DC Micro Horizontal Two Nozzle Submersible Water Pump for Fish Tank Fountain Aquarium
- •Product Name: DC Micro Horizontal Two Nozzle Submersible Water Pump for Fish Tank Fountain Aquarium
- •Product Category: Motors & Actuators
- •Operating Voltage: 6V - 28V DC
- •Operating Temperature: -20°C to +65°C
- •Mounting Type: Through Hole / Screw Terminal / Modular
- •Efficiency / Accuracy: Up to 95%
- •It can take up to 120 liters per hour with a very low current consumption of 220mA
- •Just connect tube pipe to the motor outlet, submerge it in water, and power it
Description
[DC Water Pump] Double Side Pipe Submersible and Non-Submersible Mini Water Pump Features – Micro/Mini Water Pump Operating Voltage: DC 3-6 V Power : 3 W Maximum lift : 40-110cm / 15.75″-43.4″ Flow rate: 80-120L/H Material: Engineering plastic This DC 3-6 V Mini Micro Submersible Water Pump is a low-cost, small-size Submersible Pump Motor which can be operated from a 3 ~ 6V power supply. It can take up to 120 liters per hour with a very low current consumption of 220mA. Just connect tube pipe to the motor outlet, submerge it in water, and power it.
🔹 Key Features
- •It can take up to 120 liters per hour with a very low current consumption of 220mA
- •Just connect tube pipe to the motor outlet, submerge it in water, and power it
🔹 Technical Specifications
🔹 Pin Configuration & Wiring
⚠️ Direct MCU GPIO Connection Hazard
DC Micro Horizontal Two Nozzle Submersible Water Pump for Fish Tank Fountain Aquarium is an inductive electro-mechanical load drawing up to 200mA – 1A+ surge current. An ESP32 GPIO pin is rated for only 12mA (Arduino Uno is rated for 20mA).
Never wire this motor directly to ESP32 / Arduino pins. Doing so will immediately destroy the microcontroller's output transistors due to inrush current and reverse back-EMF inductive voltage spikes. Always use an intermediate motor driver or transistor switch with a common ground.
Recommended Driver & Interfacing Architectures
Select your interfacing method to inspect the exact wiring diagram & code
Connection Matrix
// Safe Motor & Air Pump PWM Speed Control using L298N Driver
// Tested for Arduino Uno & ESP32 (with ESP32 ledcWrite)
#define ENA_PIN 9 // Connect to L298N ENA (PWM speed control)
#define IN1_PIN 8 // Connect to L298N IN1 (Direction / ON)
#define IN2_PIN 7 // Connect to L298N IN2 (Direction / OFF)
void setup() {
pinMode(ENA_PIN, OUTPUT);
pinMode(IN1_PIN, OUTPUT);
pinMode(IN2_PIN, OUTPUT);
// Initialize driver in OFF state
digitalWrite(IN1_PIN, LOW);
digitalWrite(IN2_PIN, LOW);
analogWrite(ENA_PIN, 0);
}
void loop() {
// Soft start: ramp up speed to prevent inrush current spikes
digitalWrite(IN1_PIN, HIGH);
digitalWrite(IN2_PIN, LOW);
for (int speed = 100; speed <= 255; speed += 15) {
analogWrite(ENA_PIN, speed);
delay(50);
}
delay(3000); // Run motor at full speed for 3 seconds
// Coast to stop
digitalWrite(IN1_PIN, LOW);
digitalWrite(IN2_PIN, LOW);
analogWrite(ENA_PIN, 0);
delay(2000); // Pause for 2 seconds
}🔹 Applications
This component is engineered and suitable for:
- •DC motor speed regulation and soft start control
- •Robotics drive train and wheel speed adjustment
- •Cooling fans, exhaust blowers, and thermal management
- •Miniature water pumps and aquarium aeration systems
- •DIY electronics projects, automation circuits, and laboratory benches
🔹 Package Includes
- ✓1 × DC Micro Horizontal Two Nozzle Submersible Water Pump for Fish Tank Fountain Aquarium
Wholesale Tiered Pricing
Autonomous 4WD AI & Obstacle Rover Kit
Build a complete 4-wheel drive robotics rover with ultrasonic distance sensing & motor driver control.

Related products
Complementary hardware and compatible components for your project





