simplifies programming and power supply, while the built-in USB-to-Serial functionality enables quick firmware uploading without requiring additional programmers. Fully compatible with Arduino IDE, ESP-IDF, PlatformIO, and MicroPython, it is suitable for beginners, students, makers, and professional developers. Its ultra-compact breadboard-friendly design makes it ideal for portable and space-constrained projects where performance, wireless connectivity, and energy efficiency are essential. Note: Programming, software configuration, driver installation, firmware flashing, and coding-related issues are not covered under return or replacement. Users are expected to troubleshoot software-related issues independently. ⭐ Features Powerful ESP32-C3 32-bit RISC-V processor CPU frequency up to 160MHz Built-in 2.4GHz Wi-Fi (802.11 b/g/n) Integrated Bluetooth 5.0 Low Energy (BLE) Ultra-compact Super Mini design Breadboard-friendly layout USB Type-C interface for programming and power 4MB onboard Flash memory 400KB SRAM Multiple GPIO, ADC, PWM, UART, SPI & I2C interfaces Low power consumption with Deep Sleep mode Onboard programmable LED Compatible with Arduino IDE, ESP-IDF, PlatformIO & MicroPython Ideal for IoT, automation, robotics, and wireless applications 📋 Technical Specifications Product Type: Development Board Board Model: ESP32-C3 Super Mini Microcontroller: ESP32-C3 Processor Architecture: 32-bit RISC-V CPU Frequency: Up to 160MHz Core: Single Core Flash Memory: 4MB SRAM: 400KB Wi-Fi Standard: IEEE 802.11 b/g/n (2.4GHz) Bluetooth: Bluetooth 5.0 Low Energy (BLE) Operating Voltage: 3.3V Input Voltage: 5V via USB Type-C or 3.3V External USB Interface: USB Type-C GPIO: Multiple Digital GPIO Pins Analog Input: Up to 6 ADC Channels PWM: Supported UART: Supported SPI: Supported I2C: Supported USB-to-Serial: Onboard Onboard LED: User Programmable (GPIO8) Power Consumption: Ultra Low (Deep Sleep ≈ 43µA) Dimensions: Approx. 22.5 × 18 mm Headers: Pre-Soldered 🔧 Applications Suitable for: Internet of Things (IoT) Smart Home Automation Wireless Sensor Networks Home Automation Systems Bluetooth Low Energy Devices Wi-Fi Enabled Controllers Robotics Projects Data Logging Systems Remote Monitoring Industrial Automation Portable Embedded Devices Educational Learning DIY Electronics Projects Wearable Electronics Rapid Prototyping 📦 Package Includes 1 × ESP32-C3 Super Mini Development Board Pin Headers ⚠️ Note Programming, firmware installation, software configuration, and driver-related issues are not covered under warranty, return, or replacement. Please verify board compatibility and install the appropriate development environment before programming. Soldered and non-soldered header pin depend on stock
Winway 18650 Lithium-Ion Rechargeable Battery 3.7V 2600mAh 9.62Wh
[Lithium Battery Cell] The Winway 18650 Lithium-Ion Rechargeable Battery is a high-performance cylindrical Li-ion cell designed to deliver reliable and long-lasting power for a wide range of electronic devices. With a nominal voltage of 3.7V, 2600mAh capacity, and 9.62Wh energy rating, it provides consistent power output for both high-drain and low-drain applications. Manufactured using premium lithium-ion cell technology, this battery offers excellent energy density, stable discharge performance, and long cycle life. Its standard 18650 form factor makes it compatible with most battery holders, chargers, and devices designed for 18650 cells. The Winway 2600mAh battery is widely used in rechargeable flashlights, emergency lights, battery packs, power banks, Bluetooth speakers, portable fans, solar lighting, DIY electronics, robotics, and various battery-operated devices. Designed for durability and dependable performance, this battery delivers excellent backup time while maintaining stable voltage throughout the discharge cycle. ⭐ Features High-quality 18650 Lithium-Ion rechargeable battery 2600mAh high-capacity cell Nominal voltage of 3.7V Energy rating of 9.62Wh Stable discharge performance High energy density Long charge and discharge cycle life Lightweight and compact cylindrical design Suitable for battery pack assembly Compatible with standard 18650 battery holders and chargers 📋 Technical Specifications Product Type: Lithium-Ion Rechargeable Battery Brand: Winway Battery Model: 18650 Nominal Voltage: 3.7V Nominal Capacity: 2600mAh Energy: 9.62Wh Battery Chemistry: Lithium-Ion (Li-ion) Cell Type: Rechargeable Form Factor: Cylindrical 18650 Diameter: Approx. 