All products · 297 of 1440
Electronics, sensors, robotics kits, PC components, peripherals — everything Unik Systems carries, in one place.
Arduino Mega
Development board. ATmega2560, 54 digital I/O, 16 analog, perfect for big projects.
USB to DC Jack Cable
USB to DC jack cable, useful for power-bank-driven projects.
Out of stock0.96 Inch Blue SPI OLED Display Module 7-Pin 128×64 – SSD1306
[LED/LCD Display] 0.96 Inch Blue SPI OLED Display Module 7-Pin 128×64 – SSD1306 The 0.96-inch Blue OLED Display Module is a compact graphical display based on the SSD1306 driver IC, featuring a 128×64 pixel resolution and blue monochrome display. This version has a 7-pin interface with a dedicated CS (Chip Select) pin, making it suitable for 4-wire SPI communication. The module is factory-configured for SPI and can also be modified for I2C/IIC communication on compatible board versions. With its compact size, wide viewing angle and low-power OLED technology, it is suitable for Arduino, ESP32, ESP8266, STM32, Raspberry Pi and other microcontroller projects. ⭐ Key Features 0.96-inch blue OLED display 128 × 64 pixel resolution SSD1306 driver IC 7-pin interface Dedicated CS (Chip Select) pin Factory configured for 4-wire SPI Supports SPI and I2C/IIC with appropriate configuration 3.3V/5V compatible on supported module versions No backlight required Low power consumption Wide viewing angle of more than 160° Compact PCB design Pre-soldered 7-pin male header Compatible with Arduino, ESP32, ESP8266, STM32 and Raspberry Pi projects 📋 Technical Specifications Display Type: OLED (Organic Light-Emitting Diode) Display Colour: Blue Display Size: 0.96 inch Driver IC: SSD1306 Resolution: 128 × 64 pixels Interface: SPI / I2C Default Interface: 4-wire SPI Input Voltage: 3.3V–5V Viewing Angle: >160° Module Dimensions: Approximately 27 × 27 × 4mm Operating Temperature: Approximately -30°C to +70°C Header: 7-pin male header, pre-soldered Display Type: Monochrome blue OLED 🔌 7-Pin Interface The 7-pin version provides the following connections: GND – Ground VCC – Power supply D0 / SCK / CLK – SPI clock D1 / MOSI / SDA – SPI data RES / RST – Display reset DC / A0 – Data/Command selection CS – Chip Select 🛠️ SPI Connection The module is normally supplied in 4-wire SPI configuration. For an Arduino Uno, a typical connection is: VCC → 5V GND → GND D0 → SCK / D13 D1 → MOSI / D11 RES → Digital I/O DC → Digital I/O CS → Digital I/O The dedicated CS pin allows the OLED to share the SPI bus with other devices such as SD cards or additional SPI peripherals. 🔄 I2C / IIC Configuration On compatible versions, the module can be converted from SPI to I2C by changing the appropriate resistor configuration on the PCB. The supplied board configuration may require: Moving the resistor from R3 to R1 Shorting R8 with solder Using D0 as SCL Using D1 as SDA Configuring DC for the I2C address The exact resistor positions can vary between board revisions, so check the markings on your particular PCB before modification. 🎯 Applications Arduino projects ESP32 projects ESP8266 projects STM32 development Raspberry Pi projects IoT devices Sensor displays Voltage/current meters Battery monitors Temperature displays Digital clocks Data loggers Portable electronic devices Robotics DIY measuring instruments Embedded systems Menu and status displays 💡 Advantages of OLED OLED technology is self-emissive, meaning the pixels produce their own light and do not require a conventional backlight. This provides high contrast, compact construction and a wide viewing angle while keeping power consumption relatively low. ⚠️ Important Notes This is the 7-pin SPI version, not the 6-pin version. The module is normally configured for SPI communication. Check the PCB labels before connecting the module. Do not exceed the specified supply voltage. Although many versions support 5V operation, the exact voltage tolerance can vary between board revisions. I2C operation may require hardware resistor modification. The actual PCB layout and component markings may vary slightly between production batches. Display colour: Blue. Libraries such as Adafruit SSD1306 and U8g2 can be used with compatible microcontrollers. 📦 Package Includes 1 × 0.96 Inch Blue SPI OLED Display Module
2S 4A Type-C Lithium Battery Charging Module – 8.4V Step-Up Boost Charger for 18650 Lipo
[Step UP Buck Converter] 2S 4A Type-C Lithium Battery Charging Module – 8.4V Step-Up Boost Charger for 18650 The 2S 4A Type-C Lithium Battery Charging Module is a compact step-up charging board designed for charging 2-cell series (2S) 18650 Li-ion/Li-Po battery packs. It accepts a 3–6V DC input through USB Type-C and boosts the voltage to 8.4V, the required full-charge voltage for a 2S lithium battery pack. The 4A specification refers to the maximum input current version. According to available product specifications, the corresponding charging current is approximately 2.2A, rather than 4A. ⭐ Key Features Designed for 2S lithium-ion/Li-Po battery packs Suitable for 2 × 18650 cells connected in series USB Type-C input 3–6V DC input Recommended input: 3.7V / 5V Step-up/boost charging circuit 8.4V charging voltage 4A maximum input-current version Approximately 2.2A charging current Automatic recharge function Battery charging protection features Compact PCB design LED charging/status indication Suitable for DIY battery and portable-power projects 📋 Technical Specifications Product Type: 2S Lithium Battery Step-Up Charging Module Battery Configuration: 2S – 2 cells in series Compatible Battery: 3.6V/3.7V Li-ion / Li-Po Nominal Battery Pack Voltage: 7.4V Full-Charge Voltage: 8.4V Input Voltage: DC 3–6V Recommended Input: DC 3.7V / 5V Maximum Input Current: 4A Charging Current: Approximately 2.2A Charging Interface: USB Type-C Charging Mode: Constant-current / constant-voltage Board Size: Approximately 39 × 18 × 6.3mm Operating Temperature: -40°C to +85°C LED Indicators: Charging / fully charged or constant-voltage status 🔋 Charging Performance For the 2S 4A version: USB Type-C 5V → Boost Charging Module → 8.4V → 2S Battery Pack The module draws up to approximately 4A from the input, while the specified charging current is approximately 2.2A. This distinction is important when selecting the USB power adapter. 