All products · 31 of 1440
Electronics, sensors, robotics kits, PC components, peripherals — everything Unik Systems carries, in one place.
Arduino Plug & Play
Controller: Arduino UNO/Nano compatible (ATmega328P), 5V logic. Interfaces: Digital I/O, PWM, Analog In, I2C/SPI/UART. USB programming. Plug-and-play sensor ports (JST/RJ/3-pin). Power: USB 5V / DC 7–12V (if UNO).
IOT Plug & Play
MCU: ESP8266/ESP32 based (Wi-Fi 2.4GHz). Supply: 5V input, onboard 3.3V regulation. Protocols: MQTT/HTTP. Cloud/App support. GPIO with pre-wired ports. Typical sensors: DHT11/22, LDR, relay module, IR, PIR.
Snap Circuit Kit
Circuit modules with snap connectors. Power: 2×AA / 3×AA / 9V (kit dependent). Components: switches, LEDs, buzzer, motor, resistors, capacitors. No soldering. Safe low-voltage learning.
Only 2 leftRobotic Arm Kit
DOF: 3–6 (kit dependent). Actuators: servo motors (SG90/MG90/MG996R class). Control: Arduino/servo driver (PCA9685 common). Supply: 5–6V for servos (separate recommended). Payload: light (50–200g typical for small kits).
Only 1 leftDrone Kit
Frame: 180–250mm class. Motors: brushless 2204/2205/2300KV. ESC: 20A–30A. Flight controller: F4/F7 (or basic for edu kits). Battery: LiPo 3S/4S. Props: 5-inch typical. Radio: 2.4GHz. Prop guards recommended.
Only 1 leftIOT Smarthome Kit
MCU: ESP8266/ESP32. Modules: 1–4 channel relay (optocoupled preferred), PIR, LDR, DHT. Control: app/web dashboard. Protocols: MQTT/HTTP. Power: 5V input. Properly isolated AC relay use.
Breadboard Kit
Breadboard: 400/830 tie-points. Jumpers: M-M, M-F. Common parts: resistors (¼W), LEDs, push buttons, potentiometer. Modules: LDR, buzzer, IR, PIR, relay. Power module: 3.3V/5V rails (optional).
Roboki
Mechanical parts kit: beams, brackets, shafts, bushings, gears, pulleys, wheels. Materials: ABS/nylon/metal mix. Build type: screw/slot. Concepts: gear ratio, torque, linkages. Compatible with DC/servo mounts.
Paper Circuit Kit
Conductive copper foil tape. Power: 3V coin cell (CR2032). Components: LEDs (3mm/5mm), push switch, battery holder. Use: series/parallel circuits on paper. Safe low-voltage.
Only 2 leftRobotic Spider Kit
Legs: 4/6/8-legged variants. Servos: 8–12 micro servos. Controller: Arduino/ESP32 compatible. Gait programming. Power: 5–6V high-current (2A–5A depending on servos). Frame: acrylic/ABS.
Only 2 leftOtto
Biped robot kit. Servos: 4 micro servos (legs/feet). MCU: Arduino Nano compatible. Sensors: ultrasonic + buzzer. Power: 5V (battery pack). Programming: Arduino IDE / block coding. Functions: walk/dance/avoid.
Only 1 leftPlay Mex
MCU: ESP8266/ESP32. Sensors: soil moisture (capacitive preferred), temp/humidity (DHT), light sensor. Actuation: relay/pump/solenoid valve demo. Dashboard: MQTT/HTTP. Power: 5V input + relay isolation.
Only 1 leftIOT Health Kit
MCU: ESP32 (good ADC/BLE). Sensors: pulse sensor/PPG module, body temp sensor, SpO2 module optional. Data logging: serial/cloud. Power: 5V USB. Educational use, non-clinical.
Only 1 leftPlay Tronix
Airframe: foam/balsa/corrugated. Components: propeller, DC motor/brushless, servo(s), control horns, pushrods. Electronics: ESC (if brushless), battery. Concepts: lift/drag/thrust, CG/balance.
Only 2 leftRC Car Kit
Chassis: 2WD/4WD. Motors: TT DC geared motors (3–6V) or higher. Driver: L298N/L293D. Controller: Arduino/ESP32 optional. Remote: IR/2.4GHz/Bluetooth. Power: 2×18650 or 4×AA. Optional ultrasonic/line sensor.