18mm Length: Approx. 65mm Weight: Approx. 45g Color: Green Rechargeable: Yes Made In: India Pack Quantity: 1 Piece 🔧 Applications Suitable for: Rechargeable Flashlights Emergency Lights Power Banks Bluetooth Speakers Portable Fans Solar Lighting Systems DIY Battery Packs Robotics Projects Arduino Projects ESP32 Projects Electronic Toys Portable Electronic Devices Medical Equipment (Compatible Models) Industrial Electronic Equipment 📦 Package Includes 1 × Winway 18650 Lithium-Ion Rechargeable Battery 3.7V 2600mAh ⚠️ Safety Instructions Use only a compatible Li-ion battery charger. Do not short-circuit, puncture, crush, or disassemble the battery. Do not expose the battery to fire, excessive heat, or water. Observe correct polarity during installation. Do not overcharge or over-discharge the battery. Store in a cool, dry place away from direct sunlight.
3.7V 700mAh 503035 Rechargeable Lithium Polymer (Li-Po) Battery for DIY Electronics, Robotics
[LiPo Cell] The 503035 3.7V 700mAh Rechargeable Lithium Polymer Battery is a compact and reliable power source designed for portable electronic devices and embedded applications. Manufactured using advanced Lithium Polymer (Li-Po) technology, it provides high energy density, lightweight construction, and excellent charge/discharge performance. In addition, the battery delivers a nominal voltage of 3.7V and a capacity of 700mAh, making it suitable for devices that require compact size with extended runtime. As a result, it is widely used in Bluetooth speakers, wireless headphones, GPS trackers, drones, robotics, IoT devices, portable medical equipment, and DIY electronics projects. Because of its slim profile, the battery can be easily integrated into compact electronic enclosures where space is limited. Furthermore, its low self-discharge rate and long cycle life ensure dependable performance over repeated charging cycles. The battery comes with pre-attached wires and a connector (connector type may vary by batch), allowing quick installation in compatible devices. Moreover, it supports safe charging using standard 3.7V Lithium Polymer battery chargers or BMS protection circuits. ⚠️ Note: Charge the battery only with a compatible Lithium Polymer charger or charging protection module. Do not short-circuit, puncture, overcharge, or expose the battery to high temperatures. 🔹 Key Features Rechargeable Lithium Polymer (Li-Po) battery High energy density Compact and lightweight design Stable 3.7V output 700mAh capacity Long charge/discharge cycle life Low self-discharge Pre-attached connection wires Suitable for portable electronic devices Reliable and safe performance 🔹 Technical Specifications Battery Type: Lithium Polymer (Li-Po) Model: 503035 Nominal Voltage: 3.7V Full Charge Voltage: 4.2V Capacity: 700mAh Battery Dimensions: Approx. 5 × 30 × 35 mm Rechargeable: Yes Charging Method: CC/CV (Constant Current / Constant Voltage) Standard Charge Voltage: 4.2V Protection Circuit: May vary depending on batch Operating Temperature: -10°C to +60°C Weight: Approximately 15–18g 🔹 Applications This battery is suitable for: Bluetooth speakers Bluetooth headsets Mini drones RC toys Robotics projects IoT devices GPS trackers Portable electronic devices DIY electronics projects Wearable electronics 🔹 Package Includes 1 × 503035 3.7V 700mAh Rechargeable Lithium Polymer Battery
702025 3.7V 400mAh rechargeable Battery for Drone, Toys, Gaming, Robotics bluetoorh Headset, Bluetooth Speaker