🔧 Applications 2S 18650 battery packs 7.4V Li-ion battery packs 2S Li-Po battery packs DIY power banks Portable electronics Bluetooth speaker battery systems Robotics projects Solar charging applications Electronic prototyping Portable audio equipment Electric fan projects Type-C rechargeable equipment Custom battery charging systems 🛠️ How It Works The module uses a boost/step-up charging circuit to convert the lower USB Type-C input voltage into the 8.4V charging voltage required for a 2S lithium battery pack. Example: 5V Type-C Input → Step-Up Circuit → 8.4V Charging Output → 2S 18650 Battery A 2S battery pack consists of two lithium cells connected in series: 3.7V + 3.7V = 7.4V nominal4.2V + 4.2V = 8.4V fully charged 💡 LED Indicators The module uses status indicators to show the charging condition: CR: Charging OK: Fully charged / constant-voltage stage ⚠️ Important Notes This module is intended for 2S battery packs only. Do not connect a single 18650 cell directly to the 8.4V charging output. The two cells should be properly matched and in good condition. Do not exceed the 6V maximum input voltage. A suitable Type-C power source is required to supply the necessary input current. The 4A rating is the input-current rating, not the battery charging current. The specified charging current for this 2S 4A version is approximately 2.2A. This charging module should not automatically be considered a replacement for a dedicated 2S BMS/protection board. Use appropriate battery protection where required. Check the PCB polarity and connection markings before connecting the battery. Do not short-circuit the input or output. Use properly matched lithium cells for safe and reliable charging. Keep the module adequately ventilated during higher-current operation. 📦 Package Includes 1 × 2S 4A Type-C Step-Up Boost Lithium Battery Charging Module – 8.4V
Type-C PD/QC/AFC Fast Charge Decoy Trigger Module – 5V/9V/12V/15V/20V Fixed Output
[Step UP Buck Converter] Type-C PD/QC/AFC Fast Charge Decoy Trigger Module – 5V/9V/12V/15V/20V Fixed Output The Type-C PD/QC/AFC Fast Charge Decoy Trigger Module is a compact USB Type-C power negotiation module designed to request a selected voltage from compatible USB Type-C fast chargers and power banks. It supports QC 2.0/3.0, AFC, PD 2.0 and PD 3.0 protocols, allowing compatible USB-C power sources to provide higher voltage outputs such as 5V, 9V, 12V, 15V or 20V. This module is useful for DIY electronics projects where a USB Type-C PD/QC charger needs to be used as a DC power source for equipment that does not have native USB-C fast-charging support. ⭐ Key Features USB Type-C fast-charge decoy/trigger module Supports PD 2.0 / PD 3.0 Supports QC 2.0 / QC 3.0 Supports Samsung AFC Fixed selectable voltage output Supports 5V / 9V / 12V / 15V / 20V output options Negotiates the required voltage from a compatible charger Suitable for USB-C power banks and PD adapters LED indicators for operating/status indication Compact and lightweight PCB design Useful for DIY power supply and electronics projects Plug-and-play operation with compatible USB-C power sources 📋 Technical Specifications Product Type: USB Type-C Fast Charge Trigger / Decoy Module Input Connector: USB Type-C Input Source: USB-C PD/QC/AFC compatible charger or power bank Supported Protocols: PD2.0, PD3.0, QC2.0, QC3.0, AFC Output Voltage: 5V / 9V / 12V / 15V / 20V Output Type: DC Voltage Selection: Fixed/selectable depending on module version Indicator: LED status indicators Application: DC power conversion and fast-charge voltage triggering 🔧 Applications Converting USB-C PD chargers into DC power supplies Powering DIY electronics projects Arduino and microcontroller projects LED applications Portable electronic equipment DIY laboratory power supplies DC motors and other suitable loads Router/modem power applications where the required voltage matches Powering electronics from USB-C PD power banks Replacing conventional DC adapters with USB-C PD sources 🛠️ How It Works The module does not boost the USB voltage itself. Instead, it communicates with a compatible USB-C power source and sends the required PD/QC/AFC negotiation request. For example, when connected to a compatible PD charger, the module can request: 5V → 9V → 12V → 15V → 20V The charger then provides the negotiated voltage at the module's DC output. ⚠️ Important Notes The connected USB-C charger or power bank must support the required fast-charging protocol and voltage. A standard 5V-only USB charger cannot normally provide 9V/12V/15V/20V through this module. Always verify the selected output voltage with a multimeter before connecting your device. Do not connect a device that requires a lower voltage than the selected output. The module is a trigger/decoy board, not a standalone DC-DC boost converter. Maximum available output power/current depends on the connected USB-C charger/power bank and the module's specifications. Do not short the output terminals. 20V output can damage 5V/9V/12V-only electronics if the wrong voltage is selected. Exact selectable voltages and current capability can vary between board versions. 📦 Package Includes 1 × Type-C PD/QC/AFC Fast Charge Decoy Trigger Module
UPS Rocker Switch Red 6 Pin ON-OFF-ON with Indicator
[Mechanical Switches] UPS Rocker Switch Red 6 Pin ON-OFF-ON with Indicator – BR34 The UPS Rocker Switch Red 6 Pin ON-OFF-ON with Indicator (BR34) is a durable rocker switch designed for reliable switching applications. It features a 6-pin DPDT configuration, copper contacts and a large rocker design with an indicator light for convenient operation and status indication. With a rated voltage of up to 250V and a rated current of 6A, it is suitable for UPS systems, power strips, stabilizers, water dispensers, coffee machines, automobiles, USB hubs, machinery and other electrical equipment. ⭐ Key Features 6-pin rocker switch ON-OFF-ON switching function DPDT switch configuration Red color Built-in indicator Copper contact construction Illuminated design Large rocker size Rated current up to 6A Rated voltage up to 250V Durable construction Suitable for panel-mount applications Indicator helps provide visual switching/status indication 📋 Technical Specifications Model: BR34 Switch Type: Rocker Switch Switch Function: ON-OFF-ON Number of Pins: 6 Switch Throw Type: DPDT Rated Voltage: 250V Rated Current: 6A Illuminated: Yes / With Indicator Indicator: Built-in indicator Contact Plating: Copper Material: Copper and Iron Color: Red Size: Big Rocker Mechanical Life: Up to 5 years Mounting: Panel Mount Application: Electrical and electronic equipment 🔧 Applications UPS systems Power strips Voltage stabilizers Water dispensers Coffee machines Automobiles USB hubs Electrical machinery DIY electrical projects Control panels Power switching applications 🛠️ Installation Ensure the power supply is switched OFF before installation. Identify the correct terminals according to the required DPDT switching configuration. Connect the wires securely to the appropriate terminals. Ensure the connected load does not exceed the 6A rated current. Mount the switch firmly into the appropriate panel cutout. Verify the indicator wiring and rating before connection. 📦 Package Includes 1 × UPS Rocker Switch Red 6 Pin ON-OFF-ON with Indicator Model: BR34 ⚠️ Precautions Do not exceed the rated 250V / 6A specification. Switch OFF the power supply before installation or wiring. Ensure proper insulation of all electrical connections. Use suitable wiring according to the connected load. Verify the indicator voltage specification before connecting it to the circuit. Verify the pin configuration before connecting the switch. Do not directly connect the indicator to a voltage for which it is not rated.