G.Skill Ripjaws V 16 GB (2×8) DDR4 3600
Faster sub-timings than 3200 kits, CL16. Sweet spot for AM4 (Ryzen 5000) IF performance.
45mm 1.75-Inch 4Ohms 3W Internal Magnet Speaker with Frame
[Speakers] 45mm Internal Magnet Speaker with Frame – 4Ω 3W 45×23×23mm The 45mm Internal Magnet Speaker with Frame (1.75-Inch) is a compact and efficient audio driver designed for DIY electronics, portable audio devices, multimedia systems, toys, alarms, intercoms, and embedded audio applications. Featuring an internal magnet structure and durable mounting frame, this speaker provides clear and stable sound output while maintaining a compact form factor. With a compact size of 45×23×23mm, 4Ω impedance, and 3W power rating, this speaker is suitable for small amplifier projects and electronic devices where space is limited. Its built-in frame allows convenient installation in custom enclosures, panels, and electronic products. ⭐ Key Features 45mm (1.75-Inch) speaker size 4Ω impedance 3W power rating Internal magnet design Durable mounting frame Compact 45×23×23mm construction Clear and stable sound output Lightweight and space-saving Suitable for low-power audio applications Easy to install in custom enclosures Ideal for DIY, repair and OEM applications 📋 Technical Specifications Product Type: Internal Magnet Speaker Speaker Size: 45mm (1.75 Inch) Dimensions: 45 × 23 × 23mm Impedance: 4Ω Power Rating: 3W Magnet Type: Internal Magnet Frame Type: With Mounting Frame Speaker Type: Dynamic Full Range Speaker Audio Type: Mini Full Range Speaker Mounting: Frame / Panel Mount Application: Compact Audio & Embedded Electronics 🔧 Applications DIY Speaker Projects Portable Audio Devices Bluetooth Speaker Projects Multimedia Speaker Systems Alarm Systems Toys and Sound Modules Intercom Systems Embedded Electronics Educational Electronics Kits Replacement Speaker Repairs Smart Gadgets OEM Product Manufacturing Mini Amplifier Projects 🛠️ Installation Mount the speaker securely inside the required enclosure or panel using its mounting frame. Connect it to a compatible amplifier with an output suitable for 4Ω speakers and a power rating appropriate for the 3W speaker. Proper mounting helps reduce unwanted vibration and improves overall sound performance. 📦 Package Includes 1 × 45mm Internal Magnet Speaker with Frame – 4Ω 3W ⚠️ Precautions Match the 4Ω impedance with the amplifier output. Do not exceed the 3W rated power. Do not apply direct DC voltage to the speaker. Ensure correct wiring polarity during installation. Avoid exposure to moisture and excessive dust. Mount securely to prevent vibration and unwanted noise. Do not apply physical pressure to the speaker cone or diaphragm. Use a compatible audio amplifier module for proper operation.
2 Inch 4 Ohms 5Watt Internal Magnet Speaker with Frame
[Speakers] 2-Inch Internal Magnet Speaker with Frame – 53×29×23mm 4Ω 5W The 2-Inch Internal Magnet Speaker with Frame is a compact and efficient audio driver designed for DIY electronics, portable audio devices, alarms, toys, embedded systems, and other space-constrained applications. Featuring an internal magnet design and durable frame construction, this speaker provides clear and balanced sound output while maintaining a compact footprint. With dimensions of 53×29×23mm, 4Ω impedance, and a 5W power rating, this speaker is suitable for small amplifier projects and electronic devices requiring a compact audio solution. The mounting frame makes installation convenient in custom enclosures and equipment. ⭐ Key Features 2-Inch compact speaker design Internal magnet structure 4Ω impedance 5W power rating Durable metal frame construction Clear and balanced sound output Compact and space-saving design Easy mounting with frame and screw slots Suitable for low and medium-power audio applications Ideal for DIY and OEM applications 📋 Technical Specifications Product Type: Dynamic Internal Magnet Speaker Speaker Size: 2 Inch Dimensions: 53 × 29 × 23mm Impedance: 4Ω Power Rating: 5W Magnet Type: Internal Magnet Magnet Material: Ferrite Shape: Rectangular Frame Type: Metal Frame Cone Material: Paper / Mylar Diaphragm depending on variant Speaker Type: Full Range / Dynamic Speaker Mounting: Frame with Screw Slots Application: Compact Audio & Embedded Electronics 🔧 Applications DIY Speaker Projects Portable Audio Devices Bluetooth Speaker Projects Alarm Systems Toys and Sound Modules Intercom Systems Embedded Electronics Educational Electronics Kits Replacement Speaker Repairs Smart Gadgets OEM Product Manufacturing Mini Amplifier Projects 🛠️ Installation Connect the speaker to a compatible amplifier output matching the speaker's 4Ω impedance and 5W power rating. Secure the speaker firmly using the mounting frame to reduce unwanted vibration and noise during operation. 📦 Package Includes 1 × 2-Inch Internal Magnet Speaker with Frame – 4Ω 5W ⚠️ Precautions Match the 4Ω impedance with the amplifier output. Do not exceed the 5W rated power. Avoid applying direct DC voltage to the speaker. Avoid exposure to moisture and excessive humidity. Mount the speaker securely before operation. Do not apply physical pressure to the speaker cone or diaphragm. Avoid short circuits at the speaker terminals. Keep the speaker away from excessive heat and magnetic interference.