[LiPo Cell] The 702025 3.7V 400mAh Rechargeable Lithium Polymer Battery is a compact and high-performance power source designed for portable electronic devices requiring lightweight and reliable energy storage. Built using advanced Lithium Polymer (Li-Po) technology, it provides high energy density, low self-discharge, and consistent output voltage. In addition, the battery delivers a nominal voltage of 3.7V with a capacity of 400mAh, making it suitable for powering compact electronic devices and embedded systems. As a result, it is widely used in drones, Bluetooth speakers, Bluetooth headsets, wireless gaming accessories, robotics, GPS devices, wearable electronics, and DIY battery-powered projects. Because of its slim profile and lightweight construction, the battery can be easily integrated into space-constrained applications. Furthermore, it supports multiple charge and discharge cycles while maintaining stable performance and long service life. The battery includes a pre-attached connector with insulated leads for quick installation and safe operation. Moreover, its rechargeable design makes it an economical and environmentally friendly power solution. ⚠️ Note: Charge the battery only with a compatible 3.7V Lithium Polymer battery charger or BMS protection circuit. 🔹 Key Features Rechargeable Lithium Polymer (Li-Po) battery High energy density Compact and lightweight design Stable 3.7V output Long charge/discharge cycle life Low self-discharge rate Pre-attached connection wires Suitable for portable electronic devices Reliable and safe performance Ideal for DIY electronics projects 🔹 Technical Specifications Battery Type: Lithium Polymer (Li-Po) Model: 702025 Nominal Voltage: 3.7V Full Charge Voltage: 4.2V Capacity: 400mAh Battery Dimensions: Approx. 7 × 20 × 25 mm Rechargeable: Yes Protection Circuit: Yes Charging Method: CC/CV (Constant Current / Constant Voltage) Operating Temperature: -10°C to +60°C Weight: Approximately 6–7g 🔹 Applications This battery is suitable for: Mini drones RC toys Bluetooth headsets Bluetooth speakers Wireless gaming controllers Robotics projects GPS trackers Wearable electronics DIY electronic devices Portable rechargeable products
3.7V BMS 1S 2A 18650 Lithium Battery Protection Board
[Lithium Battery Protection Board] The 1S 3.7V Lithium Battery Protection Board (BMS/PCM) is a compact battery management module designed specifically for single-cell lithium-ion batteries such as 18650, 14500, and similar 3.7V rechargeable cells. It continuously monitors battery voltage and current to ensure safe charging and discharging operations. In addition, the module provides multiple layers of protection including overcharge, over-discharge, overcurrent, and short-circuit protection. As a result, it helps extend battery life and improves the safety of battery-powered devices. Because of its compact size, the protection board can be easily integrated into DIY battery packs, portable electronics, LED lighting systems, and rechargeable battery projects. Furthermore, the board uses nickel-strip compatible terminals for easy battery pack assembly. The protection circuit is designed for long-term reliable operation and helps prevent damage caused by improper charging or excessive current draw. Moreover, it offers high voltage detection accuracy for improved battery management performance. ⚠️ Note: This protection board is designed for 3.7V Lithium-Ion batteries only and is not suitable for LiFePO4 batteries. 🔹 Key Features Single-cell (1S) lithium battery protection board Suitable for 18650 lithium-ion batteries Overcharge protection Over-discharge protection Overcurrent protection Short-circuit protection High voltage detection accuracy Compact and lightweight design Easy installation and integration Long operational life 🔹 Pin Configuration B+ : Battery Positive Terminal B- : Battery Negative Terminal P+ : Charge / Discharge Positive Terminal P- : Charge / Discharge Negative Terminal 🔹 Technical Specifications Product Type: Lithium Battery Protection Module (BMS/PCM) Battery Configuration: 1S (Single Cell) Compatible Battery Type: 3.7V Lithium-Ion (18650, 