UPS Rocker Switch Black 6 Pin ON-OFF-ON
[Mechanical Switches] UPS Rocker Switch Black 6 Pin ON-OFF-ON – BR34 The UPS Rocker Switch Black 6 Pin ON-OFF-ON (BR34) is a durable rocker switch designed for reliable switching applications. It features a 6-pin DPDT configuration, copper contacts and a large rocker design for convenient operation. With a rated voltage of up to 250V and a rated current of 6A, it can be used in power strips, stabilizers, water dispensers, coffee machines, automobiles, USB hubs, machinery and other electrical equipment. ⭐ Key Features 6-pin rocker switch ON-OFF-ON switching function DPDT switch configuration Black color Copper contact construction Non-illuminated design Large rocker size Rated current up to 6A Rated voltage up to 250V Durable construction Suitable for panel-mount applications 📋 Technical Specifications Model: BR34 Switch Type: Rocker Switch Switch Function: ON-OFF-ON Number of Pins: 6 Switch Throw Type: DPDT Rated Voltage: 250V Rated Current: 6A Illuminated: No / Non-Illuminated Contact Plating: Copper Material: Copper and Iron Color: Black Size: Big Rocker Mechanical Life: Up to 5 years Mounting: Panel Mount Application: Electrical and electronic equipment 🔧 Applications UPS systems Power strips Voltage stabilizers Water dispensers Coffee machines Automobiles USB hubs Electrical machinery DIY electrical projects Control panels Power switching applications 🛠️ Installation Ensure the power supply is switched OFF before installation. Identify the correct terminals according to the required DPDT switching configuration. Connect the wires securely to the appropriate terminals. Ensure the connected load does not exceed the 6A rated current. Mount the switch firmly into the appropriate panel cutout. 📦 Package Includes 1 × UPS Rocker Switch Black 6 Pin ON-OFF-ON ⚠️ Precautions Do not exceed the rated 250V / 6A specification. Switch OFF the power supply before installation or wiring. Ensure proper insulation of all electrical connections. Use suitable wiring according to the connected load. This is a non-illuminated switch. Verify the pin configuration before connecting the switch to your circuit.
48mm Square Internal Magnet Speaker – 4Ohms 5W
[Speakers] 48mm Square Internal Magnet Speaker – 4Ω 5W The 48mm Square Internal Magnet Speaker is a compact full-range audio driver designed for clear and efficient sound reproduction in space-constrained applications. With a 4Ω impedance and 5W power rating, this speaker is suitable for Bluetooth speakers, portable audio systems, DIY speaker projects and embedded electronic devices. Its square frame allows convenient mounting inside compact enclosures and panels. ⭐ Key Features Compact square speaker design 4Ω impedance 5W power rating Internal magnet construction Full-range audio output Compact size for space-limited applications Easy to install inside speaker enclosures Suitable for DIY and commercial audio projects Lightweight and practical design 📋 Technical Specifications Speaker Type: Internal Magnet Speaker Shape: Square Speaker Size: 48mm class Model: 4Ω 5W Impedance: 4Ω Power Rating: 5W Magnet Type: Internal Magnet Audio Type: Full-range Mounting Type: Panel / Enclosure Mount Dimensions: 47 × 29 × 23mm Application: Compact audio systems, DIY electronics and portable speakers 🔧 Applications Bluetooth speaker systems Portable speakers DIY speaker projects Compact audio enclosures Embedded audio systems Intercom systems Alert and notification devices Educational electronics projects Consumer electronic devices Custom audio projects 🛠️ Installation Connect the speaker to a compatible amplifier with a 4Ω output. Ensure the amplifier's output power is suitable for the speaker's 5W rating. Mount the speaker securely inside the enclosure to reduce unwanted vibration. Observe correct speaker polarity when connecting multiple speakers. 📦 Package Includes 1 × 48mm Square Internal Magnet Speaker Impedance: 4Ω Power: 5W ⚠️ Precautions Do not exceed the 5W rated power for prolonged operation. Use a compatible 4Ω amplifier. Avoid short-circuiting the speaker terminals. Keep away from moisture, excessive heat and physical damage. Ensure proper mounting to minimize vibration and unwanted noise. Actual sound quality depends on the amplifier, enclosure and application.
Digital USB Mobile Power Charging Current Voltage Tester Meter
[Ammeter and Voltmeter] Digital USB Mobile Power Charging Current Voltage Tester Meter The Digital USB Mobile Power Charging Current Voltage Tester Meter is a compact USB testing device designed to measure and display charging voltage and current in real time. It is useful for checking the power output of USB chargers, power banks and other USB-powered devices. ⭐ Key Features Precise current and voltage measurement Simultaneous voltage and current display Bright digital LCD display Straight USB connector design USB Type-A Male input and USB Type-A Female output Compact and lightweight Easy to connect and use Suitable for USB chargers and power banks Compatible with USB-powered devices 📋 Technical Specifications Product Name: Digital USB Mobile Power Charging Current Voltage Tester Meter Color: As per available stock Input Voltage: 3.5V–7.0V Output Voltage: 3.5V–7.0V Current Measurement Range: 0A–3A Voltage Accuracy: ±1% Current Accuracy: ±1% Display Type: Digital LCD Display Screen Size: 0.91 inch Data Display: Voltage and Current simultaneously Power Consumption: ≤0.1W Interface: USB Type-A Male (Input) / USB Type-A Female (Output) Measurement Frequency: 2 times per second Operating Temperature: 0°C–45°C Material: ABS Plastic Dimensions: 64 × 23 × 15mm Weight: 15g Compatibility: USB-powered devices 🔧 Applications Mobile charger testing USB charger testing Power bank testing USB power supply testing Mobile phone charging analysis USB device testing Electronics troubleshooting DIY electronics projects Checking charging voltage and current 🛠️ How to Use Insert the USB Type-A Male connector into the USB charger, power bank or USB power source. Connect the USB-powered device to the USB Type-A Female output. The digital display will show the voltage and charging current. Monitor the readings during charging or testing. 📦 Package Includes 1 × Digital USB Mobile Power Charging Current Voltage Tester Meter ⚠️ Important Notes Do not exceed the specified voltage and current measurement ranges. This tester is intended for USB/DC applications. Actual readings may vary depending on the charger, cable and connected device. Use within the specified operating temperature range.
