Electronics · 1023 of 1023
Arduino, ESP32, sensors, robotics kits, tools, safety gear — built for makers, schools, and SCM teams.
Arduino Plug & Play
Controller: Arduino UNO/Nano compatible (ATmega328P), 5V logic. Interfaces: Digital I/O, PWM, Analog In, I2C/SPI/UART. USB programming. Plug-and-play sensor por
IOT Plug & Play
MCU: ESP8266/ESP32 based (Wi-Fi 2.4GHz). Supply: 5V input, onboard 3.3V regulation. Protocols: MQTT/HTTP. Cloud/App support. GPIO with pre-wired ports. Typical
Snap Circuit Kit
Circuit modules with snap connectors. Power: 2×AA / 3×AA / 9V (kit dependent). Components: switches, LEDs, buzzer, motor, resistors, capacitors. No soldering. S
Only 1 left3D Printer
Type: FDM/FFF. Nozzle: 0.4mm. Filament: PLA/ABS/PETG 1.75mm. Build volume ~220×220×250mm (typical classroom size). Layer height 0.1–0.3mm. Bed: heated optional.
Only 2 leftRobotic Arm Kit
DOF: 3–6 (kit dependent). Actuators: servo motors (SG90/MG90/MG996R class). Control: Arduino/servo driver (PCA9685 common). Supply: 5–6V for servos (separate re
Only 1 leftDrone Kit
Frame: 180–250mm class. Motors: brushless 2204/2205/2300KV. ESC: 20A–30A. Flight controller: F4/F7 (or basic for edu kits). Battery: LiPo 3S/4S. Props: 5-inch t
Only 1 leftIOT Smarthome Kit
MCU: ESP8266/ESP32. Modules: 1–4 channel relay (optocoupled preferred), PIR, LDR, DHT. Control: app/web dashboard. Protocols: MQTT/HTTP. Power: 5V input. Proper
Arduino UNO
Hardware development board (SMD/DIP). ATmega328P, 14 digital I/O, 6 analog, USB-B.
Only 1 leftBambu Lab A1 Mini 3D Printer
Bambu Lab A1 Mini compact 3D printer.
Soldering Kit (15-30W)
Variable wattage 15-30W/230V soldering iron. 280–450°C. De-soldering pump, flux paste, solder wick, 5 tips, soldering wire.
Digital Multimeter
7 functions, 19 ranges. DC voltage 200mV–1kV, AC voltage 200–750V, DC current 200µA–10A, resistance 200–2MΩ, transistor & diode test.
Quarky
Educational STEM controller board. USB programmable. Block coding + Python/Arduino-like. Built-in sensors (mic, light, IMU) + ports for external sensors/servos.
3D Pen Kit
Nozzle temp ~180–230°C (varies by filament). Filament: PLA/ABS 1.75mm. Power: 5V/2A or 12V adapter (model-dependent). Adjustable feed speed. Tips/nozzles includ
Breadboard Kit
Breadboard: 400/830 tie-points. Jumpers: M-M, M-F. Common parts: resistors (¼W), LEDs, push buttons, potentiometer. Modules: LDR, buzzer, IR, PIR, relay. Power
Roboki
Mechanical parts kit: beams, brackets, shafts, bushings, gears, pulleys, wheels. Materials: ABS/nylon/metal mix. Build type: screw/slot. Concepts: gear ratio, t
Paper Circuit Kit
Conductive copper foil tape. Power: 3V coin cell (CR2032). Components: LEDs (3mm/5mm), push switch, battery holder. Use: series/parallel circuits on paper. Safe