14500, etc.) Operating Voltage Range: 3.2V – 4.2V Overcharge Detection Voltage: 4.25 ± 0.05V Overcharge Release Voltage: 4.23 ± 0.05V Over-discharge Detection Voltage: 2.54 ± 0.1V Continuous Charge Current: 2A Continuous Discharge Current: 2A Maximum Supported Current: 2A – 5A Protection Functions: Overcharge, Over-discharge, Overcurrent, Short Circuit Terminal Type: Nickel Strip Compatible Board Life Expectancy: More than 20,000 Operating Hours 🔹 Applications This protection board is suitable for: 18650 battery packs Rechargeable lithium battery projects DIY power banks Portable electronics LED lighting systems Battery-powered devices Robotics projects Arduino and ESP32 power systems 🔹 Important Notes Not suitable for LiFePO4 batteries Not recommended for high-current motors above 4A Not suitable for electric bicycles or high-power battery packs Ensure correct polarity during installation Use only with compatible lithium-ion cells 🔹 Package Includes 1 × 1S 3.7V 2A Lithium-Ion Battery Protection Board (BMS/PCM)
TP4056 1A Li-Ion Lithium Battery Charging Module with Micro USB 3.7V Charger Board
[Li-ion Rechargeable Battery Charger, Lithium Battery Protection Board] The TP4056 1A Li-Ion Lithium Battery Charging Module – Micro USB is a compact and efficient charging board designed for charging single-cell 3.7V lithium-ion and lithium polymer batteries. It features an onboard Micro USB connector, allowing direct charging from USB power sources such as computers, adapters, and power banks. In addition, the module supports external power input through the IN+ and IN- pads, making it suitable for custom battery charging applications and DIY electronics projects. As a result, users can easily integrate the module into portable devices and battery-powered systems. Because of its compact size and lightweight design, the TP4056 module is ideal for space-limited applications. Furthermore, the onboard charging management IC provides stable charging performance with high accuracy and reliable battery protection. The charging current is set to 1A by default, but it can also be adjusted by changing the onboard programming resistor. Moreover, the module includes dual LED indicators for charging status and full-charge indication. This charging module is widely used in power banks, DIY battery chargers, portable electronics, IoT devices, robotics systems, and rechargeable battery projects. 🔹 Key Features TP4056 lithium battery charging IC Onboard Micro USB input interface Suitable for 3.7V Li-Ion and LiPo batteries Default 1A charging current Adjustable charging current support Dual LED charging status indicators Compact and lightweight design High charging accuracy and stable performance Easy integration into DIY projects 🔹 Technical Specifications Product Type: Lithium Battery Charging Module Charging IC: TP4056 Input Interface: Micro USB Input Voltage: 5V DC Battery Type: 3.7V Li-Ion / LiPo Battery Default Charging Current: 1A Adjustable Current Range: 100mA – 1000mA Charging Method: Constant Current / Constant Voltage Charging Indicators: Charging LED & Full Charge LED Mounting Type: PCB Module Body Material: FR4 PCB 🔹 Applications This TP4056 charging module is suitable for many electronic applications, including: DIY power banks Rechargeable battery projects Portable electronics Robotics systems IoT devices Battery charging circuits Arduino projects DIY electronics projects 🔹 Package Includes 1 × TP4056 1A Li-Ion Lithium Battery Charging Module – Micro USB
3A 250V Black Push Button ON/OFF Lock Switch Self Locking Push Switch