KWS-MX18 10-in-1 USB Tester Digital LCD Voltage, Current & Power Meter
[Ammeter and Voltmeter] KWS-MX18 10-in-1 USB Tester – Digital LCD Voltage, Current & Power Meter The KWS-MX18 10-in-1 USB Tester is a compact multifunction digital testing instrument designed for monitoring and evaluating USB chargers, power banks, USB ports, mobile charging systems, and other DC power sources. It provides real-time measurement of voltage, current, power, capacity, energy, charging time, resistance, and internal temperature on its digital display. The tester supports a DC voltage range of 4–30V and current measurement up to approximately 5.1A, with power measurement up to 150W. It also provides capacity and energy monitoring, making it useful for checking the actual charging performance and capacity of USB power supplies and power banks. ⭐ Key Features 10-in-1 multifunction USB tester Digital LCD display Real-time voltage and current monitoring Measures power consumption Measures accumulated charging capacity Measures energy consumption Charging time measurement Charging resistance measurement Internal temperature measurement Positive and negative voltage measurement Stores measurement data in 9 groups Power-off memory function Compact and lightweight design Suitable for USB charger and power-bank testing Supports QC2.0 / QC3.0 according to available product information 📋 Technical Specifications Product Type: 10-in-1 USB Digital Tester Model: KWS-MX18 Input Voltage Range: DC 4–30V Current Measurement: 0–5.1A Power Measurement: 0–150W Capacity Measurement: 0–999999mAh Energy Measurement: 0–999999mWh Timing Range: 0–99 Hours Charging Resistance: 0–999.9Ω Internal Temperature: 0–80°C Positive Voltage Measurement: 0–10V Negative Voltage Measurement: 0–10V Memory Groups: 1–9 Display: Digital LCD Material: ABS Dimensions: Approximately 56.6 × 24.7 × 11.2mm Weight: Approximately 13.9g Input Connector: USB Output Connector: USB Function Button: Yes 🔍 10 Measurement Functions Voltage: 4–30V DC Current: 0–5.1A Power: 0–150W Capacity: 0–999999mAh Energy: 0–999999mWh Charging Time: 0–99 hours Charging Resistance: 0–999.9Ω Positive Voltage: 0–10V Negative Voltage: 0–10V Internal Temperature: 0–80°C 💾 Memory Function The KWS-MX18 can store charging measurement information in 9 separate memory groups. This allows you to compare charging capacity and energy measurements from different chargers or devices. The stored data can be viewed using the function button, and an individual memory group can be cleared by holding the button for approximately 3 seconds. 🔘 Button Functions Single Press: View stored measurement data from memory groups 1–9. Long Press: Clear the currently selected memory group. Double Press: Change the display page. Calibration: The device supports voltage and current calibration according to the supplied manual. 🔌 Applications USB Charger Testing Mobile Charger Testing Power Bank Testing USB Port Testing Mobile Phone Charging Analysis USB Cable Testing Power Supply Monitoring DC Power Measurement Electronics Troubleshooting DIY Electronics Projects Charger Performance Testing Battery Charging Analysis 🛠️ How to Use Connect the KWS-MX18 in-line between the USB power source and the USB-powered device. Once powered, the LCD displays the measured electrical parameters. You can use the function button to change display pages and access stored measurement data. It is particularly useful for comparing chargers, power banks, cables, and USB ports by monitoring actual voltage, current, power, capacity, and energy delivered. 📦 Package Includes 1 × KWS-MX18 10-in-1 USB Digital Tester ⚠️ Color Note: Color: White / Black Color will be shipped depending on stock availability. Any one color (White or Black) may be shipped based on available stock. Specific color cannot be guaranteed. ⚠️ Precautions Do not exceed the specified 30V DC input voltage. Do not exceed the specified current measurement range. Ensure correct USB connection direction before use. Keep the tester away from water and excessive moisture. Do not use it for measuring mains AC voltage. The device is intended for DC/USB power measurement. Actual measurement accuracy can depend on the connected source, load, cable, and operating conditions.
Black Plastic 3×18650 Battery Holder or Case Series Connection With Wire
[Lithium Battery Holder] Black Plastic 3×18650 Battery Holder – Series Connection The Black Plastic 3×18650 Battery Holder is designed to securely hold three 18650 lithium-ion battery cells in series configuration. It provides a convenient and organized way to mount 18650 cells for DIY battery packs, portable electronics, power supplies, LED projects, and other battery-powered applications. The holder is made from durable plastic and features mounting holes for secure installation using suitable screws. It is supplied with red and black connecting wires for convenient connection to an external circuit. ⭐ Key Features Designed for 3 × 18650 battery cells Series connection Black plastic construction Without cover Secure battery positioning Easy installation Built-in mounting holes Red and black connecting wires Suitable for DIY battery pack projects Compact and lightweight design 📋 Technical Specifications Product Type: 18650 Battery Holder Battery Capacity: 3 Cells Battery Type: 18650 Li-Ion Cell Configuration: 3S / Series Connection Nominal Output Voltage: Approximately 11.1V with 3.7V cells Fully Charged Voltage: Approximately 12.6V Material: Plastic Color: Black Cover: Without Cover Connection Wires: Red and Black Mounting: Screw Mount Mounting Holes: Yes Recommended Screw Size: Approximately 3mm Application: Battery Pack / Portable Electronics 🔌 Connection The three 18650 cells are connected in series, increasing the total voltage while maintaining the capacity of a single cell. With standard 3.7V nominal cells, the pack is approximately 11.1V nominal and 12.6V when fully charged. The red wire is the positive connection and the black wire is the negative connection. 🔧 Applications DIY 18650 Battery Packs 3S Lithium-Ion Battery Packs Portable Electronics LED Lighting Projects DIY UPS Projects Arduino Projects ESP8266 / ESP32 Projects Rechargeable Electronics Battery-Powered Devices Electronics Prototyping 📦 Package Includes 1 × 3×18650 Battery Holder / Case – Series Connection, Without Cover ⚠️ Precautions Use only compatible 18650 Li-Ion cells. Use three cells with matching capacity, chemistry, age, and charge condition. Use a suitable 3S BMS/protection and charging circuit. Do not mix damaged or mismatched cells. Check polarity carefully before installation. Do not short-circuit the battery terminals. Do not use damaged, swollen, or leaking cells. Ensure the holder and wiring are securely installed.
25 Watt Soldering Iron with 3mm Tip
[Soldering Iron] 25W Soldering Iron – Deluxe Economic The 25W Soldering Iron – Deluxe Economic is a compact and practical soldering tool designed for electronics assembly, component soldering, PCB repair, circuit modifications, and general-purpose electronic work. With a 25W heating element and included 3mm spade tip, it provides a convenient solution for routine soldering applications. The soldering iron features a quick-heating element to reduce waiting time before operation. It is compatible with most standard soldering tips available on the market, making it suitable for both hobbyists and professional electronics repair work. This soldering iron is manufactured in India and may be supplied under SAMCON, Devaji, Noel, Alpine, or an equivalent manufacturer, depending on availability. ⭐ Key Features 25W power output Includes 3mm spade tip Quick-heating capability Compatible with most standard soldering tips Compact and practical design Suitable for PCB soldering and repair Durable construction for general electronics work Suitable for hobbyists, technicians, and educational use Made in India 📋 Technical Specifications Product Type: Electric Soldering Iron Model: Deluxe Economic Power Rating: 25W Tip Type: 3mm Spade Tip: 3mm Spade Tip, Pre-Installed Heating Type: Quick Heating Tip Compatibility: Most Standard Soldering Tips Manufacturer: SAMCON / Devaji / Noel / Alpine or Equivalent Country of Origin: India Application: Electronics Soldering and PCB Repair 🔧 Applications General Electronics Component Soldering PCB Assembly PCB Repair Circuit Modifications Electronics Hobby Projects DIY Electronics Educational Electronics Workshops Component Replacement Wire Soldering General Electrical & Electronic Repair 🛠️ How to Use Insert a suitable soldering tip and allow the iron to heat up. Apply solder to the heated joint and component connection to create a proper electrical and mechanical connection. After completing the work, place the soldering iron safely on a heat-resistant stand and allow it to cool before storage. 📦 Package Includes 1 × 25W Soldering Iron 1 × 3mm Spade Tip (Pre-Installed) ⚠️ Precautions The soldering tip becomes extremely hot during operation. Do not touch the heated tip or metal parts during use. Always place the soldering iron on a suitable heat-resistant stand when not in use. Use in a well-ventilated area. Wear appropriate eye protection during soldering. Keep away from children and flammable materials. Disconnect from the power supply after use. Allow the iron to cool completely before changing the tip. Lead-free solder may require higher temperatures and may not perform optimally with every 25W soldering application. ❓ Frequently Asked Questions Q: Can the 3mm spade tip be replaced?A: Yes. The supplied specification states that the soldering iron is compatible with most standard soldering tips, allowing tip replacement. Q: What safety precautions are required?A: Use the soldering iron in a well-ventilated area, use eye protection, and place it on a heat-resistant stand when not in use. Q: Is it compatible with lead-free solder?A: It can be used with lead-free solder, although lead-free soldering may require higher temperatures depending on the application.