2.25-Inch 8ohms 8W Full Range Speaker for Compact Audio Applications
[Speakers] 2.25-Inch 8Ω 8W Full Range Speaker for Compact Audio Applications The 2.25-Inch 8Ω 8W Full Range Speaker is a compact and efficient audio driver designed for small electronic and embedded sound applications. Featuring an 8Ω impedance and 8W power rating, this speaker delivers clear and balanced sound output while maintaining low power consumption and excellent efficiency. Its compact size makes it ideal for projects where installation space is limited, including portable speakers, DIY electronics, toys, alarm systems, intercom devices, and mini speaker enclosures. The full-range design allows it to reproduce a broad range of audio frequencies, making it suitable for both voice and music playback applications. Built with durable materials and designed for reliable long-term performance, this speaker is an excellent choice for electronics hobbyists, engineers, and product developers working on custom audio projects. ⭐ Key Features 2.25-Inch compact speaker driver 8Ω impedance 8W power rating Full-range audio reproduction Clear and balanced sound output Lightweight and compact design Easy to mount in enclosures and panels Suitable for low to medium-power audio applications Durable construction for long-term use Ideal for DIY and embedded audio systems 📋 Technical Specifications Product Type: Full Range Speaker Speaker Size: 2.25 Inch Impedance: 8Ω Power Rating: 8W Speaker Type: Full Range Mounting Type: Enclosure / Panel Mount Application Type: Audio Output 🔧 Applications Portable Speaker Systems DIY Audio Projects Bluetooth Speaker Modules Toys and Educational Kits Alarm and Notification Systems Embedded Electronic Devices Mini Amplifiers and Sound Modules Intercom Systems Robotics Projects Custom Speaker Enclosures ⚠️ Precautions Do not exceed the 8W rated power. Use an amplifier compatible with an 8Ω speaker load. Avoid exposure to moisture and excessive dust. Mount securely to minimize vibration and distortion. Do not apply direct pressure on the speaker cone. 📦 Package Includes 1 × 2.25-Inch 8Ω 8W Full Range Speaker
45mm (1.75-Inch) Internal Magnet Speaker 2 Ohms 10W Full Range Audio Speaker
[Speakers] 45mm (1.75-Inch) Internal Magnet Speaker – 2Ω 10W Full Range Audio Speaker The 45mm (1.75-Inch) Internal Magnet Speaker is a compact and powerful audio driver designed for DIY electronics, portable speakers, multimedia devices, toys, embedded audio systems, and custom speaker enclosures. Featuring a 2Ω impedance and 10W power rating, this speaker provides strong audio output when paired with a compatible amplifier. Its internal magnet design provides a compact profile while maintaining efficient magnetic performance. The built-in mounting frame makes installation easy in custom enclosures and electronic devices. With its 2Ω low-impedance configuration, this speaker is suitable for compatible Class-D amplifier modules where higher output power is required from a compact speaker driver. ⭐ Key Features 45mm (1.75-Inch) compact speaker 2Ω impedance 10W power rating Internal magnet design Full-range audio reproduction Compact and lightweight construction Built-in mounting frame Clear and powerful sound output Easy to install in custom enclosures Suitable for portable and embedded audio applications Ideal for DIY speaker projects 📋 Technical Specifications Product Type: Internal Magnet Speaker Speaker Size: 