[Mechanical Switches] The 3A 250V Black Push Button ON/OFF Lock Switch is a compact and reliable self-locking push-type switch designed for permanent ON/OFF control applications. Unlike momentary switches, this switch remains locked in position after pressing until pressed again. In addition, the switch uses a stable locking mechanism that allows smooth operation and reliable switching performance. As a result, it is suitable for power control, equipment activation, and automation applications. Because of its compact size and durable plastic construction, the switch is ideal for many electronic and industrial projects. Furthermore, the black button provides a clean professional appearance that matches modern control panels and electronic enclosures. The switch supports loads up to 3A at 250VAC, making it suitable for both AC and low-voltage DC control circuits. Moreover, the panel-mount structure enables quick and secure installation into control panels and electronic devices. This ON/OFF lock switch is widely used in DIY electronics, industrial automation, robotics systems, power supplies, alarm systems, and electrical control circuits. 🔹 Key Features Self-locking ON/OFF push button switch Stable locking mechanism Compact and lightweight body Professional black push button cap Easy panel mounting installation Durable plastic construction Stable and reliable switching operation Suitable for AC and DC applications 🔹 Technical Specifications Switch Type: Push Button ON/OFF Lock Switch Contact Type: Self Locking Operation Type: Push ON / Push OFF Rated Voltage: 250V AC Rated Current: 3A Button Color: Black Mounting Type: Panel Mount Mounting Hole Diameter: Approx. 12mm Button Diameter: Approx. 12mm Total Length: Approx. 28mm Body Material: Plastic Contact Material: Silver-Plated Metal Terminal Type: 2 Pin Solder/Quick Connect Operating Temperature: -25°C to +85°C 🔹 Applications This push button lock switch is suitable for many electronic and electrical applications, including: DIY electronics projects Industrial control panels Automation systems Robotics projects Power control circuits Alarm systems Electronic devices Small appliances 🔹 Package Includes 1 × 3A 250V Black Push Button ON/OFF Lock Switch
3A 250V Blue Push Button ON/OFF Lock Switch Self Locking Push Switch
[Mechanical Switches] The 3A 250V Blue Push Button ON/OFF Lock Switch is a compact and reliable self-locking push-type switch designed for permanent ON/OFF control applications. Unlike momentary switches, this switch remains locked in position after pressing until pressed again. In addition, the switch uses a stable locking mechanism that allows easy operation and reliable switching performance. As a result, it is suitable for power control, equipment activation, and automation applications. Because of its compact size and durable plastic construction, the switch is ideal for many electronic and industrial projects. Furthermore, the bright blue button improves visibility and allows quick identification during operation. The switch supports loads up to 3A at 250VAC, making it suitable for both AC and low-voltage DC control circuits. Moreover, the panel-mount structure enables quick and secure installation into control panels and electronic enclosures. This ON/OFF lock switch is widely used in DIY electronics, industrial automation, robotics systems, power supplies, alarm systems, and electrical control circuits. 🔹 Key Features Self-locking ON/OFF push button switch Stable locking mechanism Compact and lightweight body Bright blue push button cap Easy panel mounting installation Durable plastic construction Stable and reliable switching operation Suitable for AC and DC applications 🔹 Technical Specifications Switch Type: Push Button ON/OFF Lock Switch Contact Type: Self Locking Operation Type: Push ON / Push OFF Rated Voltage: 250V AC Rated Current: 3A Button Color: Blue Mounting Type: Panel Mount Mounting Hole Diameter: Approx. 12mm Button Diameter: Approx. 12mm Total Length: Approx. 28mm Body Material: Plastic Contact Material: Silver-Plated Metal Terminal Type: 2 Pin Solder/Quick Connect Operating Temperature: -25°C to +85°C 🔹 Applications This push button lock switch is suitable for many electronic and electrical applications, including: DIY electronics projects Industrial control panels Automation systems Robotics projects Power control circuits Alarm systems Electronic devices Small appliances 🔹 Package Includes 1 × 3A 250V Blue Push Button ON/OFF Lock Switch