Out of stockGold AP-55 TPA3116D2 2×50W Bluetooth Stereo Digital Amplifier Board with USB, TF Card, FM & Remote
[Amplifier Board] Gold AP-55 TPA3116D2 2×50W Bluetooth Stereo Digital Amplifier Board with USB, TF Card, FM & Remote The Gold AP-55 is a compact Class-D stereo digital audio amplifier board based on the TPA3116D2 amplifier IC, designed for DIY Bluetooth speakers, home audio systems, portable speakers, bookshelf speakers, multimedia systems, and custom audio projects. Available product listings consistently identify the AP-55 as a dual-channel 50W + 50W amplifier, with a DC input range around 8–24V or 12–24V depending on the listing/version. The AP-55 combines the power amplifier with a multimedia player supporting Bluetooth 5.0, USB, TF/SD card, FM radio and AUX input. The Bluetooth device name is reported as GD-82EM, while the FM tuner covers 87.5–108.0MHz. It also includes an infrared remote control and a digital display for convenient operation. The TPA3116D2 Class-D amplifier provides efficient stereo amplification, making the board suitable for building compact but powerful audio systems. One detailed listing specifies support for 4Ω–8Ω speakers, with the commonly advertised maximum output of 50W per channel. ⭐ Key Features Gold AP-55 amplifier module TPA3116D2 Class-D amplifier IC 50W + 50W dual-channel stereo output Supports 4Ω–8Ω speakers Bluetooth 5.0 wireless audio Bluetooth device name: GD-82EM Built-in USB music player Built-in TF / SD card player Built-in FM radio FM frequency range 87.5–108.0MHz 3.5mm AUX input Infrared remote control Digital display Supports MP3 / WMA / WAV Power-off memory function Remembers the previous song and volume Compact design for DIY speaker projects High-efficiency Class-D amplification 📋 Technical Specifications Product Type: Stereo Class-D Digital Amplifier Board Model: Gold AP-55 Amplifier IC: TPA3116D2 Amplifier Class: Class-D Number of Channels: 2 / Stereo Output Power: 50W + 50W Maximum Total Output: 100W Speaker Impedance: 4Ω–8Ω Input Voltage: DC 8–24V (some listings specify 12–24V; verify the exact board version before use) Bluetooth Version: 5.0 Bluetooth Name: GD-82EM Bluetooth Range: Up to approximately 10–15m under suitable conditions Audio Formats: MP3 / WMA / WAV USB Support: Yes TF/SD Card Support: Yes FM Radio: Yes FM Frequency: 87.5–108.0MHz AUX Input: 3.5mm / Wired Audio Input Remote Control: IR Remote Remote Range: Approximately 4–7m Display: Digital Display Power-Off Memory: Yes Memory Function: Last song and volume Audio Input Modes: Bluetooth / USB / TF Card / FM / AUX Output: Dual-Channel Stereo Efficiency: Greater than 90% according to one detailed listing SNR: Approximately 102dB according to one detailed listing Distortion: Below 0.1% at normal listening levels according to one detailed listing Board Size: Approximately 70 × 50 × 20mm with shell, according to one listing 🎵 Audio & Playback Functions The AP-55 can switch between Bluetooth, USB, TF/SD Card, FM Radio and AUX sources. When Bluetooth mode is selected, users can pair a phone or other compatible device with GD-82EM. USB and TF/SD cards can be used for local music playback, while AUX provides a wired audio input. 📻 FM Radio The built-in FM tuner supports the 87.5–108.0MHz broadcast band. FM stations can be searched and selected using the onboard controls or remote control. 🎛️ Controls & Remote The module provides controls for functions such as previous track, next track, volume up, volume down, play/pause, mode selection and FM station selection. The infrared remote provides additional wireless control of playback, volume, mode and other supported functions. 🔧 Applications DIY Bluetooth Speakers High-Power Bluetooth Speaker Projects Portable Speaker Systems Bookshelf Speaker Systems Home Audio Projects Multimedia Speaker Systems USB MP3 Speaker Systems TF/SD Card Music Players FM Radio Speaker Projects Car Audio Projects Custom Wooden Speaker Cabinets Desktop Audio Systems Electronics DIY Projects 🛠️ Installation Connect a suitable DC power supply within the specified voltage range and observe the correct polarity. Connect the left and right speaker outputs to compatible 4Ω–8Ω speakers. Select Bluetooth, USB, TF/SD, FM or AUX according to the desired audio source. For maximum advertised output, a suitable 24V high-current power supply is recommended by one vendor; at lower supply voltages, available output power will be lower. 📦 Package Includes 1 × Gold AP-55 TPA3116D2 2×50W Bluetooth Amplifier Board 1 × IR Remote Control 1 × Required Connecting Wires/Cables (package contents may vary by seller/version) ⚠️ Precautions Verify the exact input voltage requirement of your AP-55 version before powering it. Do not exceed 24V DC where the board specification limits input to 24V. Check power polarity carefully before connection. Use speakers with a compatible 4Ω–8Ω impedance. Do not short-circuit the speaker output terminals. Ensure adequate ventilation during high-power operation. Use a suitable high-current power supply for high-output operation. Do not connect the speaker outputs together or directly to ground. Keep the board away from moisture and conductive materials. Incorrect wiring or excessive voltage can permanently damage the amplifier IC.
45mm 1.75-Inch 4Ohms 3W Internal Magnet Speaker with Frame
[Speakers] 45mm Internal Magnet Speaker with Frame – 4Ω 3W 45×23×23mm The 45mm Internal Magnet Speaker with Frame (1.75-Inch) is a compact and efficient audio driver designed for DIY electronics, portable audio devices, multimedia systems, toys, alarms, intercoms, and embedded audio applications. Featuring an internal magnet structure and durable mounting frame, this speaker provides clear and stable sound output while maintaining a compact form factor. With a compact size of 45×23×23mm, 4Ω impedance, and 3W power rating, this speaker is suitable for small amplifier projects and electronic devices where space is limited. Its built-in frame allows convenient installation in custom enclosures, panels, and electronic products. ⭐ Key Features 45mm (1.75-Inch) speaker size 4Ω impedance 3W power rating Internal magnet design Durable mounting frame Compact 45×23×23mm construction Clear and stable sound output Lightweight and space-saving Suitable for low-power audio applications Easy to install in custom enclosures Ideal for DIY, repair and OEM applications 📋 Technical Specifications Product Type: Internal Magnet Speaker Speaker Size: 45mm (1.75 Inch) Dimensions: 45 × 23 × 23mm Impedance: 4Ω Power Rating: 3W Magnet Type: Internal Magnet Frame Type: With Mounting Frame Speaker Type: Dynamic Full Range Speaker Audio Type: Mini Full Range Speaker Mounting: Frame / Panel Mount Application: Compact Audio & Embedded Electronics 🔧 Applications DIY Speaker Projects Portable Audio Devices Bluetooth Speaker Projects Multimedia Speaker Systems Alarm Systems Toys and Sound Modules Intercom Systems Embedded Electronics Educational Electronics Kits Replacement Speaker Repairs Smart Gadgets OEM Product Manufacturing Mini Amplifier Projects 🛠️ Installation Mount the speaker securely inside the required enclosure or panel using its mounting frame. Connect it to a compatible amplifier with an output suitable for 4Ω speakers and a power rating appropriate for the 3W speaker. Proper mounting helps reduce unwanted vibration and improves overall sound performance. 📦 Package Includes 1 × 45mm Internal Magnet Speaker with Frame – 4Ω 3W ⚠️ Precautions Match the 4Ω impedance with the amplifier output. Do not exceed the 3W rated power. Do not apply direct DC voltage to the speaker. Ensure correct wiring polarity during installation. Avoid exposure to moisture and excessive dust. Mount securely to prevent vibration and unwanted noise. Do not apply physical pressure to the speaker cone or diaphragm. Use a compatible audio amplifier module for proper operation.