45mm (1.75 Inch) Impedance: 2Ω Power Rating: 10W Speaker Type: Full Range Magnet Type: Internal Magnet Frame Type: Mounting Frame Mounting: Frame / Panel Mount Application: Embedded & Portable Audio 🔧 Applications DIY Bluetooth Speaker Projects Portable Speaker Systems Mini Audio Amplifiers Multimedia Devices Toys and Educational Kits Intercom Systems Alarm and Notification Systems Embedded Audio Devices Custom Speaker Enclosures Robotics Projects Electronic Projects ⚠️ Precautions Use an amplifier that supports a 2Ω load. Do not exceed the 10W rated power. Check amplifier output impedance before connecting. Observe correct speaker polarity during installation. Avoid excessive mechanical pressure on the speaker cone. Keep away from moisture and excessive dust. Mount securely to minimize unwanted vibration and distortion. 📦 Package Includes 1 × 45mm (1.75-Inch) 2Ω 10W Internal Magnet Full Range Speaker
2.25 Inch 4 Ohm 10 Watt Full Range Speaker with Neodymium Magnet
[Speakers] 2.25-Inch Speaker Driver • 4 Ohm Impedance • 10W Power Rating • Neodymium Magnet • Compact Full Range Audio Speaker The 2.25 Inch 4 Ohm 10 Watt Full Range Speaker with Neodymium Magnet is a compact and high-performance speaker driver designed for portable audio systems, DIY speaker projects, multimedia devices, embedded electronics, and custom sound enclosures. Featuring a powerful neodymium magnet, this speaker delivers clear vocals, balanced midrange, and improved bass response while maintaining a lightweight and compact design. With a 4 ohm impedance and 10 watt power rating, the speaker is suitable for use with small audio amplifiers, Bluetooth amplifier modules, DIY portable speakers, mini sound systems, toys, alarm systems, educational kits, and embedded electronic devices. The full-range design allows it to reproduce a wide spectrum of audio frequencies without requiring additional tweeters for many compact applications. Its durable construction and lightweight neodymium magnet assembly make it ideal for applications where both performance and space efficiency are important. ⭐ Features Compact 2.25-inch full range speaker Powerful neodymium magnet 4 ohm impedance 10 watt power rating Clear and balanced sound output Enhanced vocal clarity and midrange performance Lightweight and compact construction Easy to mount in custom enclosures Suitable for portable and embedded audio systems Ideal for DIY electronics and audio projects 📋 Technical Specifications Product Type: Full Range Speaker Driver Speaker Size: 2.25 Inch Impedance: 4 Ohm Power Rating: 10 Watt Magnet Type: Neodymium Speaker Type: Full Range Mounting Type: Enclosure / Panel Mount Application Type: Audio Output Frame Material: Metal Cone Material: Paper Composite Color: Black 🔧 Applications Suitable for: Portable Speaker Systems Bluetooth Speakers DIY Audio Projects Mini Sound Systems Multimedia Devices Toys and Educational Kits Alarm and Notification Systems Embedded Electronic Devices Mini Amplifiers Sound Modules Intercom Systems Custom Speaker Enclosures Robotics and Electronics Projects 📦 Package Includes 1 × 2.25 Inch 4 Ohm 10 Watt Full Range Speaker with Neodymium Magnet ⚠️ Precautions Do not exceed the 10W rated power. Use an amplifier compatible with 4 ohm speakers. Avoid exposure to moisture, water, and excessive dust. Mount the speaker securely to minimize unwanted vibration. Do not apply direct pressure to the speaker cone or surround.