2 Inch 4 Ohms 5Watt Internal Magnet Speaker with Frame
[Speakers] 2-Inch Internal Magnet Speaker with Frame – 53×29×23mm 4Ω 5W The 2-Inch Internal Magnet Speaker with Frame is a compact and efficient audio driver designed for DIY electronics, portable audio devices, alarms, toys, embedded systems, and other space-constrained applications. Featuring an internal magnet design and durable frame construction, this speaker provides clear and balanced sound output while maintaining a compact footprint. With dimensions of 53×29×23mm, 4Ω impedance, and a 5W power rating, this speaker is suitable for small amplifier projects and electronic devices requiring a compact audio solution. The mounting frame makes installation convenient in custom enclosures and equipment. ⭐ Key Features 2-Inch compact speaker design Internal magnet structure 4Ω impedance 5W power rating Durable metal frame construction Clear and balanced sound output Compact and space-saving design Easy mounting with frame and screw slots Suitable for low and medium-power audio applications Ideal for DIY and OEM applications 📋 Technical Specifications Product Type: Dynamic Internal Magnet Speaker Speaker Size: 2 Inch Dimensions: 53 × 29 × 23mm Impedance: 4Ω Power Rating: 5W Magnet Type: Internal Magnet Magnet Material: Ferrite Shape: Rectangular Frame Type: Metal Frame Cone Material: Paper / Mylar Diaphragm depending on variant Speaker Type: Full Range / Dynamic Speaker Mounting: Frame with Screw Slots Application: Compact Audio & Embedded Electronics 🔧 Applications DIY Speaker Projects Portable Audio Devices Bluetooth Speaker Projects Alarm Systems Toys and Sound Modules Intercom Systems Embedded Electronics Educational Electronics Kits Replacement Speaker Repairs Smart Gadgets OEM Product Manufacturing Mini Amplifier Projects 🛠️ Installation Connect the speaker to a compatible amplifier output matching the speaker's 4Ω impedance and 5W power rating. Secure the speaker firmly using the mounting frame to reduce unwanted vibration and noise during operation. 📦 Package Includes 1 × 2-Inch Internal Magnet Speaker with Frame – 4Ω 5W ⚠️ Precautions Match the 4Ω impedance with the amplifier output. Do not exceed the 5W rated power. Avoid applying direct DC voltage to the speaker. Avoid exposure to moisture and excessive humidity. Mount the speaker securely before operation. Do not apply physical pressure to the speaker cone or diaphragm. Avoid short circuits at the speaker terminals. Keep the speaker away from excessive heat and magnetic interference.
1K Ohm Rotary Potentiometer Round Shaft 3 Pin Elcon
[Potentiometer] 1KΩ Rotary Potentiometer Round Shaft Elcon The 1KΩ Rotary Potentiometer Round Shaft Elcon is a reliable 3-pin linear rotary potentiometer designed for adjusting electrical parameters such as voltage, current, brightness, motor speed, and other control functions in electronic circuits. By rotating the shaft, the resistance can be smoothly adjusted across its available range, making it suitable for a wide variety of DIY and electronic applications. With its compact 16mm body, 6mm round shaft, and through-hole mounting design, this potentiometer is easy to install on electronic PCBs and control panels. Its linear resistance characteristics make it suitable for applications such as LED brightness control, fan speed control, motor control, power supply adjustment, and general-purpose voltage control. ⭐ Key Features 1KΩ resistance value 3-pin rotary potentiometer Linear potentiometer Smooth rotary adjustment 6mm round shaft 10mm shaft length Compact 16mm body diameter Through-hole mounting Suitable for PCB and electronic circuits Ideal for voltage and resistance adjustment Suitable for DIY and electronic projects Elcon brand 📋 Technical Specifications Product Type: Rotary Potentiometer Brand: Elcon Resistance Value: 1KΩ Configuration: 3 Pin / Single Gang Tolerance: ±20% Shaft Type: Round Shaft Shaft Diameter: 6mm Shaft Length: 10mm Body Diameter / Width: 16mm Total Height: Approx. 25mm Mounting Type: Through Hole Operating Temperature: -40°C to +80°C Weight: Approx. 8g 🔧 Applications LED Brightness Control Fan Speed Control Motor Speed Control Voltage Adjustment Current Adjustment Power Supply Circuits Audio & Electronic Circuits Arduino Projects DIY Electronics Projects Electronic Prototyping 🛠️ How It Works A potentiometer is a variable resistor with three terminals. The two outer terminals are connected to the resistive track, while the center terminal acts as the wiper. Rotating the shaft changes the wiper position and therefore changes the resistance or output voltage in the circuit. 📦 Package Includes 1 × 1KΩ Rotary Potentiometer Round Shaft Elcon ⚠️ Note Product images are shown for illustrative purposes only and may differ slightly from the actual product. The 1KΩ value, tolerance, dimensions, and shaft length should be verified against the actual product batch before installation.
5K Ohms Rotary Potentiometer Round Shaft 3 Pin Elcon
[Potentiometer] 5KΩ Rotary Potentiometer Round Shaft Elcon The 5KΩ Rotary Potentiometer Round Shaft Elcon is a reliable 3-pin linear rotary potentiometer designed for adjusting electrical parameters such as voltage, current, brightness, motor speed, and other control functions in electronic circuits. By rotating the shaft, the resistance can be smoothly adjusted across its available range, making it suitable for a wide variety of DIY and electronic applications. With its compact 16mm body, 6mm round shaft, and through-hole mounting design, this potentiometer is easy to install on electronic PCBs and control panels. Its linear resistance characteristics make it suitable for applications such as LED brightness control, fan speed control, motor control, power supply adjustment, and general-purpose voltage control. ⭐ Key Features 5KΩ resistance value 3-pin rotary potentiometer Linear potentiometer Smooth rotary adjustment 6mm round shaft 13mm shaft length Compact 16mm body diameter Through-hole mounting Suitable for PCB and electronic circuits Ideal for voltage and resistance adjustment Suitable for DIY and electronic projects Elcon brand 📋 Technical Specifications Product Type: Rotary Potentiometer Brand: Elcon Resistance Value: 5KΩ Configuration: 3 Pin / Single Gang Tolerance: ±20% Shaft Type: Round Shaft Shaft Diameter: 6mm Shaft Length: 13mm Body Diameter / Width: 16mm Total Height: Approx. 28mm Mounting Type: Through Hole Operating Temperature: -40°C to +80°C Weight: Approx. 8g 🔧 Applications LED Brightness Control Fan Speed Control Motor Speed Control Voltage Adjustment Current Adjustment Power Supply Circuits Audio & Electronic Circuits Arduino Projects DIY Electronics Projects Electronic Prototyping 🛠️ How It Works A potentiometer is a variable resistor with three terminals. The two outer terminals are connected to the resistive track, while the center terminal acts as the wiper. Rotating the shaft changes the wiper position and therefore changes the resistance or output voltage in the circuit. 📦 Package Includes 1 × 5KΩ Rotary Potentiometer Round Shaft Elcon ⚠️ Note Product images are shown for illustrative purposes only and may differ slightly from the actual product. The 5KΩ value, tolerance, dimensions, and shaft length should be verified against the actual product batch
16 sq mm Copper Ring Lug Cable Terminal
[Terminal Connector] 16 sq mm Pure Copper Ring Lug Cable Terminal The 16 sq mm Pure Copper Ring Lug Cable Terminal is a high-quality electrical cable lug designed for making secure and reliable connections in high-current electrical systems. Made from pure copper, it provides excellent electrical conductivity and a strong mechanical connection between the cable and the terminal point. The ring lug design allows the terminal to be securely fastened to battery terminals, busbars, studs, bolts, and other electrical connection points. It is suitable for battery packs, inverters, UPS systems, solar installations, automotive wiring, and industrial electrical applications. The compact construction provides a reliable connection while allowing easy installation using a suitable crimping tool. The terminal is ideal for applications where a strong and low-resistance electrical connection is required. ⭐ Key Features Made from pure copper Designed for 16 sq mm cable Ring lug terminal design Excellent electrical conductivity Strong and reliable mechanical connection Suitable for high-current applications Easy bolt and stud mounting Suitable for battery and power wiring Ideal for electrical and DIY applications 📋 Technical Specifications Product Type: Copper Ring Cable Lug Material: Pure Copper Compatible Cable Size: 16 sq mm Terminal Type: Ring Lug Finish: Natural Copper / Tinned, depending on variant Connection Type: Bolt / Stud Mount Application: High-Current Electrical Connections 🔧 Applications Lithium Battery Packs LiFePO₄ Battery Systems Lead-Acid Batteries Inverter Connections UPS Systems Solar Power Systems Automotive Wiring Electrical Panels Power Distribution Industrial Wiring DIY Battery Projects 📦 Package Includes 1 × 16 sq mm Pure Copper Ring Lug Cable Terminal ⚠️ Precautions Select the correct lug according to the 16 sq mm cable size and required mounting hole diameter. Use a suitable cable-lug crimping tool for a secure connection. Ensure the cable is properly inserted and crimped before use. Do not exceed the safe current capacity of the cable and terminal assembly. Ensure all electrical connections are properly insulated and secured.
2.25-Inch 8ohms 8W Full Range Speaker for Compact Audio Applications
[Speakers] 2.25-Inch 8Ω 8W Full Range Speaker for Compact Audio Applications The 2.25-Inch 8Ω 8W Full Range Speaker is a compact and efficient audio driver designed for small electronic and embedded sound applications. Featuring an 8Ω impedance and 8W power rating, this speaker delivers clear and balanced sound output while maintaining low power consumption and excellent efficiency. Its compact size makes it ideal for projects where installation space is limited, including portable speakers, DIY electronics, toys, alarm systems, intercom devices, and mini speaker enclosures. The full-range design allows it to reproduce a broad range of audio frequencies, making it suitable for both voice and music playback applications. Built with durable materials and designed for reliable long-term performance, this speaker is an excellent choice for electronics hobbyists, engineers, and product developers working on custom audio projects. ⭐ Key Features 2.25-Inch compact speaker driver 8Ω impedance 8W power rating Full-range audio reproduction Clear and balanced sound output Lightweight and compact design Easy to mount in enclosures and panels Suitable for low to medium-power audio applications Durable construction for long-term use Ideal for DIY and embedded audio systems 📋 Technical Specifications Product Type: Full Range Speaker Speaker Size: 2.25 Inch Impedance: 8Ω Power Rating: 8W Speaker Type: Full Range Mounting Type: Enclosure / Panel Mount Application Type: Audio Output 🔧 Applications Portable Speaker Systems DIY Audio Projects Bluetooth Speaker Modules Toys and Educational Kits Alarm and Notification Systems Embedded Electronic Devices Mini Amplifiers and Sound Modules Intercom Systems Robotics Projects Custom Speaker Enclosures ⚠️ Precautions Do not exceed the 8W rated power. Use an amplifier compatible with an 8Ω speaker load. Avoid exposure to moisture and excessive dust. Mount securely to minimize vibration and distortion. Do not apply direct pressure on the speaker cone. 📦 Package Includes 1 × 2.25-Inch 8Ω 8W Full Range Speaker
57mm (2.25-Inch) Internal Magnet Speaker 4Ohms 3W Full Range Audio Speaker
[Speakers] 57mm (2.25-Inch) Internal Magnet Speaker – 4Ω 3W Full Range Audio Speaker The 57mm (2.25-Inch) Internal Magnet Speaker is a compact and reliable full-range audio speaker designed for DIY electronics, multimedia devices, embedded sound systems, and portable audio applications. Featuring a 4Ω impedance and 3W power rating, this speaker delivers clear and balanced sound output while maintaining a slim and lightweight design. Its internal magnet structure provides a compact profile, making it ideal for applications where installation space is limited. The durable mounting frame allows easy integration into speaker enclosures, control panels, intercom systems, audio modules, and custom electronic projects. Designed for consistent audio performance, this speaker is suitable for voice playback, music, alerts, and general audio output in both portable and embedded electronic devices. ⭐ Key Features 57mm (2.25-Inch) compact speaker 4Ω impedance 3W power rating Internal magnet design Full-range audio reproduction Built-in mounting frame Clear and balanced sound output Compact and lightweight construction Easy installation in custom enclosures Suitable for portable and embedded audio applications Ideal for DIY electronics and speaker projects 📋 Technical Specifications Product Type: Internal Magnet Speaker Speaker Size: 57mm (2.25 Inch) Impedance: 4Ω Power Rating: 3W Speaker Type: Full Range Magnet Type: Internal Magnet Frame Type: With Mounting Frame Mounting: Frame / Panel Mount Application: Embedded Audio Systems 🔧 Applications DIY Electronics Projects Audio Modules & Music Players Intercom and Communication Systems Toys and Educational Devices Portable Audio Systems Alarm and Notification Devices Embedded Audio Applications Mini Speaker Enclosures Multimedia Devices Robotics and Automation Projects ⚠️ Precautions Do not exceed the 3W rated power. Use an amplifier compatible with a 4Ω speaker load. Ensure proper wiring polarity during installation. Avoid exposure to moisture and dust. Mount securely to reduce vibration noise. Do not apply direct pressure on the speaker cone. 📦 Package Includes 1 × 57mm (2.25-Inch) 4Ω 3W Internal Magnet Full Range Speaker