5V 100mA 0.5W Mini Solar Panel 70x70mm Polycrystalline DIY Solar Cell Charger
[Solar Panel] The 5V 100mA 0.5W Mini Solar Panel is a compact and efficient photovoltaic module designed for small solar power applications and DIY renewable energy projects. Made using high-quality polycrystalline silicon, this solar panel converts sunlight into usable electrical energy with reliable performance. In addition, the panel delivers a stable 5V output with up to 100mA current, making it suitable for charging small batteries, powering low-power devices, and educational electronics projects. As a result, it is widely used in portable solar applications, science experiments, and DIY electronic systems. Because of its lightweight and compact design, the panel can be easily installed in limited spaces. Furthermore, the durable epoxy surface improves protection against moisture and environmental conditions, helping ensure long-term outdoor use. The solar panel features excellent low-light performance and high conversion efficiency for improved energy generation. Moreover, the exposed copper connection pads allow easy soldering and quick integration into custom electronic projects. This mini photovoltaic panel is commonly used in solar DIY kits, battery chargers, garden lighting, educational projects, portable electronics, and renewable energy systems. 🔹 Key Features High-efficiency polycrystalline solar panel Stable 5V output voltage Lightweight and compact design Excellent low-light performance Durable epoxy-coated surface Easy soldering connection pads Waterproof and long-lasting structure Suitable for DIY and educational projects 🔹 Technical Specifications Product Type: Mini Solar Panel Material: Polycrystalline Silicon Output Voltage: 5V Output Current: 0–100mA Rated Power: 0.5W Dimensions: 70mm × 70mm × 3mm Surface Type: Epoxy Coated Connection Type: Copper Tape Pads Application Type: Solar Charging / DIY Projects 🔹 Applications This mini solar panel is suitable for many applications, including: DIY solar projects Small battery charging Educational electronics kits Portable solar devices Garden lighting systems Renewable energy experiments Low-power electronics projects 🔹 Package Includes 1 × 5V 100mA 0.5W Mini Epoxy Solar Panel
500mAh 3.7V Single Cell Rechargeable LiPo Battery (HCY-602530)
[LiPo Cell] 500mAh Rechargeable 3.7v LiPo Battery The 600mAh Rechargeable 3.7V LiPo Battery is a compact and high-performance power source designed for a wide range of DIY electronics, robotics, and wearable projects. With a nominal voltage of 3.7V and capacity of 500mAh, this 1S lithium polymer battery delivers a reliable and consistent power output for your low-to-medium power applications. Its lightweight and slim profile make it ideal for portable gadgets, RC toys, sensors, and IoT devices that require stable energy without adding bulk. One of the key advantages of this battery is its long-lasting runtime when used with efficient electronics. For example, if a device consumes an average current of just 2mA, the 600mAh capacity allows the battery to run for up to 300 hours (600mAh / 2mA) under ideal conditions. This impressive endurance highlights the battery’s suitability for long-duration tasks, especially in energy-conscious designs. With Witty Fox’s reputation for quality and durability, this LiPo battery is a dependable choice for both hobbyists and professionals looking for efficient power solutions. Features: High Capacity: 600mAh gives little devices a longer runtime. Consistent Performance: A nominal voltage of 3.7V guarantees stable output. It is rechargeable, so it can be used repeatedly for extended periods of time. Small Design: Elongated and light, ideal for projects with limited area Up to 300 hours of use at a current draw of 2mA is supported by smart power efficiency. Multiple embedded systems, microcontroller boards, and robotics kits can all be used with this versatile tool. Specifications: Specification Details Brand HCY Battery Type Lithium Polymer (LiPo) Nominal Voltage 3.7V Nominal Capacity 500mAh Battery Cell Configuration 1S (Single Cell) Rechargeable Yes Dimensions (LxWxH) 30 x 25 x 6 mm Weight 8 g(approx) Package Includes: 3.7V 500mAH (Lithium Polymer) Lipo Rechargeable Battery (Model – 602530)
Single Shaft BO Motor 100 RPM
[Gear Motor] 100 RPM Single Shaft BO Motor – Straight Shaft The 100 RPM Single Shaft BO Motor is a lightweight and cost-effective solution designed for DIY robotics, small automation systems, and educational projects. Offering an excellent balance between torque and speed at low operating voltages, this motor is ideal for small to medium-sized robots. With its compact and durable construction, the motor features pre-drilled mounting holes for easy installation and perfectly pairs with 69mm robot wheels, making it an excellent choice for 2WD mobile robot platforms. Its low noise, low power consumption, and reliable torque output make it a favorite among hobbyists, students, and developers. Specifications: Shaft Length: 7mm Shaft Diameter: 5.5mm Motor Size: 55 × 48 × 23mm Voltage Range: 3V – 12V DC No-load Current: 40 – 180mA Speed: 100 RPM @ 6V Torque: 0.35 kg-cm Key Features: Lightweight and compact design Cost-effective with injection-molded housing Resilient, shock-absorbing construction Low power consumption and minimal maintenance Quiet operation with reduced friction Corrosion-resistant for long life Easy mounting with pre-drilled holes Ideal For: DIY robotics and automation projects Line follower and obstacle-avoiding robots Educational robotics kits Small mechanical prototypes Package Includes: 1 × 100 RPM Single Shaft BO Motor (Straight Shaft)