45mm (1.75-Inch) Internal Magnet Speaker 2 Ohms 10W Full Range Audio Speaker
[Speakers] 45mm (1.75-Inch) Internal Magnet Speaker – 2Ω 10W Full Range Audio Speaker The 45mm (1.75-Inch) Internal Magnet Speaker is a compact and powerful audio driver designed for DIY electronics, portable speakers, multimedia devices, toys, embedded audio systems, and custom speaker enclosures. Featuring a 2Ω impedance and 10W power rating, this speaker provides strong audio output when paired with a compatible amplifier. Its internal magnet design provides a compact profile while maintaining efficient magnetic performance. The built-in mounting frame makes installation easy in custom enclosures and electronic devices. With its 2Ω low-impedance configuration, this speaker is suitable for compatible Class-D amplifier modules where higher output power is required from a compact speaker driver. ⭐ Key Features 45mm (1.75-Inch) compact speaker 2Ω impedance 10W power rating Internal magnet design Full-range audio reproduction Compact and lightweight construction Built-in mounting frame Clear and powerful sound output Easy to install in custom enclosures Suitable for portable and embedded audio applications Ideal for DIY speaker projects 📋 Technical Specifications Product Type: Internal Magnet Speaker Speaker Size: 45mm (1.75 Inch) Impedance: 2Ω Power Rating: 10W Speaker Type: Full Range Magnet Type: Internal Magnet Frame Type: Mounting Frame Mounting: Frame / Panel Mount Application: Embedded & Portable Audio 🔧 Applications DIY Bluetooth Speaker Projects Portable Speaker Systems Mini Audio Amplifiers Multimedia Devices Toys and Educational Kits Intercom Systems Alarm and Notification Systems Embedded Audio Devices Custom Speaker Enclosures Robotics Projects Electronic Projects ⚠️ Precautions Use an amplifier that supports a 2Ω load. Do not exceed the 10W rated power. Check amplifier output impedance before connecting. Observe correct speaker polarity during installation. Avoid excessive mechanical pressure on the speaker cone. Keep away from moisture and excessive dust. Mount securely to minimize unwanted vibration and distortion. 📦 Package Includes 1 × 45mm (1.75-Inch) 2Ω 10W Internal Magnet Full Range Speaker
2.25 Inch 4 Ohm 10 Watt Full Range Speaker with Neodymium Magnet
[Speakers] 2.25-Inch Speaker Driver • 4 Ohm Impedance • 10W Power Rating • Neodymium Magnet • Compact Full Range Audio Speaker The 2.25 Inch 4 Ohm 10 Watt Full Range Speaker with Neodymium Magnet is a compact and high-performance speaker driver designed for portable audio systems, DIY speaker projects, multimedia devices, embedded electronics, and custom sound enclosures. Featuring a powerful neodymium magnet, this speaker delivers clear vocals, balanced midrange, and improved bass response while maintaining a lightweight and compact design. With a 4 ohm impedance and 10 watt power rating, the speaker is suitable for use with small audio amplifiers, Bluetooth amplifier modules, DIY portable speakers, mini sound systems, toys, alarm systems, educational kits, and embedded electronic devices. The full-range design allows it to reproduce a wide spectrum of audio frequencies without requiring additional tweeters for many compact applications. Its durable construction and lightweight neodymium magnet assembly make it ideal for applications where both performance and space efficiency are important. ⭐ Features Compact 2.25-inch full range speaker Powerful neodymium magnet 4 ohm impedance 10 watt power rating Clear and balanced sound output Enhanced vocal clarity and midrange performance Lightweight and compact construction Easy to mount in custom enclosures Suitable for portable and embedded audio systems Ideal for DIY electronics and audio projects 📋 Technical Specifications Product Type: Full Range Speaker Driver Speaker Size: 2.25 Inch Impedance: 4 Ohm Power Rating: 10 Watt Magnet Type: Neodymium Speaker Type: Full Range Mounting Type: Enclosure / Panel Mount Application Type: Audio Output Frame Material: Metal Cone Material: Paper Composite Color: Black 🔧 Applications Suitable for: Portable Speaker Systems Bluetooth Speakers DIY Audio Projects Mini Sound Systems Multimedia Devices Toys and Educational Kits Alarm and Notification Systems Embedded Electronic Devices Mini Amplifiers Sound Modules Intercom Systems Custom Speaker Enclosures Robotics and Electronics Projects 📦 Package Includes 1 × 2.25 Inch 4 Ohm 10 Watt Full Range Speaker with Neodymium Magnet ⚠️ Precautions Do not exceed the 10W rated power. Use an amplifier compatible with 4 ohm speakers. Avoid exposure to moisture, water, and excessive dust. Mount the speaker securely to minimize unwanted vibration. Do not apply direct pressure to the speaker cone or surround.
802580 LiPo Battery 700mAh 3.7V High Discharge 25c for Drone
[LiPo Cell] LiPo Battery 700mAh 3.7V High Discharge 802580 3.7V Lithium Polymer Battery • 700mAh Capacity • 25C High Discharge • 802580 Cell • Molex 2.0mm 2-Pin Connector The LiPo Battery 700mAh 3.7V High Discharge 802580 is a compact and lightweight Lithium Polymer (LiPo) rechargeable battery designed for applications that require high current output in a small form factor. Built with high-quality lithium polymer cells, this battery delivers a nominal voltage of 3.7V and a 700mAh capacity, making it ideal for RC toys, drones, mini helicopters, robotics, wireless electronics, and DIY projects. With a 25C continuous discharge rating, this battery can provide rapid bursts of current for motors and other high-power devices. The battery comes with a Molex 2.0mm 2-pin connector and an integrated protection PCB, offering added safety during charging and discharging. The 802580 cell size refers to the approximate dimensions of 8.0 × 25 × 80 mm, allowing the battery to fit easily into compact electronic devices while maintaining excellent power-to-weight performance. Note: This battery is intended for high-discharge applications such as RC models and robotics. It is not recommended for long-duration low-current devices such as cameras or data loggers. ⭐ Features High-quality 3.7V 700mAh LiPo battery 25C continuous discharge capability Compact 802580 cell size Lightweight design Stable voltage output Built-in protection circuit (PCB) Pre-installed Molex 2.0mm 2-pin connector Excellent power-to-weight ratio Rechargeable and reusable Suitable for high-current applications Easy plug-and-play installation 📋 Technical Specifications Product Type: Rechargeable Lithium Polymer (LiPo) Battery Battery Chemistry: Lithium Polymer (Li-ion Polymer) Cell Size: 802580 Nominal Voltage: 3.7V Full Charge Voltage: 4.20V Typical Capacity: 700mAh Discharge Rating: 25C Continuous Dimensions: Approx. 8.0 × 25 × 80 mm Weight: Approx. 18g Connector Type: Molex 2.0mm 2-Pin Protection Circuit: Built-in PCB Protection Rechargeable: Yes 🔧 Applications Suitable for: RC Cars RC Airplanes RC Helicopters Drones & Quadcopters Robotics Projects Arduino Projects ESP32 Projects DIY Electronics Portable Devices Wireless Modules Educational Projects Electronic Prototyping Battery Replacement Projects Miniature Electronics 📦 Package Includes 1 × LiPo Battery 700mAh 3.7V High Discharge 802580 with Molex 2.0mm 2-Pin Connector ⚠️ Safety Instructions Use only LiPo-compatible chargers. Do not charge above 4.20V. Do not discharge below the recommended cut-off voltage. Do not short-circuit the battery terminals. Do not puncture, crush, or expose the battery to fire. Store partially charged in a cool, dry place when not in use. Ensure connector polarity matches your device before connection.